[v2] media: mediatek: vcodec: fix AV1 decode fail for 36bit iova

[Xiaoyong Lu]

Fix av1 decode fail when iova is 36bit.

Decoder hardware will access incorrect iova address when tile buffer is
36bit, it will lead to iommu fault when hardware access dram data.

Fixes: 2f5d0aef37c6 ("media: mediatek: vcodec: support stateless AV1 decoder")
Signed-off-by: Xiaoyong Lu<xiaoyong.lu at mediatek.com>
---
Changes from v1

- prefer '|' rather than '+'
- prefer '&' rather than shift operation
- add comments for address operations

v1:
- VDEC HW can access tile buffer and decode normally.
- Test ok by mt8195 32bit and mt8188 36bit iova.

---
 .../mediatek/vcodec/vdec/vdec_av1_req_lat_if.c       | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/media/platform/mediatek/vcodec/vdec/vdec_av1_req_lat_if.c b/drivers/media/platform/mediatek/vcodec/vdec/vdec_av1_req_lat_if.c
index 404a1a23fd402..e9f2393f6a883 100644
--- a/drivers/media/platform/mediatek/vcodec/vdec/vdec_av1_req_lat_if.c
+++ b/drivers/media/platform/mediatek/vcodec/vdec/vdec_av1_req_lat_if.c
@@ -1658,9 +1658,9 @@ static void vdec_av1_slice_setup_tile_buffer(struct vdec_av1_slice_instance *ins
 	u32 allow_update_cdf = 0;
 	u32 sb_boundary_x_m1 = 0, sb_boundary_y_m1 = 0;
 	int tile_info_base;
-	u32 tile_buf_pa;
+	u64 tile_buf_pa;
 	u32 *tile_info_buf = instance->tile.va;
-	u32 pa = (u32)bs->dma_addr;
+	u64 pa = (u64)bs->dma_addr;
 
 	if (uh->disable_cdf_update == 0)
 		allow_update_cdf = 1;
@@ -1673,8 +1673,12 @@ static void vdec_av1_slice_setup_tile_buffer(struct vdec_av1_slice_instance *ins
 		tile_info_buf[tile_info_base + 0] = (tile_group->tile_size[tile_num] << 3);
 		tile_buf_pa = pa + tile_group->tile_start_offset[tile_num];
 
-		tile_info_buf[tile_info_base + 1] = (tile_buf_pa >> 4) << 4;
-		tile_info_buf[tile_info_base + 2] = (tile_buf_pa % 16) << 3;
+		/* save av1 tile high 4bits(bit 32-35) address in lower 4 bits position
+		 * and clear original for hw requirement.
+		 */
+		tile_info_buf[tile_info_base + 1] = (tile_buf_pa & 0xFFFFFFF0ull) |
+			((tile_buf_pa & 0xF00000000ull) >> 32);
+		tile_info_buf[tile_info_base + 2] = (tile_buf_pa & 0xFull) << 3;
 
 		sb_boundary_x_m1 =
 			(tile->mi_col_starts[tile_col + 1] - tile->mi_col_starts[tile_col] - 1) &
-- 
2.18.0