[PATCH v14 06/10] drm/msm/dpu: add support for DSC encoder v1.2 engine
Marijn Suijten
marijn.suijten at somainline.org
Sun Jun 4 21:56:41 UTC 2023
On 2023-05-25 10:40:54, Kuogee Hsieh wrote:
> Add support for DSC 1.2 by providing the necessary hooks to program
> the DPU DSC 1.2 encoder.
>
> Changes in v3:
> -- fixed kernel test rebot report that "__iomem *off" is declared but not
> used at dpu_hw_dsc_config_1_2()
> -- unrolling thresh loops
>
> Changes in v4:
> -- delete DPU_DSC_HW_REV_1_1
> -- delete off and used real register name directly
>
> Changes in v7:
> -- replace offset with sblk->enc.base
> -- replace ss with slice
>
> Changes in v8:
> -- fixed checkpatch warning
>
> Changes in v9:
> -- replaced __dsc_calc_ob_max_addr() with __dsc_calc_output_buf_max_addr()
> -- replaced variable num_ss with num_softslice
> -- remove inline from function declaration
>
> changes in v10:
> -- rewording text of changes in v9
> -- replace DPU_DSC_NATIVE_422_EN with DPU_DSC_NATIVE_42x_EN
> -- replace drm_dsc_calculate_flatness_det_thresh() with drm_dsc_flatness_det_thresh()
>
> Signed-off-by: Kuogee Hsieh <quic_khsieh at quicinc.com>
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
Since I have given this code adequate comments, and have finally
successfully used/tested it on SM8350 (Sony Xperia 5III):
Reviewed-by: Marijn Suijten <marijn.suijten at somainline.org>
Note that I did not explicitly check if the register writes match
downstream or reference material.
> ---
> drivers/gpu/drm/msm/Makefile | 1 +
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 31 +-
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h | 14 +-
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc_1_2.c | 387 +++++++++++++++++++++++++
> drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c | 7 +-
> 5 files changed, 436 insertions(+), 4 deletions(-)
> create mode 100644 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc_1_2.c
>
> diff --git a/drivers/gpu/drm/msm/Makefile b/drivers/gpu/drm/msm/Makefile
> index 7274c412..4c7195af2 100644
> --- a/drivers/gpu/drm/msm/Makefile
> +++ b/drivers/gpu/drm/msm/Makefile
> @@ -65,6 +65,7 @@ msm-$(CONFIG_DRM_MSM_DPU) += \
> disp/dpu1/dpu_hw_catalog.o \
> disp/dpu1/dpu_hw_ctl.o \
> disp/dpu1/dpu_hw_dsc.o \
> + disp/dpu1/dpu_hw_dsc_1_2.o \
> disp/dpu1/dpu_hw_interrupts.o \
> disp/dpu1/dpu_hw_intf.o \
> disp/dpu1/dpu_hw_lm.o \
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> index 83854e8..11610f7 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> @@ -1,6 +1,6 @@
> /* SPDX-License-Identifier: GPL-2.0-only */
> /*
> - * Copyright (c) 2022. Qualcomm Innovation Center, Inc. All rights reserved.
> + * Copyright (c) 2022-2023, Qualcomm Innovation Center, Inc. All rights reserved.
> * Copyright (c) 2015-2018, 2020 The Linux Foundation. All rights reserved.
> */
>
> @@ -244,12 +244,18 @@ enum {
> };
>
> /**
> - * DSC features
> + * DSC sub-blocks/features
> * @DPU_DSC_OUTPUT_CTRL Configure which PINGPONG block gets
> * the pixel output from this DSC.
> + * @DPU_DSC_HW_REV_1_2 DSC block supports DSC 1.1 and 1.2
> + * @DPU_DSC_NATIVE_42x_EN Supports NATIVE_422_EN and NATIVE_420_EN encoding
> + * @DPU_DSC_MAX
> */
> enum {
> DPU_DSC_OUTPUT_CTRL = 0x1,
> + DPU_DSC_HW_REV_1_2,
> + DPU_DSC_NATIVE_42x_EN,
> + DPU_DSC_MAX
> };
>
> /**
> @@ -306,6 +312,14 @@ struct dpu_pp_blk {
> };
>
> /**
> + * struct dpu_dsc_blk - DSC Encoder sub-blk information
> + * @info: HW register and features supported by this sub-blk
> + */
> +struct dpu_dsc_blk {
> + DPU_HW_SUBBLK_INFO;
> +};
> +
> +/**
> * enum dpu_qos_lut_usage - define QoS LUT use cases
> */
> enum dpu_qos_lut_usage {
> @@ -452,6 +466,16 @@ struct dpu_pingpong_sub_blks {
> };
>
> /**
> + * struct dpu_dsc_sub_blks - DSC sub-blks
> + * @enc: DSC encoder sub-block
> + * @ctl: DSC controller sub-block
> + */
> +struct dpu_dsc_sub_blks {
> + struct dpu_dsc_blk enc;
> + struct dpu_dsc_blk ctl;
> +};
> +
> +/**
> * dpu_clk_ctrl_type - Defines top level clock control signals
> */
> enum dpu_clk_ctrl_type {
> @@ -605,10 +629,13 @@ struct dpu_merge_3d_cfg {
> * struct dpu_dsc_cfg - information of DSC blocks
> * @id enum identifying this block
> * @base register offset of this block
> + * @len: length of hardware block
> * @features bit mask identifying sub-blocks/features
> + * @sblk: sub-blocks information
> */
> struct dpu_dsc_cfg {
> DPU_HW_BLK_INFO;
> + const struct dpu_dsc_sub_blks *sblk;
> };
>
> /**
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h
> index 138080a..d5b597a 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h
> @@ -1,5 +1,8 @@
> /* SPDX-License-Identifier: GPL-2.0-only */
> -/* Copyright (c) 2020-2022, Linaro Limited */
> +/*
> + * Copyright (c) 2020-2022, Linaro Limited
> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved
> + */
>
> #ifndef _DPU_HW_DSC_H
> #define _DPU_HW_DSC_H
> @@ -69,6 +72,15 @@ struct dpu_hw_dsc *dpu_hw_dsc_init(const struct dpu_dsc_cfg *cfg,
> void __iomem *addr);
>
> /**
> + * dpu_hw_dsc_init_1_2() - initializes the v1.2 DSC hw driver object
> + * @cfg: DSC catalog entry for which driver object is required
> + * @addr: Mapped register io address of MDP
> + * Returns: Error code or allocated dpu_hw_dsc context
> + */
> +struct dpu_hw_dsc *dpu_hw_dsc_init_1_2(const struct dpu_dsc_cfg *cfg,
> + void __iomem *addr);
> +
> +/**
> * dpu_hw_dsc_destroy - destroys dsc driver context
> * @dsc: Pointer to dsc driver context returned by dpu_hw_dsc_init
> */
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc_1_2.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc_1_2.c
> new file mode 100644
> index 00000000..24fe1d9
> --- /dev/null
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc_1_2.c
> @@ -0,0 +1,387 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved
> + */
> +
> +#include <drm/display/drm_dsc_helper.h>
> +
> +#include "dpu_kms.h"
> +#include "dpu_hw_catalog.h"
> +#include "dpu_hwio.h"
> +#include "dpu_hw_mdss.h"
> +#include "dpu_hw_dsc.h"
> +
> +#define DSC_CMN_MAIN_CNF 0x00
> +
> +/* DPU_DSC_ENC register offsets */
> +#define ENC_DF_CTRL 0x00
> +#define ENC_GENERAL_STATUS 0x04
> +#define ENC_HSLICE_STATUS 0x08
> +#define ENC_OUT_STATUS 0x0C
> +#define ENC_INT_STAT 0x10
> +#define ENC_INT_CLR 0x14
> +#define ENC_INT_MASK 0x18
> +#define DSC_MAIN_CONF 0x30
> +#define DSC_PICTURE_SIZE 0x34
> +#define DSC_SLICE_SIZE 0x38
> +#define DSC_MISC_SIZE 0x3C
> +#define DSC_HRD_DELAYS 0x40
> +#define DSC_RC_SCALE 0x44
> +#define DSC_RC_SCALE_INC_DEC 0x48
> +#define DSC_RC_OFFSETS_1 0x4C
> +#define DSC_RC_OFFSETS_2 0x50
> +#define DSC_RC_OFFSETS_3 0x54
> +#define DSC_RC_OFFSETS_4 0x58
> +#define DSC_FLATNESS_QP 0x5C
> +#define DSC_RC_MODEL_SIZE 0x60
> +#define DSC_RC_CONFIG 0x64
> +#define DSC_RC_BUF_THRESH_0 0x68
> +#define DSC_RC_BUF_THRESH_1 0x6C
> +#define DSC_RC_BUF_THRESH_2 0x70
> +#define DSC_RC_BUF_THRESH_3 0x74
> +#define DSC_RC_MIN_QP_0 0x78
> +#define DSC_RC_MIN_QP_1 0x7C
> +#define DSC_RC_MIN_QP_2 0x80
> +#define DSC_RC_MAX_QP_0 0x84
> +#define DSC_RC_MAX_QP_1 0x88
> +#define DSC_RC_MAX_QP_2 0x8C
> +#define DSC_RC_RANGE_BPG_OFFSETS_0 0x90
> +#define DSC_RC_RANGE_BPG_OFFSETS_1 0x94
> +#define DSC_RC_RANGE_BPG_OFFSETS_2 0x98
> +
> +/* DPU_DSC_CTL register offsets */
> +#define DSC_CTL 0x00
> +#define DSC_CFG 0x04
> +#define DSC_DATA_IN_SWAP 0x08
> +#define DSC_CLK_CTRL 0x0C
> +
> +static int _dsc_calc_output_buf_max_addr(struct dpu_hw_dsc *hw_dsc, int num_softslice)
> +{
> + int max_addr = 2400 / num_softslice;
> +
> + if (hw_dsc->caps->features & BIT(DPU_DSC_NATIVE_42x_EN))
> + max_addr /= 2;
> +
> + return max_addr - 1;
> +};
> +
> +static void dpu_hw_dsc_disable_1_2(struct dpu_hw_dsc *hw_dsc)
> +{
> + struct dpu_hw_blk_reg_map *hw;
> + const struct dpu_dsc_sub_blks *sblk;
> +
> + if (!hw_dsc)
> + return;
> +
> + hw = &hw_dsc->hw;
> + sblk = hw_dsc->caps->sblk;
> + DPU_REG_WRITE(hw, sblk->ctl.base + DSC_CFG, 0);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + ENC_DF_CTRL, 0);
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_MAIN_CONF, 0);
> +}
> +
> +static void dpu_hw_dsc_config_1_2(struct dpu_hw_dsc *hw_dsc,
> + struct drm_dsc_config *dsc,
> + u32 mode,
> + u32 initial_lines)
> +{
> + struct dpu_hw_blk_reg_map *hw;
> + const struct dpu_dsc_sub_blks *sblk;
> + u32 data = 0;
> + u32 det_thresh_flatness;
> + u32 num_active_slice_per_enc;
> + u32 bpp;
> +
> + if (!hw_dsc || !dsc)
> + return;
> +
> + hw = &hw_dsc->hw;
> +
> + sblk = hw_dsc->caps->sblk;
> +
> + if (mode & DSC_MODE_SPLIT_PANEL)
> + data |= BIT(0);
> +
> + if (mode & DSC_MODE_MULTIPLEX)
> + data |= BIT(1);
> +
> + num_active_slice_per_enc = dsc->slice_count;
> + if (mode & DSC_MODE_MULTIPLEX)
> + num_active_slice_per_enc = dsc->slice_count / 2;
> +
> + data |= (num_active_slice_per_enc & 0x3) << 7;
> +
> + DPU_REG_WRITE(hw, DSC_CMN_MAIN_CNF, data);
> +
> + data = (initial_lines & 0xff);
Are these parenthesis needed?
> +
> + if (mode & DSC_MODE_VIDEO)
> + data |= BIT(9);
> +
> + data |= (_dsc_calc_output_buf_max_addr(hw_dsc, num_active_slice_per_enc) << 18);
parenthesis?
- Marijn
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + ENC_DF_CTRL, data);
> +
> + data = (dsc->dsc_version_minor & 0xf) << 28;
> + if (dsc->dsc_version_minor == 0x2) {
> + if (dsc->native_422)
> + data |= BIT(22);
> + if (dsc->native_420)
> + data |= BIT(21);
> + }
> +
> + bpp = dsc->bits_per_pixel;
> + /* as per hw requirement bpp should be programmed
> + * twice the actual value in case of 420 or 422 encoding
> + */
> + if (dsc->native_422 || dsc->native_420)
> + bpp = 2 * bpp;
> +
> + data |= bpp << 10;
> +
> + if (dsc->block_pred_enable)
> + data |= BIT(20);
> +
> + if (dsc->convert_rgb)
> + data |= BIT(4);
> +
> + data |= (dsc->line_buf_depth & 0xf) << 6;
> + data |= dsc->bits_per_component & 0xf;
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_MAIN_CONF, data);
> +
> + data = (dsc->pic_width & 0xffff) |
> + ((dsc->pic_height & 0xffff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_PICTURE_SIZE, data);
> +
> + data = (dsc->slice_width & 0xffff) |
> + ((dsc->slice_height & 0xffff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_SLICE_SIZE, data);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_MISC_SIZE,
> + (dsc->slice_chunk_size) & 0xffff);
> +
> + data = (dsc->initial_xmit_delay & 0xffff) |
> + ((dsc->initial_dec_delay & 0xffff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_HRD_DELAYS, data);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_SCALE,
> + dsc->initial_scale_value & 0x3f);
> +
> + data = (dsc->scale_increment_interval & 0xffff) |
> + ((dsc->scale_decrement_interval & 0x7ff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_SCALE_INC_DEC, data);
> +
> + data = (dsc->first_line_bpg_offset & 0x1f) |
> + ((dsc->second_line_bpg_offset & 0x1f) << 5);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_OFFSETS_1, data);
> +
> + data = (dsc->nfl_bpg_offset & 0xffff) |
> + ((dsc->slice_bpg_offset & 0xffff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_OFFSETS_2, data);
> +
> + data = (dsc->initial_offset & 0xffff) |
> + ((dsc->final_offset & 0xffff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_OFFSETS_3, data);
> +
> + data = (dsc->nsl_bpg_offset & 0xffff) |
> + ((dsc->second_line_offset_adj & 0xffff) << 16);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_OFFSETS_4, data);
> +
> + det_thresh_flatness = drm_dsc_flatness_det_thresh(dsc);
> + data = (dsc->flatness_min_qp & 0x1f) |
> + ((dsc->flatness_max_qp & 0x1f) << 5) |
> + ((det_thresh_flatness & 0xff) << 10);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_FLATNESS_QP, data);
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MODEL_SIZE,
> + (dsc->rc_model_size) & 0xffff);
> +
> + data = dsc->rc_edge_factor & 0xf;
> + data |= (dsc->rc_quant_incr_limit0 & 0x1f) << 8;
> + data |= (dsc->rc_quant_incr_limit1 & 0x1f) << 13;
> + data |= (dsc->rc_tgt_offset_high & 0xf) << 20;
> + data |= (dsc->rc_tgt_offset_low & 0xf) << 24;
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_CONFIG, data);
> +
> + /* program the dsc wrapper */
> + data = BIT(0); /* encoder enable */
> + if (dsc->native_422)
> + data |= BIT(8);
> + else if (dsc->native_420)
> + data |= BIT(9);
> + if (!dsc->convert_rgb)
> + data |= BIT(10);
> + if (dsc->bits_per_component == 8)
> + data |= BIT(11);
> + if (mode & DSC_MODE_SPLIT_PANEL)
> + data |= BIT(12);
> + if (mode & DSC_MODE_MULTIPLEX)
> + data |= BIT(13);
> + if (!(mode & DSC_MODE_VIDEO))
> + data |= BIT(17);
> +
> + DPU_REG_WRITE(hw, sblk->ctl.base + DSC_CFG, data);
> +}
> +
> +static void dpu_hw_dsc_config_thresh_1_2(struct dpu_hw_dsc *hw_dsc,
> + struct drm_dsc_config *dsc)
> +{
> + struct dpu_hw_blk_reg_map *hw;
> + const struct dpu_dsc_sub_blks *sblk;
> + struct drm_dsc_rc_range_parameters *rc;
> +
> + if (!hw_dsc || !dsc)
> + return;
> +
> + hw = &hw_dsc->hw;
> +
> + sblk = hw_dsc->caps->sblk;
> +
> + rc = dsc->rc_range_params;
> +
> + /*
> + * With BUF_THRESH -- 14 in total
> + * each register contains 4 thresh values with the last register
> + * containing only 2 thresh values
> + */
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_BUF_THRESH_0,
> + (dsc->rc_buf_thresh[0] << 0) |
> + (dsc->rc_buf_thresh[1] << 8) |
> + (dsc->rc_buf_thresh[2] << 16) |
> + (dsc->rc_buf_thresh[3] << 24));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_BUF_THRESH_1,
> + (dsc->rc_buf_thresh[4] << 0) |
> + (dsc->rc_buf_thresh[5] << 8) |
> + (dsc->rc_buf_thresh[6] << 16) |
> + (dsc->rc_buf_thresh[7] << 24));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_BUF_THRESH_2,
> + (dsc->rc_buf_thresh[8] << 0) |
> + (dsc->rc_buf_thresh[9] << 8) |
> + (dsc->rc_buf_thresh[10] << 16) |
> + (dsc->rc_buf_thresh[11] << 24));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_BUF_THRESH_3,
> + (dsc->rc_buf_thresh[12] << 0) |
> + (dsc->rc_buf_thresh[13] << 8));
> +
> + /*
> + * with min/max_QP -- 5 bits
> + * each register contains 5 min_qp or max_qp for total of 15
> + *
> + * With BPG_OFFSET -- 6 bits
> + * each register contains 5 BPG_offset for total of 15
> + */
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MIN_QP_0,
> + (rc[0].range_min_qp << 0) |
> + (rc[1].range_min_qp << 5) |
> + (rc[2].range_min_qp << 10) |
> + (rc[3].range_min_qp << 15) |
> + (rc[4].range_min_qp << 20));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MAX_QP_0,
> + (rc[0].range_max_qp << 0) |
> + (rc[1].range_max_qp << 5) |
> + (rc[2].range_max_qp << 10) |
> + (rc[3].range_max_qp << 15) |
> + (rc[4].range_max_qp << 20));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_RANGE_BPG_OFFSETS_0,
> + (rc[0].range_bpg_offset << 0) |
> + (rc[1].range_bpg_offset << 6) |
> + (rc[2].range_bpg_offset << 12) |
> + (rc[3].range_bpg_offset << 18) |
> + (rc[4].range_bpg_offset << 24));
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MIN_QP_1,
> + (rc[5].range_min_qp << 0) |
> + (rc[6].range_min_qp << 5) |
> + (rc[7].range_min_qp << 10) |
> + (rc[8].range_min_qp << 15) |
> + (rc[9].range_min_qp << 20));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MAX_QP_1,
> + (rc[5].range_max_qp << 0) |
> + (rc[6].range_max_qp << 5) |
> + (rc[7].range_max_qp << 10) |
> + (rc[8].range_max_qp << 15) |
> + (rc[9].range_max_qp << 20));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_RANGE_BPG_OFFSETS_1,
> + (rc[5].range_bpg_offset << 0) |
> + (rc[6].range_bpg_offset << 6) |
> + (rc[7].range_bpg_offset << 12) |
> + (rc[8].range_bpg_offset << 18) |
> + (rc[9].range_bpg_offset << 24));
> +
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MIN_QP_2,
> + (rc[10].range_min_qp << 0) |
> + (rc[11].range_min_qp << 5) |
> + (rc[12].range_min_qp << 10) |
> + (rc[13].range_min_qp << 15) |
> + (rc[14].range_min_qp << 20));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_MAX_QP_2,
> + (rc[10].range_max_qp << 0) |
> + (rc[11].range_max_qp << 5) |
> + (rc[12].range_max_qp << 10) |
> + (rc[13].range_max_qp << 15) |
> + (rc[14].range_max_qp << 20));
> + DPU_REG_WRITE(hw, sblk->enc.base + DSC_RC_RANGE_BPG_OFFSETS_2,
> + (rc[10].range_bpg_offset << 0) |
> + (rc[11].range_bpg_offset << 6) |
> + (rc[12].range_bpg_offset << 12) |
> + (rc[13].range_bpg_offset << 18) |
> + (rc[14].range_bpg_offset << 24));
> +}
> +
> +static void dpu_hw_dsc_bind_pingpong_blk_1_2(struct dpu_hw_dsc *hw_dsc,
> + const enum dpu_pingpong pp)
> +{
> + struct dpu_hw_blk_reg_map *hw;
> + const struct dpu_dsc_sub_blks *sblk;
> + int mux_cfg = 0xf; /* Disabled */
> +
> + hw = &hw_dsc->hw;
> +
> + sblk = hw_dsc->caps->sblk;
> +
> + if (pp)
> + mux_cfg = (pp - PINGPONG_0) & 0x7;
> +
> + DPU_REG_WRITE(hw, sblk->ctl.base + DSC_CTL, mux_cfg);
> +}
> +
> +static void _setup_dcs_ops_1_2(struct dpu_hw_dsc_ops *ops,
> + const unsigned long features)
> +{
> + ops->dsc_disable = dpu_hw_dsc_disable_1_2;
> + ops->dsc_config = dpu_hw_dsc_config_1_2;
> + ops->dsc_config_thresh = dpu_hw_dsc_config_thresh_1_2;
> + ops->dsc_bind_pingpong_blk = dpu_hw_dsc_bind_pingpong_blk_1_2;
> +}
> +
> +struct dpu_hw_dsc *dpu_hw_dsc_init_1_2(const struct dpu_dsc_cfg *cfg,
> + void __iomem *addr)
> +{
> + struct dpu_hw_dsc *c;
> +
> + c = kzalloc(sizeof(*c), GFP_KERNEL);
> + if (!c)
> + return ERR_PTR(-ENOMEM);
> +
> + c->hw.blk_addr = addr + cfg->base;
> + c->hw.log_mask = DPU_DBG_MASK_DSC;
> +
> + c->idx = cfg->id;
> + c->caps = cfg;
> + _setup_dcs_ops_1_2(&c->ops, c->caps->features);
> +
> + return c;
> +}
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c
> index f0fc704..502dd60 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c
> @@ -1,6 +1,7 @@
> // SPDX-License-Identifier: GPL-2.0-only
> /*
> * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> #define pr_fmt(fmt) "[drm:%s] " fmt, __func__
> @@ -246,7 +247,11 @@ int dpu_rm_init(struct dpu_rm *rm,
> struct dpu_hw_dsc *hw;
> const struct dpu_dsc_cfg *dsc = &cat->dsc[i];
>
> - hw = dpu_hw_dsc_init(dsc, mmio);
> + if (test_bit(DPU_DSC_HW_REV_1_2, &dsc->features))
> + hw = dpu_hw_dsc_init_1_2(dsc, mmio);
> + else
> + hw = dpu_hw_dsc_init(dsc, mmio);
> +
> if (IS_ERR_OR_NULL(hw)) {
> rc = PTR_ERR(hw);
> DPU_ERROR("failed dsc object creation: err %d\n", rc);
> --
> 2.7.4
>
More information about the dri-devel
mailing list