linux-6.2-rc4+ hangs on poweroff/reboot: Bisected

[Chris Clayton]

[Resend because the mail client on my phone decided to turn HTML on behind my back, so my reply got bounced.]

Thanks Thorsten.

I did try to revert but it didnt revert cleanly and I don't have the knowledge to fix it up.

The patch was part of a merge that included a number of related patches. Tomorrow, I'll try to revert the lot and report
back.

Chris



On 27/01/2023 11:20, Linux kernel regression tracking (Thorsten Leemhuis) wrote:
> Hi, this is your Linux kernel regression tracker. Top-posting for once,
> to make this easily accessible to everyone.
> 
> @nouveau-maintainers, did anyone take a look at this? The report is
> already 8 days old and I don't see a single reply. Sure, we'll likely
> get a -rc8, but still it would be good to not fix this on the finish line.
> 
> Chris, btw, did you try if you can revert the commit on top of latest
> mainline? And if so, does it fix the problem?
> 
> Ciao, Thorsten (wearing his 'the Linux kernel's regression tracker' hat)
> --
> Everything you wanna know about Linux kernel regression tracking:
> https://linux-regtracking.leemhuis.info/about/#tldr
> If I did something stupid, please tell me, as explained on that page.
> 
> #regzbot poke
> 
> On 19.01.23 15:33, Linux kernel regression tracking (Thorsten Leemhuis)
> wrote:
>> [adding various lists and the two other nouveau maintainers to the list
>> of recipients]
> 
>> On 18.01.23 21:59, Chris Clayton wrote:
>>> Hi.
>>>
>>> I build and installed the lastest development kernel earlier this week. I've found that when I try the laptop down (or
>>> reboot it), it hangs right at the end of closing the current session. The last line I see on  the screen when rebooting is:
>>>
>>> 	sd 4:0:0:0: [sda] Synchronising SCSI cache
>>>
>>> when closing down I see one additional line:
>>>
>>> 	sd 4:0:0:0 [sda]Stopping disk
>>>
>>> In both cases the machine then hangs and I have to hold down the power button fot a few seconds to switch it off.
>>>
>>> Linux 6.1 is OK but 6.2-rc1 hangs, so I bisected between this two and landed on:
>>>
>>> 	# first bad commit: [0e44c21708761977dcbea9b846b51a6fb684907a] drm/nouveau/flcn: new code to load+boot simple HS FWs
>>> (VPR scrubber)
>>>
>>> I built and installed a kernel with f15cde64b66161bfa74fb58f4e5697d8265b802e (the parent of the bad commit) checked out
>>> and that shuts down and reboots fine. It the did the same with the bad commit checked out and that does indeed hang, so
>>> I'm confident the bisect outcome is OK.
>>>
>>> Kernels 6.1.6 and 5.15.88 are also OK.
>>>
>>> My system had dual GPUs - one intel and one NVidia. Related extracts from 'lscpi -v' is:
>>>
>>> 00:02.0 VGA compatible controller: Intel Corporation CometLake-H GT2 [UHD Graphics] (rev 05) (prog-if 00 [VGA controller])
>>>         Subsystem: CLEVO/KAPOK Computer CometLake-H GT2 [UHD Graphics]
>>>
>>>         Flags: bus master, fast devsel, latency 0, IRQ 142
>>>
>>>         Memory at c2000000 (64-bit, non-prefetchable) [size=16M]
>>>
>>>         Memory at a0000000 (64-bit, prefetchable) [size=256M]
>>>
>>>         I/O ports at 5000 [size=64]
>>>
>>>         Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
>>>
>>>         Capabilities: [40] Vendor Specific Information: Len=0c <?>
>>>
>>>         Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
>>>
>>>         Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
>>>
>>>         Capabilities: [d0] Power Management version 2
>>>
>>>         Kernel driver in use: i915
>>>
>>>         Kernel modules: i915
>>>
>>>
>>> 01:00.0 VGA compatible controller: NVIDIA Corporation TU117M [GeForce GTX 1650 Ti Mobile] (rev a1) (prog-if 00 [VGA
>>> controller])
>>>         Subsystem: CLEVO/KAPOK Computer TU117M [GeForce GTX 1650 Ti Mobile]
>>>         Flags: bus master, fast devsel, latency 0, IRQ 141
>>>         Memory at c4000000 (32-bit, non-prefetchable) [size=16M]
>>>         Memory at b0000000 (64-bit, prefetchable) [size=256M]
>>>         Memory at c0000000 (64-bit, prefetchable) [size=32M]
>>>         I/O ports at 4000 [size=128]
>>>         Expansion ROM at c3000000 [disabled] [size=512K]
>>>         Capabilities: [60] Power Management version 3
>>>         Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
>>>         Capabilities: [78] Express Legacy Endpoint, MSI 00
>>>         Kernel driver in use: nouveau
>>>         Kernel modules: nouveau
>>>
>>> DRI_PRIME=1 is exported in one of my init scripts (yes, I am still using sysvinit).
>>>
>>> I've attached the bisect.log, but please let me know if I can provide any other diagnostics. Please cc me as I'm not
>>> subscribed.
>>
>> Thanks for the report. To be sure the issue doesn't fall through the
>> cracks unnoticed, I'm adding it to regzbot, the Linux kernel regression
>> tracking bot:
>>
>> #regzbot ^introduced e44c2170876197
>> #regzbot title drm: nouveau: hangs on poweroff/reboot
>> #regzbot ignore-activity
>>
>> This isn't a regression? This issue or a fix for it are already
>> discussed somewhere else? It was fixed already? You want to clarify when
>> the regression started to happen? Or point out I got the title or
>> something else totally wrong? Then just reply and tell me -- ideally
>> while also telling regzbot about it, as explained by the page listed in
>> the footer of this mail.
>>
>> Developers: When fixing the issue, remember to add 'Link:' tags pointing
>> to the report (the parent of this mail). See page linked in footer for
>> details.
>>
>> Ciao, Thorsten (wearing his 'the Linux kernel's regression tracker' hat)
>> --
>> Everything you wanna know about Linux kernel regression tracking:
>> https://linux-regtracking.leemhuis.info/about/#tldr
>> That page also explains what to do if mails like this annoy you.