[PATCH v3 0/3] drm/rockchip: dw_hdmi: Add 4k at 30 support

Sascha Hauer s.hauer at pengutronix.de
Fri Feb 3 13:09:43 UTC 2023


Hi,

On Wed, Feb 01, 2023 at 09:23:56AM +0900, FUKAUMI Naoki wrote:
> hi,
> 
> I'm trying this patch series with 6.1.x kernel. it works fine on rk356x
> based boards (ROCK 3), but it has a problem on rk3399 boards (ROCK 4).
> 
> on rk3399 with this patch, I can see large noise area (about one third right
> side of the screen) at 4k at 30. 1080p works fine as same as before.
> 
> can someone reproduce this problem on rk3399?

I have a RK339 board here, I can try to reproduce this next week. Of
course I have no idea what the issue might be, in the downstream Kernel
I can't find anything that is handled specially for the RK3399.

What might be worth checking is the VOP clock rate. Does the VOP clock
in /sys/kernel/debug/clk/clk_summary (I don't know which one it is
though) match the pixelclock?

If nothing else helps I can change the code to only allow the higher
resolutions on RK3568 where we know it works.

Sascha

> 
> --
> FUKAUMI Naoki
> 
> On 1/31/23 17:09, Sascha Hauer wrote:
> > Heiko, Sandy,
> > 
> > Ok to apply these patches?
> > 
> > Sascha
> > 
> > On Wed, Jan 18, 2023 at 02:22:10PM +0100, Sascha Hauer wrote:
> > > It's been some time since I last sent this series. This version fixes
> > > a regression Dan Johansen reported. The reason turned out to be simple,
> > > I used the YUV420 register values instead of the RGB ones.
> > > 
> > > I realized that we cannot achieve several modes offered by my monitor
> > > as these require pixelclocks that are slightly below the standard
> > > pixelclocks. As these are lower than the standard clock rates the PLL
> > > driver offers the clk driver falls back to a way lower frequency
> > > which results in something the monitor can't display, so this series
> > > now contains a patch to discard these unachievable modes.
> > > 
> > > Sascha
> > > 
> > > Changes since v2:
> > > - Use correct register values for mpll_cfg
> > > - Add patch to discard modes we cannot achieve
> > > 
> > > Changes since v1:
> > > - Allow non standard clock rates only on Synopsys phy as suggested by
> > >    Robin Murphy
> > > 
> > > Sascha Hauer (3):
> > >    drm/rockchip: dw_hdmi: relax mode_valid hook
> > >    drm/rockchip: dw_hdmi: Add support for 4k at 30 resolution
> > >    drm/rockchip: dw_hdmi: discard modes with unachievable pixelclocks
> > > 
> > >   drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c | 40 ++++++++++++++++-----
> > >   1 file changed, 32 insertions(+), 8 deletions(-)
> > > 
> > > -- 
> > > 2.30.2
> > > 
> > > 
> > 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |


More information about the dri-devel mailing list