[PATCH 5/6] drm/msm/dsi: add support for DSI-PHY on SM8550
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Wed Jan 4 17:20:46 UTC 2023
On Wed, 4 Jan 2023 at 12:11, Neil Armstrong <neil.armstrong at linaro.org> wrote:
>
> On 04/01/2023 10:53, Dmitry Baryshkov wrote:
> > On 04/01/2023 11:08, Neil Armstrong wrote:
> >> SM8550 use a 4nm DSI PHYs, which share register definitions
> >> with 7nm DSI PHYs. Rather than duplicating the driver, handle
> >> 4nm variant inside the common 5+7nm driver.
> >>
> >> Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
> >> ---
> >> drivers/gpu/drm/msm/Kconfig | 4 +-
> >> drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 2 +
> >> drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 1 +
> >> drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c | 102 ++++++++++++++++++++++++------
> >> 4 files changed, 89 insertions(+), 20 deletions(-)
> >>
> >> diff --git a/drivers/gpu/drm/msm/Kconfig b/drivers/gpu/drm/msm/Kconfig
> >> index e7b100d97f88..949b18a29a55 100644
> >> --- a/drivers/gpu/drm/msm/Kconfig
> >> +++ b/drivers/gpu/drm/msm/Kconfig
> >> @@ -140,11 +140,11 @@ config DRM_MSM_DSI_10NM_PHY
> >> Choose this option if DSI PHY on SDM845 is used on the platform.
> >> config DRM_MSM_DSI_7NM_PHY
> >> - bool "Enable DSI 7nm/5nm PHY driver in MSM DRM"
> >> + bool "Enable DSI 7nm/5nm/4nm PHY driver in MSM DRM"
> >> depends on DRM_MSM_DSI
> >> default y
> >> help
> >> - Choose this option if DSI PHY on SM8150/SM8250/SM8350/SM8450/SC7280
> >> + Choose this option if DSI PHY on SM8150/SM8250/SM8350/SM8450/SM8550/SC7280
> >> is used on the platform.
> >> config DRM_MSM_HDMI
> >> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> >> index 0c956fdab23e..54e03cc9fbe7 100644
> >> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> >> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> >> @@ -573,6 +573,8 @@ static const struct of_device_id dsi_phy_dt_match[] = {
> >> .data = &dsi_phy_5nm_8350_cfgs },
> >> { .compatible = "qcom,dsi-phy-5nm-8450",
> >> .data = &dsi_phy_5nm_8450_cfgs },
> >> + { .compatible = "qcom,dsi-phy-4nm-8550",
> >> + .data = &dsi_phy_4nm_8550_cfgs },
> >> #endif
> >> {}
> >> };
> >> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
> >> index f7a907ed2b4b..58f9e09f5224 100644
> >> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
> >> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
> >> @@ -59,6 +59,7 @@ extern const struct msm_dsi_phy_cfg dsi_phy_7nm_8150_cfgs;
> >> extern const struct msm_dsi_phy_cfg dsi_phy_7nm_7280_cfgs;
> >> extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8350_cfgs;
> >> extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8450_cfgs;
> >> +extern const struct msm_dsi_phy_cfg dsi_phy_4nm_8550_cfgs;
> >> struct msm_dsi_dphy_timing {
> >> u32 clk_zero;
> >> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
> >> index 7b2c16b3a36c..11629c431c30 100644
> >> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
> >> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
> >> @@ -47,6 +47,8 @@
> >> #define DSI_PHY_7NM_QUIRK_V4_2 BIT(2)
> >> /* Hardware is V4.3 */
> >> #define DSI_PHY_7NM_QUIRK_V4_3 BIT(3)
> >> +/* Hardware is V5.2 */
> >> +#define DSI_PHY_7NM_QUIRK_V5_2 BIT(4)
> >> struct dsi_pll_config {
> >> bool enable_ssc;
> >> @@ -124,14 +126,25 @@ static void dsi_pll_calc_dec_frac(struct dsi_pll_7nm *pll, struct dsi_pll_config
> >> if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1)
> >> config->pll_clock_inverters = 0x28;
> >> - else if (pll_freq <= 1000000000ULL)
> >> - config->pll_clock_inverters = 0xa0;
> >> - else if (pll_freq <= 2500000000ULL)
> >> - config->pll_clock_inverters = 0x20;
> >> - else if (pll_freq <= 3020000000ULL)
> >> - config->pll_clock_inverters = 0x00;
> >> - else
> >> - config->pll_clock_inverters = 0x40;
> >> + else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
> >> + if (pll_freq <= 1300000000ULL)
> >> + config->pll_clock_inverters = 0xa0;
> >> + else if (pll_freq <= 2500000000ULL)
> >> + config->pll_clock_inverters = 0x20;
> >> + else if (pll_freq <= 4000000000ULL)
> >> + config->pll_clock_inverters = 0x00;
> >> + else
> >> + config->pll_clock_inverters = 0x40;
> >> + } else {
> >> + if (pll_freq <= 1000000000ULL)
> >> + config->pll_clock_inverters = 0xa0;
> >> + else if (pll_freq <= 2500000000ULL)
> >> + config->pll_clock_inverters = 0x20;
> >> + else if (pll_freq <= 3020000000ULL)
> >> + config->pll_clock_inverters = 0x00;
> >> + else
> >> + config->pll_clock_inverters = 0x40;
> >> + }
> >> config->decimal_div_start = dec;
> >> config->frac_div_start = frac;
> >> @@ -222,6 +235,13 @@ static void dsi_pll_config_hzindep_reg(struct dsi_pll_7nm *pll)
> >> vco_config_1 = 0x01;
> >> }
> >> + if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
> >> + if (pll->vco_current_rate < 1557000000ULL)
> >> + vco_config_1 = 0x08;
> >> + else
> >> + vco_config_1 = 0x01;
> >> + }
> >> +
> >> dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_ANALOG_CONTROLS_FIVE_1,
> >> analog_controls_five_1);
> >> dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_VCO_CONFIG_1, vco_config_1);
> >> @@ -860,7 +880,8 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
> >> pr_warn("PLL turned on before configuring PHY\n");
> >> /* Request for REFGEN READY */
> >> - if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) {
> >> + if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) ||
> >> + (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
> >> dsi_phy_write(phy->base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10, 0x1);
> >> udelay(500);
> >> }
> >> @@ -881,20 +902,38 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
> >> glbl_str_swi_cal_sel_ctrl = 0x00;
> >> if (phy->cphy_mode) {
> >> - vreg_ctrl_0 = 0x51;
> >> - vreg_ctrl_1 = 0x55;
> >> + if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
> >> + vreg_ctrl_0 = 0x45;
> >> + vreg_ctrl_1 = 0x45;
> >> + } else {
> >> + vreg_ctrl_0 = 0x51;
> >> + vreg_ctrl_1 = 0x55;
> >> + }
> >
> > Please move these quirk-specific values down, to the rest of if (QUIRK_5_2) statement.
>
> Ok
>
> >
> >> glbl_hstx_str_ctrl_0 = 0x00;
> >> glbl_pemph_ctrl_0 = 0x11;
> >> lane_ctrl0 = 0x17;
> >> } else {
> >> - vreg_ctrl_0 = less_than_1500_mhz ? 0x53 : 0x52;
> >> - vreg_ctrl_1 = 0x5c;
> >> + if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
> >> + vreg_ctrl_0 = 0x44;
> >> + vreg_ctrl_1 = 0x19;
> >> + } else {
> >> + vreg_ctrl_0 = less_than_1500_mhz ? 0x53 : 0x52;
> >> + vreg_ctrl_1 = 0x5c;
> >> + }
> >> glbl_hstx_str_ctrl_0 = 0x88;
> >> glbl_pemph_ctrl_0 = 0x00;
> >> lane_ctrl0 = 0x1f;
> >> }
> >> - if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) {
> >> + if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
> >> + if (phy->cphy_mode) {
> >> + glbl_rescode_top_ctrl = 0x00;
> >> + glbl_rescode_bot_ctrl = 0x00;
> >> + } else {
> >> + glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3c : 0x03;
> >> + glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x3c;
> >> + }
> >> + } else if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3)) {
> >> if (phy->cphy_mode) {
> >> glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d : 0x01;
> >> glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x3b;
> >> @@ -943,9 +982,8 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
> >> dsi_phy_write(base + REG_DSI_7nm_PHY_CMN_RBUF_CTRL, 0x00);
> >> /* program CMN_CTRL_4 for minor_ver 2 chipsets*/
> >> - data = dsi_phy_read(base + REG_DSI_7nm_PHY_CMN_REVISION_ID0);
> >> - data = data & (0xf0);
> >> - if (data == 0x20)
> >> + if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
> >> + (dsi_phy_read(base + REG_DSI_7nm_PHY_CMN_REVISION_ID0) & (0xf0)) == 0x20)
> >> dsi_phy_write(base + REG_DSI_7nm_PHY_CMN_CTRL_4, 0x04);
> >
> > Ugh. I should change this statement to use quirks too.
>
> Sorrt I don't see what you mean, should I change the original REVISION_ID0 to a proper quirk ?
>
No, I'll do this. For now you can leave this piece code as is (reading
rev + your quirk).
--
With best wishes
Dmitry
More information about the dri-devel
mailing list