[Freedreno] [PATCH v3 6/7] drm/msm/dsi: Add phy configuration for MSM8226
Jeykumar Sankaran
quic_jeykumar at quicinc.com
Wed Jun 7 19:46:31 UTC 2023
On 6/1/2023 10:00 AM, Luca Weiss wrote:
> MSM8226 uses a modified PLL lock sequence compared to MSM8974, which is
> based on the function dsi_pll_enable_seq_m in the msm-3.10 kernel.
>
> Worth noting that the msm-3.10 downstream kernel also will try other
> sequences in case this one doesn't work, but during testing it has shown
> that the _m sequence succeeds first time also:
>
> .pll_enable_seqs[0] = dsi_pll_enable_seq_m,
> .pll_enable_seqs[1] = dsi_pll_enable_seq_m,
> .pll_enable_seqs[2] = dsi_pll_enable_seq_d,
> .pll_enable_seqs[3] = dsi_pll_enable_seq_d,
> .pll_enable_seqs[4] = dsi_pll_enable_seq_f1,
> .pll_enable_seqs[5] = dsi_pll_enable_seq_c,
> .pll_enable_seqs[6] = dsi_pll_enable_seq_e,
>
> We may need to expand this in the future.
>
> Signed-off-by: Luca Weiss <luca at z3ntu.xyz>
> ---
> drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 2 +
> drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 3 +-
> drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c | 97 ++++++++++++++++++++++++++++++
> 3 files changed, 101 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> index bb09cbe8ff86..9d5795c58a98 100644
> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> @@ -541,6 +541,8 @@ static const struct of_device_id dsi_phy_dt_match[] = {
> .data = &dsi_phy_28nm_hpm_famb_cfgs },
> { .compatible = "qcom,dsi-phy-28nm-lp",
> .data = &dsi_phy_28nm_lp_cfgs },
> + { .compatible = "qcom,dsi-phy-28nm-8226",
> + .data = &dsi_phy_28nm_8226_cfgs },
> #endif
> #ifdef CONFIG_DRM_MSM_DSI_20NM_PHY
> { .compatible = "qcom,dsi-phy-20nm",
> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
> index 7137a17ae523..8b640d174785 100644
> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
> @@ -46,8 +46,9 @@ struct msm_dsi_phy_cfg {
> extern const struct msm_dsi_phy_cfg dsi_phy_28nm_hpm_cfgs;
> extern const struct msm_dsi_phy_cfg dsi_phy_28nm_hpm_famb_cfgs;
> extern const struct msm_dsi_phy_cfg dsi_phy_28nm_lp_cfgs;
> -extern const struct msm_dsi_phy_cfg dsi_phy_20nm_cfgs;
> +extern const struct msm_dsi_phy_cfg dsi_phy_28nm_8226_cfgs;
> extern const struct msm_dsi_phy_cfg dsi_phy_28nm_8960_cfgs;
> +extern const struct msm_dsi_phy_cfg dsi_phy_20nm_cfgs;
> extern const struct msm_dsi_phy_cfg dsi_phy_14nm_cfgs;
> extern const struct msm_dsi_phy_cfg dsi_phy_14nm_660_cfgs;
> extern const struct msm_dsi_phy_cfg dsi_phy_14nm_2290_cfgs;
> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c
> index 4c1bf55c5f38..ceec7bb87bf1 100644
> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c
> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c
> @@ -37,6 +37,7 @@
>
> /* v2.0.0 28nm LP implementation */
> #define DSI_PHY_28NM_QUIRK_PHY_LP BIT(0)
> +#define DSI_PHY_28NM_QUIRK_PHY_8226 BIT(1)
>
> #define LPFR_LUT_SIZE 10
> struct lpfr_cfg {
> @@ -377,6 +378,74 @@ static int dsi_pll_28nm_vco_prepare_hpm(struct clk_hw *hw)
> return ret;
> }
>
> +static int dsi_pll_28nm_vco_prepare_8226(struct clk_hw *hw)
> +{
> + struct dsi_pll_28nm *pll_28nm = to_pll_28nm(hw);
> + struct device *dev = &pll_28nm->phy->pdev->dev;
> + void __iomem *base = pll_28nm->phy->pll_base;
> + u32 max_reads = 5, timeout_us = 100;
> + bool locked;
> + u32 val;
> + int i;
> +
> + DBG("id=%d", pll_28nm->phy->id);
> +
> + pll_28nm_software_reset(pll_28nm);
> +
> + /*
> + * PLL power up sequence.
> + * Add necessary delays recommended by hardware.
> + */
> + dsi_phy_write(base + REG_DSI_28nm_PHY_PLL_CAL_CFG1, 0x34);
> +
> + val = DSI_28nm_PHY_PLL_GLB_CFG_PLL_PWRDN_B;
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_GLB_CFG, val, 200);
> +
> + val |= DSI_28nm_PHY_PLL_GLB_CFG_PLL_PWRGEN_PWRDN_B;
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_GLB_CFG, val, 200);
> +
> + val |= DSI_28nm_PHY_PLL_GLB_CFG_PLL_LDO_PWRDN_B;
> + val |= DSI_28nm_PHY_PLL_GLB_CFG_PLL_ENABLE;
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_GLB_CFG, val, 600);
> +
> + for (i = 0; i < 7; i++) {
> + /* DSI Uniphy lock detect setting */
> + dsi_phy_write(base + REG_DSI_28nm_PHY_PLL_LKDET_CFG2, 0x0d);
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_LKDET_CFG2,
> + 0x0c, 100);
> + dsi_phy_write(base + REG_DSI_28nm_PHY_PLL_LKDET_CFG2, 0x0d);
> +
> + /* poll for PLL ready status */
> + locked = pll_28nm_poll_for_ready(pll_28nm,
> + max_reads, timeout_us);
> + if (locked)
> + break;
> +
> + pll_28nm_software_reset(pll_28nm);
> +
> + /*
> + * PLL power up sequence.
> + * Add necessary delays recommended by hardware.
> + */
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_PWRGEN_CFG, 0x00, 50);
> +
> + val = DSI_28nm_PHY_PLL_GLB_CFG_PLL_PWRDN_B;
> + val |= DSI_28nm_PHY_PLL_GLB_CFG_PLL_PWRGEN_PWRDN_B;
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_GLB_CFG, val, 100);
> +
> + val |= DSI_28nm_PHY_PLL_GLB_CFG_PLL_LDO_PWRDN_B;
> + val |= DSI_28nm_PHY_PLL_GLB_CFG_PLL_ENABLE;
> + dsi_phy_write_udelay(base + REG_DSI_28nm_PHY_PLL_GLB_CFG, val, 600);
> + }
> +
> + if (unlikely(!locked))
> + DRM_DEV_ERROR(dev, "DSI PLL lock failed\n");
> + else
> + DBG("DSI PLL Lock success");
> +
> + return locked ? 0 : -EINVAL;
> +}
> +
Could you please share the downstream reference you used to come up with
this sequence?
Thanks and Regards,
Jeykumar S.
> static int dsi_pll_28nm_vco_prepare_lp(struct clk_hw *hw)
> {
> struct dsi_pll_28nm *pll_28nm = to_pll_28nm(hw);
> @@ -471,6 +540,15 @@ static const struct clk_ops clk_ops_dsi_pll_28nm_vco_lp = {
> .is_enabled = dsi_pll_28nm_clk_is_enabled,
> };
>
> +static const struct clk_ops clk_ops_dsi_pll_28nm_vco_8226 = {
> + .round_rate = dsi_pll_28nm_clk_round_rate,
> + .set_rate = dsi_pll_28nm_clk_set_rate,
> + .recalc_rate = dsi_pll_28nm_clk_recalc_rate,
> + .prepare = dsi_pll_28nm_vco_prepare_8226,
> + .unprepare = dsi_pll_28nm_vco_unprepare,
> + .is_enabled = dsi_pll_28nm_clk_is_enabled,
> +};
> +
> /*
> * PLL Callbacks
> */
> @@ -536,6 +614,8 @@ static int pll_28nm_register(struct dsi_pll_28nm *pll_28nm, struct clk_hw **prov
>
> if (pll_28nm->phy->cfg->quirks & DSI_PHY_28NM_QUIRK_PHY_LP)
> vco_init.ops = &clk_ops_dsi_pll_28nm_vco_lp;
> + else if (pll_28nm->phy->cfg->quirks & DSI_PHY_28NM_QUIRK_PHY_8226)
> + vco_init.ops = &clk_ops_dsi_pll_28nm_vco_8226;
> else
> vco_init.ops = &clk_ops_dsi_pll_28nm_vco_hpm;
>
> @@ -820,3 +900,20 @@ const struct msm_dsi_phy_cfg dsi_phy_28nm_lp_cfgs = {
> .quirks = DSI_PHY_28NM_QUIRK_PHY_LP,
> };
>
> +const struct msm_dsi_phy_cfg dsi_phy_28nm_8226_cfgs = {
> + .has_phy_regulator = true,
> + .regulator_data = dsi_phy_28nm_regulators,
> + .num_regulators = ARRAY_SIZE(dsi_phy_28nm_regulators),
> + .ops = {
> + .enable = dsi_28nm_phy_enable,
> + .disable = dsi_28nm_phy_disable,
> + .pll_init = dsi_pll_28nm_init,
> + .save_pll_state = dsi_28nm_pll_save_state,
> + .restore_pll_state = dsi_28nm_pll_restore_state,
> + },
> + .min_pll_rate = VCO_MIN_RATE,
> + .max_pll_rate = VCO_MAX_RATE,
> + .io_start = { 0xfd922b00 },
> + .num_dsi_phy = 1,
> + .quirks = DSI_PHY_28NM_QUIRK_PHY_8226,
> +};
>
More information about the dri-devel
mailing list