[PATCH v3 4/6] arm64: dts: qcom: sm8350: finish reordering nodes
Konrad Dybcio
konrad.dybcio at linaro.org
Fri Feb 10 11:09:03 UTC 2023
On 9.02.2023 14:38, Dmitry Baryshkov wrote:
> Finish reordering DT nodes by their address. Move PDC, tsens, AOSS,
> SRAM, SPMI and TLMM nodes to the proper position.
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
> ---
[...]
> + phys = <&mdss_dsi1_phy>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "disabled";
> +
> + dsi1_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + /* TODO: opp-187500000 should work with
> + * &rpmhpd_opp_low_svs, but one some of
> + * sm8350_hdk boards reboot using this
> + * opp.
> + */
It's not a part of this patch, but an idea came into my
head.. could you check with socid that your HDK has an
8350v2.1?
As for the patch itself.. I *think* I don't see anything
wrong..
Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
Konrad
> + opp-187500000 {
> + opp-hz = /bits/ 64 <187500000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-300000000 {
> + opp-hz = /bits/ 64 <300000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-358000000 {
> + opp-hz = /bits/ 64 <358000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + mdss_dsi1_in: endpoint {
> + remote-endpoint = <&dpu_intf2_out>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + mdss_dsi1_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + mdss_dsi1_phy: phy at ae96400 {
> + compatible = "qcom,sm8350-dsi-phy-5nm";
> + reg = <0 0x0ae96400 0 0x200>,
> + <0 0x0ae96600 0 0x280>,
> + <0 0x0ae96900 0 0x27c>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> +
> + status = "disabled";
> + };
> + };
> +
> + dispcc: clock-controller at af00000 {
> + compatible = "qcom,sm8350-dispcc";
> + reg = <0 0x0af00000 0 0x10000>;
> + clocks = <&rpmhcc RPMH_CXO_CLK>,
> + <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>,
> + <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>,
> + <0>,
> + <0>;
> + clock-names = "bi_tcxo",
> + "dsi0_phy_pll_out_byteclk",
> + "dsi0_phy_pll_out_dsiclk",
> + "dsi1_phy_pll_out_byteclk",
> + "dsi1_phy_pll_out_dsiclk",
> + "dp_phy_pll_link_clk",
> + "dp_phy_pll_vco_div_clk";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> +
> + power-domains = <&rpmhpd SM8350_MMCX>;
> + };
> +
> + pdc: interrupt-controller at b220000 {
> + compatible = "qcom,sm8350-pdc", "qcom,pdc";
> + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>,
> + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>,
> + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>,
> + <156 716 12>;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&intc>;
> + interrupt-controller;
> + };
> +
> + tsens0: thermal-sensor at c263000 {
> + compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
> + reg = <0 0x0c263000 0 0x1ff>, /* TM */
> + <0 0x0c222000 0 0x8>; /* SROT */
> + #qcom,sensors = <15>;
> + interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
> + <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + tsens1: thermal-sensor at c265000 {
> + compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
> + reg = <0 0x0c265000 0 0x1ff>, /* TM */
> + <0 0x0c223000 0 0x8>; /* SROT */
> + #qcom,sensors = <14>;
> + interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
> + <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + aoss_qmp: power-management at c300000 {
> + compatible = "qcom,sm8350-aoss-qmp", "qcom,aoss-qmp";
> + reg = <0 0x0c300000 0 0x400>;
> + interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + #clock-cells = <0>;
> + };
> +
> + sram at c3f0000 {
> + compatible = "qcom,rpmh-stats";
> + reg = <0 0x0c3f0000 0 0x400>;
> + };
> +
> + spmi_bus: spmi at c440000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0 0x0c440000 0x0 0x1100>,
> + <0x0 0x0c600000 0x0 0x2000000>,
> + <0x0 0x0e600000 0x0 0x100000>,
> + <0x0 0x0e700000 0x0 0xa0000>,
> + <0x0 0x0c40a000 0x0 0x26000>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + };
> +
> + tlmm: pinctrl at f100000 {
> + compatible = "qcom,sm8350-tlmm";
> + reg = <0 0x0f100000 0 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-ranges = <&tlmm 0 0 204>;
> + wakeup-parent = <&pdc>;
> +
> + sdc2_default_state: sdc2-default-state {
> + clk-pins {
> + pins = "sdc2_clk";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + cmd-pins {
> + pins = "sdc2_cmd";
> + drive-strength = <16>;
> + bias-pull-up;
> + };
> +
> + data-pins {
> + pins = "sdc2_data";
> + drive-strength = <16>;
> + bias-pull-up;
> + };
> + };
> +
> + sdc2_sleep_state: sdc2-sleep-state {
> + clk-pins {
> + pins = "sdc2_clk";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> - <&rpmhcc RPMH_CXO_CLK>;
> - clock-names = "iface", "ref";
> + cmd-pins {
> + pins = "sdc2_cmd";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - status = "disabled";
> + data-pins {
> + pins = "sdc2_data";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> };
>
> - mdss_dsi1: dsi at ae96000 {
> - compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
> - reg = <0 0x0ae96000 0 0x400>;
> - reg-names = "dsi_ctrl";
> + qup_uart3_default_state: qup-uart3-default-state {
> + rx-pins {
> + pins = "gpio18";
> + function = "qup3";
> + };
> + tx-pins {
> + pins = "gpio19";
> + function = "qup3";
> + };
> + };
>
> - interrupt-parent = <&mdss>;
> - interrupts = <5>;
> + qup_uart6_default: qup-uart6-default-state {
> + pins = "gpio30", "gpio31";
> + function = "qup6";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
> - <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
> - <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
> - <&dispcc DISP_CC_MDSS_ESC1_CLK>,
> - <&dispcc DISP_CC_MDSS_AHB_CLK>,
> - <&gcc GCC_DISP_HF_AXI_CLK>;
> - clock-names = "byte",
> - "byte_intf",
> - "pixel",
> - "core",
> - "iface",
> - "bus";
> + qup_uart18_default: qup-uart18-default-state {
> + pins = "gpio58", "gpio59";
> + function = "qup18";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
> - <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
> - assigned-clock-parents = <&mdss_dsi1_phy 0>,
> - <&mdss_dsi1_phy 1>;
> + qup_i2c0_default: qup-i2c0-default-state {
> + pins = "gpio4", "gpio5";
> + function = "qup0";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - operating-points-v2 = <&dsi1_opp_table>;
> - power-domains = <&rpmhpd SM8350_MMCX>;
> + qup_i2c1_default: qup-i2c1-default-state {
> + pins = "gpio8", "gpio9";
> + function = "qup1";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - phys = <&mdss_dsi1_phy>;
> + qup_i2c2_default: qup-i2c2-default-state {
> + pins = "gpio12", "gpio13";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - #address-cells = <1>;
> - #size-cells = <0>;
> + qup_i2c4_default: qup-i2c4-default-state {
> + pins = "gpio20", "gpio21";
> + function = "qup4";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - status = "disabled";
> + qup_i2c5_default: qup-i2c5-default-state {
> + pins = "gpio24", "gpio25";
> + function = "qup5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - dsi1_opp_table: opp-table {
> - compatible = "operating-points-v2";
> + qup_i2c6_default: qup-i2c6-default-state {
> + pins = "gpio28", "gpio29";
> + function = "qup6";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - /* TODO: opp-187500000 should work with
> - * &rpmhpd_opp_low_svs, but one some of
> - * sm8350_hdk boards reboot using this
> - * opp.
> - */
> - opp-187500000 {
> - opp-hz = /bits/ 64 <187500000>;
> - required-opps = <&rpmhpd_opp_svs>;
> - };
> + qup_i2c7_default: qup-i2c7-default-state {
> + pins = "gpio32", "gpio33";
> + function = "qup7";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - opp-300000000 {
> - opp-hz = /bits/ 64 <300000000>;
> - required-opps = <&rpmhpd_opp_svs>;
> - };
> + qup_i2c8_default: qup-i2c8-default-state {
> + pins = "gpio36", "gpio37";
> + function = "qup8";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - opp-358000000 {
> - opp-hz = /bits/ 64 <358000000>;
> - required-opps = <&rpmhpd_opp_svs_l1>;
> - };
> - };
> + qup_i2c9_default: qup-i2c9-default-state {
> + pins = "gpio40", "gpio41";
> + function = "qup9";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> + qup_i2c10_default: qup-i2c10-default-state {
> + pins = "gpio44", "gpio45";
> + function = "qup10";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - port at 0 {
> - reg = <0>;
> - mdss_dsi1_in: endpoint {
> - remote-endpoint = <&dpu_intf2_out>;
> - };
> - };
> + qup_i2c11_default: qup-i2c11-default-state {
> + pins = "gpio48", "gpio49";
> + function = "qup11";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - port at 1 {
> - reg = <1>;
> - mdss_dsi1_out: endpoint {
> - };
> - };
> - };
> + qup_i2c12_default: qup-i2c12-default-state {
> + pins = "gpio52", "gpio53";
> + function = "qup12";
> + drive-strength = <2>;
> + bias-pull-up;
> };
>
> - mdss_dsi1_phy: phy at ae96400 {
> - compatible = "qcom,sm8350-dsi-phy-5nm";
> - reg = <0 0x0ae96400 0 0x200>,
> - <0 0x0ae96600 0 0x280>,
> - <0 0x0ae96900 0 0x27c>;
> - reg-names = "dsi_phy",
> - "dsi_phy_lane",
> - "dsi_pll";
> + qup_i2c13_default: qup-i2c13-default-state {
> + pins = "gpio0", "gpio1";
> + function = "qup13";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
>
> - #clock-cells = <1>;
> - #phy-cells = <0>;
> + qup_i2c14_default: qup-i2c14-default-state {
> + pins = "gpio56", "gpio57";
> + function = "qup14";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> - <&rpmhcc RPMH_CXO_CLK>;
> - clock-names = "iface", "ref";
> + qup_i2c15_default: qup-i2c15-default-state {
> + pins = "gpio60", "gpio61";
> + function = "qup15";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - status = "disabled";
> + qup_i2c16_default: qup-i2c16-default-state {
> + pins = "gpio64", "gpio65";
> + function = "qup16";
> + drive-strength = <2>;
> + bias-disable;
> };
> - };
>
> - dispcc: clock-controller at af00000 {
> - compatible = "qcom,sm8350-dispcc";
> - reg = <0 0x0af00000 0 0x10000>;
> - clocks = <&rpmhcc RPMH_CXO_CLK>,
> - <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>,
> - <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>,
> - <0>,
> - <0>;
> - clock-names = "bi_tcxo",
> - "dsi0_phy_pll_out_byteclk",
> - "dsi0_phy_pll_out_dsiclk",
> - "dsi1_phy_pll_out_byteclk",
> - "dsi1_phy_pll_out_dsiclk",
> - "dp_phy_pll_link_clk",
> - "dp_phy_pll_vco_div_clk";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - #power-domain-cells = <1>;
> + qup_i2c17_default: qup-i2c17-default-state {
> + pins = "gpio72", "gpio73";
> + function = "qup17";
> + drive-strength = <2>;
> + bias-disable;
> + };
>
> - power-domains = <&rpmhpd SM8350_MMCX>;
> + qup_i2c19_default: qup-i2c19-default-state {
> + pins = "gpio76", "gpio77";
> + function = "qup19";
> + drive-strength = <2>;
> + bias-disable;
> + };
> };
>
> apps_smmu: iommu at 15000000 {
More information about the dri-devel
mailing list