[PATCH 7/8] drm/panel: nt35510: refactor panel initialization
Dario Binacchi
dario.binacchi at amarulasolutions.com
Fri Dec 29 13:51:22 UTC 2023
The previous implementation did not make it easy to support new
NT35510-based panels with different initialization sequences.
This patch, preparatory for future developmentes, simplifies the
addition of new NT35510-based displays and also avoids the risk of
creating regressions on already managed panels.
Signed-off-by: Dario Binacchi <dario.binacchi at amarulasolutions.com>
---
drivers/gpu/drm/panel/panel-novatek-nt35510.c | 797 ++++--------------
1 file changed, 165 insertions(+), 632 deletions(-)
diff --git a/drivers/gpu/drm/panel/panel-novatek-nt35510.c b/drivers/gpu/drm/panel/panel-novatek-nt35510.c
index d6dceb858008..2a5a624fe447 100644
--- a/drivers/gpu/drm/panel/panel-novatek-nt35510.c
+++ b/drivers/gpu/drm/panel/panel-novatek-nt35510.c
@@ -36,126 +36,33 @@
#include <drm/drm_modes.h>
#include <drm/drm_panel.h>
-#define MCS_CMD_MAUCCTR 0xF0 /* Manufacturer command enable */
#define MCS_CMD_READ_ID1 0xDA
#define MCS_CMD_READ_ID2 0xDB
#define MCS_CMD_READ_ID3 0xDC
#define MCS_CMD_MTP_READ_SETTING 0xF8 /* Uncertain about name */
#define MCS_CMD_MTP_READ_PARAM 0xFF /* Uncertain about name */
-/*
- * These manufacturer commands are available after we enable manufacturer
- * command set (MCS) for page 0.
- */
-#define NT35510_P0_DOPCTR 0xB1
-#define NT35510_P0_SDHDTCTR 0xB6
-#define NT35510_P0_GSEQCTR 0xB7
-#define NT35510_P0_SDEQCTR 0xB8
-#define NT35510_P0_SDVPCTR 0xBA
-#define NT35510_P0_DPFRCTR1 0xBD
-#define NT35510_P0_DPFRCTR2 0xBE
-#define NT35510_P0_DPFRCTR3 0xBF
-#define NT35510_P0_DPMCTR12 0xCC
-
-#define NT35510_P0_DOPCTR_LEN 2
-#define NT35510_P0_GSEQCTR_LEN 2
-#define NT35510_P0_SDEQCTR_LEN 4
-#define NT35510_P0_SDVPCTR_LEN 1
-#define NT35510_P0_DPFRCTR1_LEN 5
-#define NT35510_P0_DPFRCTR2_LEN 5
-#define NT35510_P0_DPFRCTR3_LEN 5
-#define NT35510_P0_DPMCTR12_LEN 3
-
-#define NT35510_DOPCTR_0_RAMKP BIT(7) /* Contents kept in sleep */
-#define NT35510_DOPCTR_0_DSITE BIT(6) /* Enable TE signal */
-#define NT35510_DOPCTR_0_DSIG BIT(5) /* Enable generic read/write */
-#define NT35510_DOPCTR_0_DSIM BIT(4) /* Enable video mode on DSI */
-#define NT35510_DOPCTR_0_EOTP BIT(3) /* Support EoTP */
-#define NT35510_DOPCTR_0_N565 BIT(2) /* RGB or BGR pixel format */
-#define NT35510_DOPCTR_1_TW_PWR_SEL BIT(4) /* TE power selector */
-#define NT35510_DOPCTR_1_CRGB BIT(3) /* RGB or BGR byte order */
-#define NT35510_DOPCTR_1_CTB BIT(2) /* Vertical scanning direction */
-#define NT35510_DOPCTR_1_CRL BIT(1) /* Source driver data shift */
-#define NT35510_P0_SDVPCTR_PRG BIT(2) /* 0 = normal operation, 1 = VGLO */
-#define NT35510_P0_SDVPCTR_AVDD 0 /* source driver output = AVDD */
-#define NT35510_P0_SDVPCTR_OFFCOL 1 /* source driver output = off color */
-#define NT35510_P0_SDVPCTR_AVSS 2 /* source driver output = AVSS */
-#define NT35510_P0_SDVPCTR_HI_Z 3 /* source driver output = High impedance */
+#define _INIT_DCS_CMD(...) { \
+ .type = INIT_DCS_CMD, \
+ .len = sizeof((u8[]){__VA_ARGS__}), \
+ .data = (u8[]){__VA_ARGS__} }
-/*
- * These manufacturer commands are available after we enable manufacturer
- * command set (MCS) for page 1.
- */
-#define NT35510_P1_SETAVDD 0xB0
-#define NT35510_P1_SETAVEE 0xB1
-#define NT35510_P1_SETVCL 0xB2
-#define NT35510_P1_SETVGH 0xB3
-#define NT35510_P1_SETVRGH 0xB4
-#define NT35510_P1_SETVGL 0xB5
-#define NT35510_P1_BT1CTR 0xB6
-#define NT35510_P1_BT2CTR 0xB7
-#define NT35510_P1_BT3CTR 0xB8
-#define NT35510_P1_BT4CTR 0xB9 /* VGH boosting times/freq */
-#define NT35510_P1_BT5CTR 0xBA
-#define NT35510_P1_PFMCTR 0xBB
-#define NT35510_P1_SETVGP 0xBC
-#define NT35510_P1_SETVGN 0xBD
-#define NT35510_P1_SETVCMOFF 0xBE
-#define NT35510_P1_VGHCTR 0xBF /* VGH output ctrl */
-#define NT35510_P1_SET_GAMMA_RED_POS 0xD1
-#define NT35510_P1_SET_GAMMA_GREEN_POS 0xD2
-#define NT35510_P1_SET_GAMMA_BLUE_POS 0xD3
-#define NT35510_P1_SET_GAMMA_RED_NEG 0xD4
-#define NT35510_P1_SET_GAMMA_GREEN_NEG 0xD5
-#define NT35510_P1_SET_GAMMA_BLUE_NEG 0xD6
-
-/* AVDD and AVEE setting 3 bytes */
-#define NT35510_P1_AVDD_LEN 3
-#define NT35510_P1_AVEE_LEN 3
-#define NT35510_P1_VGH_LEN 3
-#define NT35510_P1_VGL_LEN 3
-#define NT35510_P1_VGP_LEN 3
-#define NT35510_P1_VGN_LEN 3
-/* BT1CTR thru BT5CTR setting 3 bytes */
-#define NT35510_P1_BT1CTR_LEN 3
-#define NT35510_P1_BT2CTR_LEN 3
-#define NT35510_P1_BT4CTR_LEN 3
-#define NT35510_P1_BT5CTR_LEN 3
-/* 52 gamma parameters times two per color: positive and negative */
-#define NT35510_P1_GAMMA_LEN 52
+#define _INIT_DELAY_CMD(...) { \
+ .type = DELAY_CMD,\
+ .len = sizeof((u8[]){__VA_ARGS__}), \
+ .data = (u8[]){__VA_ARGS__} }
+
+enum dsi_cmd_type {
+ INIT_DCS_CMD,
+ DELAY_CMD,
+};
+
+struct panel_init_cmd {
+ enum dsi_cmd_type type;
+ size_t len;
+ const u8 *data;
+};
-/**
- * struct nt35510_config - the display-specific NT35510 configuration
- *
- * Some of the settings provide an array of bytes, A, B C which mean:
- * A = normal / idle off mode
- * B = idle on mode
- * C = partial / idle off mode
- *
- * Gamma correction arrays are 10bit numbers, two consecutive bytes
- * makes out one point on the gamma correction curve. The points are
- * not linearly placed along the X axis, we get points 0, 1, 3, 5
- * 7, 11, 15, 23, 31, 47, 63, 95, 127, 128, 160, 192, 208, 224, 232,
- * 240, 244, 248, 250, 252, 254, 255. The voltages tuples form
- * V0, V1, V3 ... V255, with 0x0000 being the lowest voltage and
- * 0x03FF being the highest voltage.
- *
- * Each value must be strictly higher than the previous value forming
- * a rising curve like this:
- *
- * ^
- * | V255
- * | V254
- * | ....
- * | V5
- * | V3
- * | V1
- * | V0
- * +------------------------------------------->
- *
- * The details about all settings can be found in the NT35510 Application
- * Note.
- */
struct nt35510_config {
/**
* @width_mm: physical panel width [mm]
@@ -172,177 +79,90 @@ struct nt35510_config {
*/
const struct drm_display_mode mode;
/**
- * @avdd: setting for AVDD ranging from 0x00 = 6.5V to 0x14 = 4.5V
- * in 0.1V steps the default is 0x05 which means 6.0V
- */
- u8 avdd[NT35510_P1_AVDD_LEN];
- /**
- * @bt1ctr: setting for boost power control for the AVDD step-up
- * circuit (1)
- * bits 0..2 in the lower nibble controls PCK, the booster clock
- * frequency for the step-up circuit:
- * 0 = Hsync/32
- * 1 = Hsync/16
- * 2 = Hsync/8
- * 3 = Hsync/4
- * 4 = Hsync/2
- * 5 = Hsync
- * 6 = Hsync x 2
- * 7 = Hsync x 4
- * bits 4..6 in the upper nibble controls BTP, the boosting
- * amplification for the step-up circuit:
- * 0 = Disable
- * 1 = 1.5 x VDDB
- * 2 = 1.66 x VDDB
- * 3 = 2 x VDDB
- * 4 = 2.5 x VDDB
- * 5 = 3 x VDDB
- * The defaults are 4 and 4 yielding 0x44
- */
- u8 bt1ctr[NT35510_P1_BT1CTR_LEN];
- /**
- * @avee: setting for AVEE ranging from 0x00 = -6.5V to 0x14 = -4.5V
- * in 0.1V steps the default is 0x05 which means -6.0V
- */
- u8 avee[NT35510_P1_AVEE_LEN];
- /**
- * @bt2ctr: setting for boost power control for the AVEE step-up
- * circuit (2)
- * bits 0..2 in the lower nibble controls NCK, the booster clock
- * frequency, the values are the same as for PCK in @bt1ctr.
- * bits 4..5 in the upper nibble controls BTN, the boosting
- * amplification for the step-up circuit.
- * 0 = Disable
- * 1 = -1.5 x VDDB
- * 2 = -2 x VDDB
- * 3 = -2.5 x VDDB
- * 4 = -3 x VDDB
- * The defaults are 4 and 3 yielding 0x34
- */
- u8 bt2ctr[NT35510_P1_BT2CTR_LEN];
- /**
- * @vgh: setting for VGH ranging from 0x00 = 7.0V to 0x0B = 18.0V
- * in 1V steps, the default is 0x08 which means 15V
- */
- u8 vgh[NT35510_P1_VGH_LEN];
- /**
- * @bt4ctr: setting for boost power control for the VGH step-up
- * circuit (4)
- * bits 0..2 in the lower nibble controls HCK, the booster clock
- * frequency, the values are the same as for PCK in @bt1ctr.
- * bits 4..5 in the upper nibble controls BTH, the boosting
- * amplification for the step-up circuit.
- * 0 = AVDD + VDDB
- * 1 = AVDD - AVEE
- * 2 = AVDD - AVEE + VDDB
- * 3 = AVDD x 2 - AVEE
- * The defaults are 4 and 3 yielding 0x34
- */
- u8 bt4ctr[NT35510_P1_BT4CTR_LEN];
- /**
- * @vgl: setting for VGL ranging from 0x00 = -2V to 0x0f = -15V in
- * 1V steps, the default is 0x08 which means -10V
- */
- u8 vgl[NT35510_P1_VGL_LEN];
- /**
- * @bt5ctr: setting for boost power control for the VGL step-up
- * circuit (5)
- * bits 0..2 in the lower nibble controls LCK, the booster clock
- * frequency, the values are the same as for PCK in @bt1ctr.
- * bits 4..5 in the upper nibble controls BTL, the boosting
- * amplification for the step-up circuit.
- * 0 = AVEE + VCL
- * 1 = AVEE - AVDD
- * 2 = AVEE + VCL - AVDD
- * 3 = AVEE x 2 - AVDD
- * The defaults are 3 and 2 yielding 0x32
- */
- u8 bt5ctr[NT35510_P1_BT5CTR_LEN];
- /**
- * @vgp: setting for VGP, the positive gamma divider voltages
- * VGMP the high voltage and VGSP the low voltage.
- * The first byte contains bit 8 of VGMP and VGSP in bits 4 and 0
- * The second byte contains bit 0..7 of VGMP
- * The third byte contains bit 0..7 of VGSP
- * VGMP 0x00 = 3.0V .. 0x108 = 6.3V in steps of 12.5mV
- * VGSP 0x00 = 0V .. 0x111 = 3.7V in steps of 12.5mV
- */
- u8 vgp[NT35510_P1_VGP_LEN];
- /**
- * @vgn: setting for VGN, the negative gamma divider voltages,
- * same layout of bytes as @vgp.
- */
- u8 vgn[NT35510_P1_VGN_LEN];
- /**
- * @sdeqctr: Source driver control settings, first byte is
- * 0 for mode 1 and 1 for mode 2. Mode 1 uses two steps and
- * mode 2 uses three steps meaning EQS3 is not used in mode
- * 1. Mode 2 is default. The last three parameters are EQS1, EQS2
- * and EQS3, setting the rise time for each equalizer step:
- * 0x00 = 0.0 us to 0x0f = 7.5 us in steps of 0.5us. The default
- * is 0x07 = 3.5 us.
- */
- u8 sdeqctr[NT35510_P0_SDEQCTR_LEN];
- /**
- * @sdvpctr: power/voltage behaviour during vertical porch time
- */
- u8 sdvpctr;
- /**
- * @t1: the number of pixel clocks on one scanline, range
- * 0x100 (258 ticks) .. 0x3FF (1024 ticks) so the value + 1
- * clock ticks.
- */
- u16 t1;
- /**
- * @vbp: vertical back porch toward the PANEL note: not toward
- * the DSI host; these are separate interfaces, in from DSI host
- * and out to the panel.
- */
- u8 vbp;
- /**
- * @vfp: vertical front porch toward the PANEL.
- */
- u8 vfp;
+ * @lanes: number of active data lanes
+ */
+ unsigned int lanes;
/**
- * @psel: pixel clock divisor: 0 = 1, 1 = 2, 2 = 4, 3 = 8.
+ * @format: pixel format for video mode
*/
- u8 psel;
+ enum mipi_dsi_pixel_format format;
/**
- * @dpmctr12: Display timing control 12
- * Byte 1 bit 4 selects LVGL voltage level: 0 = VGLX, 1 = VGL_REG
- * Byte 1 bit 1 selects gate signal mode: 0 = non-overlap, 1 = overlap
- * Byte 1 bit 0 selects output signal control R/L swap, 0 = normal
- * 1 = swap all O->E, L->R
- * Byte 2 is CLW delay clock for CK O/E and CKB O/E signals:
- * 0x00 = 0us .. 0xFF = 12.75us in 0.05us steps
- * Byte 3 is FTI_H0 delay time for STP O/E signals:
- * 0x00 = 0us .. 0xFF = 12.75us in 0.05us steps
+ * @mode_flags: DSI operation mode related flags
*/
- u8 dpmctr12[NT35510_P0_DPMCTR12_LEN];
+ unsigned long mode_flags;
/**
- * @gamma_corr_pos_r: Red gamma correction parameters, positive
+ * @hs_rate: maximum lane frequency for high speed mode in hertz, this should
+ * be set to the real limits of the hardware, zero is only accepted for
+ * legacy drivers
*/
- u8 gamma_corr_pos_r[NT35510_P1_GAMMA_LEN];
+ unsigned long hs_rate;
/**
- * @gamma_corr_pos_g: Green gamma correction parameters, positive
+ * @lp_rate: maximum lane frequency for low power mode in hertz, this should
+ * be set to the real limits of the hardware, zero is only accepted for
+ * legacy drivers
*/
- u8 gamma_corr_pos_g[NT35510_P1_GAMMA_LEN];
+ unsigned long lp_rate;
/**
- * @gamma_corr_pos_b: Blue gamma correction parameters, positive
+ * @init_cmds: initialization command list
*/
- u8 gamma_corr_pos_b[NT35510_P1_GAMMA_LEN];
- /**
- * @gamma_corr_neg_r: Red gamma correction parameters, negative
- */
- u8 gamma_corr_neg_r[NT35510_P1_GAMMA_LEN];
- /**
- * @gamma_corr_neg_g: Green gamma correction parameters, negative
- */
- u8 gamma_corr_neg_g[NT35510_P1_GAMMA_LEN];
- /**
- * @gamma_corr_neg_b: Blue gamma correction parameters, negative
- */
- u8 gamma_corr_neg_b[NT35510_P1_GAMMA_LEN];
+ const struct panel_init_cmd *init_cmds;
+};
+
+static const struct panel_init_cmd hydis_hva40wv1_init_cmds[] = {
+ _INIT_DCS_CMD(0xF0, 0x55, 0xAA, 0x52, 0x08, 0x01),
+ _INIT_DCS_CMD(0xB0, 0x09, 0x09, 0x09),
+ _INIT_DCS_CMD(0xB6, 0x34, 0x34, 0x34),
+ _INIT_DCS_CMD(0xB1, 0x09, 0x09, 0x09),
+ _INIT_DCS_CMD(0xB7, 0x24, 0x24, 0x24),
+ _INIT_DCS_CMD(0xB3, 0x05, 0x05, 0x05),
+ _INIT_DCS_CMD(0xB9, 0x24, 0x24, 0x24),
+ _INIT_DCS_CMD(0xBF, 0x01),
+ _INIT_DCS_CMD(0xB5, 0x0B, 0x0B, 0x0B),
+ _INIT_DCS_CMD(0xBA, 0x24, 0x24, 0x24),
+ _INIT_DCS_CMD(0xBC, 0x00, 0xA3, 0x00),
+ _INIT_DCS_CMD(0xBD, 0x00, 0xA3, 0x00),
+ _INIT_DELAY_CMD(0x0A),
+ _INIT_DCS_CMD(0xD1, 0x00, 0x01, 0x00, 0x43, 0x00, 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01),
+ _INIT_DCS_CMD(0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, 0x83, 0x02, 0x78, 0x02, 0x9E),
+ _INIT_DCS_CMD(0x02, 0xDD, 0x03, 0x00, 0x03, 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03),
+ _INIT_DCS_CMD(0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE),
+ _INIT_DCS_CMD(0xD2, 0x00, 0x01, 0x00, 0x43, 0x00, 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01),
+ _INIT_DCS_CMD(0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, 0x83, 0x02, 0x78, 0x02, 0x9E),
+ _INIT_DCS_CMD(0x02, 0xDD, 0x03, 0x00, 0x03, 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03),
+ _INIT_DCS_CMD(0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE),
+ _INIT_DCS_CMD(0xD3, 0x00, 0x01, 0x00, 0x43, 0x00, 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01),
+ _INIT_DCS_CMD(0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, 0x83, 0x02, 0x78, 0x02, 0x9E),
+ _INIT_DCS_CMD(0x02, 0xDD, 0x03, 0x00, 0x03, 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03),
+ _INIT_DCS_CMD(0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE),
+ _INIT_DCS_CMD(0xD4, 0x00, 0x01, 0x00, 0x43, 0x00, 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01),
+ _INIT_DCS_CMD(0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, 0x43, 0x02, 0x50, 0x02, 0x9E),
+ _INIT_DCS_CMD(0x02, 0xDD, 0x03, 0x00, 0x03, 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03),
+ _INIT_DCS_CMD(0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE),
+ _INIT_DCS_CMD(0xD5, 0x00, 0x01, 0x00, 0x43, 0x00, 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01),
+ _INIT_DCS_CMD(0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, 0x43, 0x02, 0x50, 0x02, 0x9E),
+ _INIT_DCS_CMD(0x02, 0xDD, 0x03, 0x00, 0x03, 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03),
+ _INIT_DCS_CMD(0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE),
+ _INIT_DCS_CMD(0xD6, 0x00, 0x01, 0x00, 0x43, 0x00, 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01),
+ _INIT_DCS_CMD(0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, 0x43, 0x02, 0x50, 0x02, 0x9E),
+ _INIT_DCS_CMD(0x02, 0xDD, 0x03, 0x00, 0x03, 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03),
+ _INIT_DCS_CMD(0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE),
+ _INIT_DCS_CMD(0xF0, 0x55, 0xAA, 0x52, 0x08, 0x00),
+ _INIT_DCS_CMD(0xB1, 0x4C, 0x04),
+ _INIT_DCS_CMD(0x36, 0x02),
+ _INIT_DCS_CMD(0xB6, 0x0A),
+ _INIT_DCS_CMD(0xB7, 0x00, 0x00),
+ _INIT_DCS_CMD(0xB8, 0x01, 0x05, 0x05, 0x05),
+ _INIT_DCS_CMD(0xBA, 0x01),
+ _INIT_DCS_CMD(0xBD, 0x01, 0x84, 0x07, 0x32, 0x00),
+ _INIT_DCS_CMD(0xBE, 0x01, 0x84, 0x07, 0x31, 0x00),
+ _INIT_DCS_CMD(0xBF, 0x01, 0x84, 0x07, 0x31, 0x00),
+ _INIT_DCS_CMD(0x35, 0x00),
+ _INIT_DCS_CMD(0xCC, 0x03, 0x00, 0x00),
+ _INIT_DCS_CMD(0x11),
+ _INIT_DELAY_CMD(0x78),
+ _INIT_DCS_CMD(0x29),
+ _INIT_DELAY_CMD(0x0A),
+ {},
};
/**
@@ -379,18 +199,11 @@ static const u8 nt35510_mauc_mtp_read_param[] = { 0xAA, 0x55, 0x25, 0x01 };
static const u8 nt35510_mauc_mtp_read_setting[] = { 0x01, 0x02, 0x00, 0x20,
0x33, 0x13, 0x00, 0x40,
0x00, 0x00, 0x23, 0x02 };
-static const u8 nt35510_mauc_select_page_0[] = { 0x55, 0xAA, 0x52, 0x08, 0x00 };
-static const u8 nt35510_mauc_select_page_1[] = { 0x55, 0xAA, 0x52, 0x08, 0x01 };
-static const u8 nt35510_vgh_on[] = { 0x01 };
-
static inline struct nt35510 *panel_to_nt35510(struct drm_panel *panel)
{
return container_of(panel, struct nt35510, panel);
}
-#define NT35510_ROTATE_0_SETTING 0x02
-#define NT35510_ROTATE_180_SETTING 0x00
-
static int nt35510_send_long(struct nt35510 *nt, struct mipi_dsi_device *dsi,
u8 cmd, u8 cmdlen, const u8 *seq)
{
@@ -457,195 +270,6 @@ static int nt35510_read_id(struct nt35510 *nt)
return 0;
}
-/**
- * nt35510_setup_power() - set up power config in page 1
- * @nt: the display instance to set up
- */
-static int nt35510_setup_power(struct nt35510 *nt)
-{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
- int ret;
-
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SETAVDD,
- NT35510_P1_AVDD_LEN,
- nt->conf->avdd);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_BT1CTR,
- NT35510_P1_BT1CTR_LEN,
- nt->conf->bt1ctr);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SETAVEE,
- NT35510_P1_AVEE_LEN,
- nt->conf->avee);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_BT2CTR,
- NT35510_P1_BT2CTR_LEN,
- nt->conf->bt2ctr);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGH,
- NT35510_P1_VGH_LEN,
- nt->conf->vgh);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_BT4CTR,
- NT35510_P1_BT4CTR_LEN,
- nt->conf->bt4ctr);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_VGHCTR,
- ARRAY_SIZE(nt35510_vgh_on),
- nt35510_vgh_on);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGL,
- NT35510_P1_VGL_LEN,
- nt->conf->vgl);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_BT5CTR,
- NT35510_P1_BT5CTR_LEN,
- nt->conf->bt5ctr);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGP,
- NT35510_P1_VGP_LEN,
- nt->conf->vgp);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SETVGN,
- NT35510_P1_VGN_LEN,
- nt->conf->vgn);
- if (ret)
- return ret;
-
- /* Typically 10 ms */
- usleep_range(10000, 20000);
-
- return 0;
-}
-
-/**
- * nt35510_setup_display() - set up display config in page 0
- * @nt: the display instance to set up
- */
-static int nt35510_setup_display(struct nt35510 *nt)
-{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
- const struct nt35510_config *conf = nt->conf;
- u8 dopctr[NT35510_P0_DOPCTR_LEN];
- u8 gseqctr[NT35510_P0_GSEQCTR_LEN];
- u8 dpfrctr[NT35510_P0_DPFRCTR1_LEN];
- /* FIXME: set up any rotation (assume none for now) */
- u8 addr_mode = NT35510_ROTATE_0_SETTING;
- u8 val;
- int ret;
-
- /* Enable TE, EoTP and RGB pixel format */
- dopctr[0] = NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP |
- NT35510_DOPCTR_0_N565;
- dopctr[1] = NT35510_DOPCTR_1_CTB;
- ret = nt35510_send_long(nt, dsi, NT35510_P0_DOPCTR,
- NT35510_P0_DOPCTR_LEN,
- dopctr);
- if (ret)
- return ret;
-
- ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &addr_mode,
- sizeof(addr_mode));
- if (ret < 0)
- return ret;
-
- /*
- * Source data hold time, default 0x05 = 2.5us
- * 0x00..0x3F = 0 .. 31.5us in steps of 0.5us
- * 0x0A = 5us
- */
- val = 0x0A;
- ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &val,
- sizeof(val));
- if (ret < 0)
- return ret;
-
- /* EQ control for gate signals, 0x00 = 0 us */
- gseqctr[0] = 0x00;
- gseqctr[1] = 0x00;
- ret = nt35510_send_long(nt, dsi, NT35510_P0_GSEQCTR,
- NT35510_P0_GSEQCTR_LEN,
- gseqctr);
- if (ret)
- return ret;
-
- ret = nt35510_send_long(nt, dsi, NT35510_P0_SDEQCTR,
- NT35510_P0_SDEQCTR_LEN,
- conf->sdeqctr);
- if (ret)
- return ret;
-
- ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDVPCTR,
- &conf->sdvpctr, 1);
- if (ret < 0)
- return ret;
-
- /*
- * Display timing control for active and idle off mode:
- * the first byte contains
- * the two high bits of T1A and second byte the low 8 bits, and
- * the valid range is 0x100 (257) to 0x3ff (1023) representing
- * 258..1024 (+1) pixel clock ticks for one scanline. At 20MHz pixel
- * clock this covers the range of 12.90us .. 51.20us in steps of
- * 0.05us, the default is 0x184 (388) representing 389 ticks.
- * The third byte is VBPDA, vertical back porch display active
- * and the fourth VFPDA, vertical front porch display active,
- * both given in number of scanlines in the range 0x02..0xff
- * for 2..255 scanlines. The fifth byte is 2 bits selecting
- * PSEL for active and idle off mode, how much the 20MHz clock
- * is divided by 0..3. This needs to be adjusted to get the right
- * frame rate.
- */
- dpfrctr[0] = (conf->t1 >> 8) & 0xFF;
- dpfrctr[1] = conf->t1 & 0xFF;
- /* Vertical back porch */
- dpfrctr[2] = conf->vbp;
- /* Vertical front porch */
- dpfrctr[3] = conf->vfp;
- dpfrctr[4] = conf->psel;
- ret = nt35510_send_long(nt, dsi, NT35510_P0_DPFRCTR1,
- NT35510_P0_DPFRCTR1_LEN,
- dpfrctr);
- if (ret)
- return ret;
- /* For idle and partial idle off mode we decrease front porch by one */
- dpfrctr[3]--;
- ret = nt35510_send_long(nt, dsi, NT35510_P0_DPFRCTR2,
- NT35510_P0_DPFRCTR2_LEN,
- dpfrctr);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P0_DPFRCTR3,
- NT35510_P0_DPFRCTR3_LEN,
- dpfrctr);
- if (ret)
- return ret;
-
- /* Enable TE on vblank */
- ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
- if (ret)
- return ret;
-
- /* Turn on the pads? */
- ret = nt35510_send_long(nt, dsi, NT35510_P0_DPMCTR12,
- NT35510_P0_DPMCTR12_LEN,
- conf->dpmctr12);
- if (ret)
- return ret;
-
- return 0;
-}
-
static int nt35510_set_brightness(struct backlight_device *bl)
{
struct nt35510 *nt = bl_get_data(bl);
@@ -672,7 +296,6 @@ static const struct backlight_ops nt35510_bl_ops = {
*/
static int nt35510_power_on(struct nt35510 *nt)
{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
int ret;
ret = regulator_bulk_enable(ARRAY_SIZE(nt->supplies), nt->supplies);
@@ -694,73 +317,6 @@ static int nt35510_power_on(struct nt35510 *nt)
usleep_range(120000, 140000);
}
- ret = nt35510_send_long(nt, dsi, MCS_CMD_MTP_READ_PARAM,
- ARRAY_SIZE(nt35510_mauc_mtp_read_param),
- nt35510_mauc_mtp_read_param);
- if (ret)
- return ret;
-
- ret = nt35510_send_long(nt, dsi, MCS_CMD_MTP_READ_SETTING,
- ARRAY_SIZE(nt35510_mauc_mtp_read_setting),
- nt35510_mauc_mtp_read_setting);
- if (ret)
- return ret;
-
- nt35510_read_id(nt);
-
- /* Set up stuff in manufacturer control, page 1 */
- ret = nt35510_send_long(nt, dsi, MCS_CMD_MAUCCTR,
- ARRAY_SIZE(nt35510_mauc_select_page_1),
- nt35510_mauc_select_page_1);
- if (ret)
- return ret;
-
- ret = nt35510_setup_power(nt);
- if (ret)
- return ret;
-
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_RED_POS,
- NT35510_P1_GAMMA_LEN,
- nt->conf->gamma_corr_pos_r);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_GREEN_POS,
- NT35510_P1_GAMMA_LEN,
- nt->conf->gamma_corr_pos_g);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_BLUE_POS,
- NT35510_P1_GAMMA_LEN,
- nt->conf->gamma_corr_pos_b);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_RED_NEG,
- NT35510_P1_GAMMA_LEN,
- nt->conf->gamma_corr_neg_r);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_GREEN_NEG,
- NT35510_P1_GAMMA_LEN,
- nt->conf->gamma_corr_neg_g);
- if (ret)
- return ret;
- ret = nt35510_send_long(nt, dsi, NT35510_P1_SET_GAMMA_BLUE_NEG,
- NT35510_P1_GAMMA_LEN,
- nt->conf->gamma_corr_neg_b);
- if (ret)
- return ret;
-
- /* Set up stuff in manufacturer control, page 0 */
- ret = nt35510_send_long(nt, dsi, MCS_CMD_MAUCCTR,
- ARRAY_SIZE(nt35510_mauc_select_page_0),
- nt35510_mauc_select_page_0);
- if (ret)
- return ret;
-
- ret = nt35510_setup_display(nt);
- if (ret)
- return ret;
-
return 0;
}
@@ -808,6 +364,44 @@ static int nt35510_unprepare(struct drm_panel *panel)
return 0;
}
+static int nt35510_init(struct nt35510 *nt)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
+ const struct panel_init_cmd *cmds = nt->conf->init_cmds;
+ int i, ret;
+
+ if (!cmds) {
+ dev_warn(nt->dev, "empty initialization command list\n");
+ return 0;
+ }
+
+ for (i = 0; cmds[i].len != 0; i++) {
+ const struct panel_init_cmd *cmd = &cmds[i];
+
+ switch (cmd->type) {
+ case DELAY_CMD:
+ msleep(cmd->data[0]);
+ ret = 0;
+ break;
+ case INIT_DCS_CMD:
+ ret = nt35510_send_long(nt, dsi, cmd->data[0],
+ cmd->len - 1,
+ cmd->len <= 1 ? NULL :
+ &cmd->data[1]);
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ if (ret < 0) {
+ dev_err(nt->dev, "failed to write command %u\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
static int nt35510_prepare(struct drm_panel *panel)
{
struct nt35510 *nt = panel_to_nt35510(panel);
@@ -818,24 +412,21 @@ static int nt35510_prepare(struct drm_panel *panel)
if (ret)
return ret;
- /* Exit sleep mode */
- ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
- if (ret) {
- dev_err(nt->dev, "failed to exit sleep mode (%d)\n", ret);
+ ret = nt35510_send_long(nt, dsi, MCS_CMD_MTP_READ_PARAM,
+ ARRAY_SIZE(nt35510_mauc_mtp_read_param),
+ nt35510_mauc_mtp_read_param);
+ if (ret)
return ret;
- }
- /* Up to 120 ms */
- usleep_range(120000, 150000);
- ret = mipi_dsi_dcs_set_display_on(dsi);
- if (ret) {
- dev_err(nt->dev, "failed to turn display on (%d)\n", ret);
+ ret = nt35510_send_long(nt, dsi, MCS_CMD_MTP_READ_SETTING,
+ ARRAY_SIZE(nt35510_mauc_mtp_read_setting),
+ nt35510_mauc_mtp_read_setting);
+ if (ret)
return ret;
- }
- /* Some 10 ms */
- usleep_range(10000, 20000);
- return 0;
+ nt35510_read_id(nt);
+
+ return nt35510_init(nt);
}
static int nt35510_get_modes(struct drm_panel *panel,
@@ -878,25 +469,6 @@ static int nt35510_probe(struct mipi_dsi_device *dsi)
nt = devm_kzalloc(dev, sizeof(struct nt35510), GFP_KERNEL);
if (!nt)
return -ENOMEM;
- mipi_dsi_set_drvdata(dsi, nt);
- nt->dev = dev;
-
- dsi->lanes = 2;
- dsi->format = MIPI_DSI_FMT_RGB888;
- /*
- * Datasheet suggests max HS rate for NT35510 is 250 MHz
- * (period time 4ns, see figure 7.6.4 page 365) and max LP rate is
- * 20 MHz (period time 50ns, see figure 7.6.6. page 366).
- * However these frequencies appear in source code for the Hydis
- * HVA40WV1 panel and setting up the LP frequency makes the panel
- * not work.
- *
- * TODO: if other panels prove to be closer to the datasheet,
- * maybe make this a per-panel config in struct nt35510_config?
- */
- dsi->hs_rate = 349440000;
- dsi->lp_rate = 9600000;
- dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS;
/*
* Every new incarnation of this display must have a unique
@@ -908,6 +480,15 @@ static int nt35510_probe(struct mipi_dsi_device *dsi)
return -ENODEV;
}
+ mipi_dsi_set_drvdata(dsi, nt);
+ nt->dev = dev;
+
+ dsi->lanes = nt->conf->lanes;
+ dsi->format = nt->conf->format;
+ dsi->hs_rate = nt->conf->hs_rate;
+ dsi->lp_rate = nt->conf->lp_rate;
+ dsi->mode_flags = nt->conf->mode_flags;
+
nt->supplies[0].supply = "vdd"; /* 2.3-4.8 V */
nt->supplies[1].supply = "vddi"; /* 1.65-3.3V */
ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(nt->supplies),
@@ -980,27 +561,6 @@ static void nt35510_remove(struct mipi_dsi_device *dsi)
drm_panel_remove(&nt->panel);
}
-/*
- * These gamma correction values are 10bit tuples, so only bits 0 and 1 is
- * ever used in the first byte. They form a positive and negative gamma
- * correction curve for each color, values must be strictly higher for each
- * step on the curve. As can be seen these default curves goes from 0x0001
- * to 0x03FE.
- */
-#define NT35510_GAMMA_POS_DEFAULT 0x00, 0x01, 0x00, 0x43, 0x00, \
- 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01, \
- 0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, \
- 0x83, 0x02, 0x78, 0x02, 0x9E, 0x02, 0xDD, 0x03, 0x00, 0x03, \
- 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03, \
- 0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE
-
-#define NT35510_GAMMA_NEG_DEFAULT 0x00, 0x01, 0x00, 0x43, 0x00, \
- 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01, \
- 0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, \
- 0x43, 0x02, 0x50, 0x02, 0x9E, 0x02, 0xDD, 0x03, 0x00, 0x03, \
- 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03, \
- 0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE
-
/*
* The Hydis HVA40WV1 panel
*/
@@ -1030,47 +590,20 @@ static const struct nt35510_config nt35510_hydis_hva40wv1 = {
.vtotal = 800 + 2 + 0 + 5, /* VBP = 5 */
.flags = 0,
},
- /* 0x09: AVDD = 5.6V */
- .avdd = { 0x09, 0x09, 0x09 },
- /* 0x34: PCK = Hsync/2, BTP = 2 x VDDB */
- .bt1ctr = { 0x34, 0x34, 0x34 },
- /* 0x09: AVEE = -5.6V */
- .avee = { 0x09, 0x09, 0x09 },
- /* 0x24: NCK = Hsync/2, BTN = -2 x VDDB */
- .bt2ctr = { 0x24, 0x24, 0x24 },
- /* 0x05 = 12V */
- .vgh = { 0x05, 0x05, 0x05 },
- /* 0x24: NCKA = Hsync/2, VGH = 2 x AVDD - AVEE */
- .bt4ctr = { 0x24, 0x24, 0x24 },
- /* 0x0B = -13V */
- .vgl = { 0x0B, 0x0B, 0x0B },
- /* 0x24: LCKA = Hsync, VGL = AVDD + VCL - AVDD */
- .bt5ctr = { 0x24, 0x24, 0x24 },
- /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
- .vgp = { 0x00, 0xA3, 0x00 },
- /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
- .vgn = { 0x00, 0xA3, 0x00 },
- /* SDEQCTR: source driver EQ mode 2, 2.5 us rise time on each step */
- .sdeqctr = { 0x01, 0x05, 0x05, 0x05 },
- /* SDVPCTR: Normal operation off color during v porch */
- .sdvpctr = 0x01,
- /* T1: number of pixel clocks on one scanline: 0x184 = 389 clocks */
- .t1 = 0x0184,
- /* VBP: vertical back porch toward the panel */
- .vbp = 7,
- /* VFP: vertical front porch toward the panel */
- .vfp = 50,
- /* PSEL: divide pixel clock 20MHz with 1 (no clock downscaling) */
- .psel = 0,
- /* DPTMCTR12: 0x03: LVGL = VGLX, overlap mode, swap R->L O->E */
- .dpmctr12 = { 0x03, 0x00, 0x00, },
- /* Default gamma correction values */
- .gamma_corr_pos_r = { NT35510_GAMMA_POS_DEFAULT },
- .gamma_corr_pos_g = { NT35510_GAMMA_POS_DEFAULT },
- .gamma_corr_pos_b = { NT35510_GAMMA_POS_DEFAULT },
- .gamma_corr_neg_r = { NT35510_GAMMA_NEG_DEFAULT },
- .gamma_corr_neg_g = { NT35510_GAMMA_NEG_DEFAULT },
- .gamma_corr_neg_b = { NT35510_GAMMA_NEG_DEFAULT },
+ .mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS,
+ .lanes = 2,
+ .format = MIPI_DSI_FMT_RGB888,
+ /*
+ * Datasheet suggests max HS rate for NT35510 is 250 MHz
+ * (period time 4ns, see figure 7.6.4 page 365) and max LP rate is
+ * 20 MHz (period time 50ns, see figure 7.6.6. page 366).
+ * However these frequencies appear in source code for the Hydis
+ * HVA40WV1 panel and setting up the LP frequency makes the panel
+ * not work.
+ */
+ .hs_rate = 349440000,
+ .lp_rate = 9600000,
+ .init_cmds = hydis_hva40wv1_init_cmds,
};
static const struct of_device_id nt35510_of_match[] = {
--
2.43.0
More information about the dri-devel
mailing list