[PATCH v2 0/7] Allow dynamic allocation of software IO TLB bounce buffers

[Greg Kroah-Hartman]

On Tue, May 09, 2023 at 09:16:35AM +0200, Petr Tesařík wrote:
> On Wed, 26 Apr 2023 14:44:39 +0200
> Petr Tesařík <petr at tesarici.cz> wrote:
> 
> > Hi Greg,
> > 
> > On Wed, 26 Apr 2023 14:26:36 +0200
> > Greg Kroah-Hartman <gregkh at linuxfoundation.org> wrote:
> > 
> > > On Wed, Apr 26, 2023 at 02:15:20PM +0200, Petr Tesařík wrote:  
> > > > Hi,
> > > > 
> > > > On Wed, 19 Apr 2023 12:03:52 +0200
> > > > Petr Tesarik <petrtesarik at huaweicloud.com> wrote:
> > > >     
> > > > > From: Petr Tesarik <petr.tesarik.ext at huawei.com>
> > > > > 
> > > > > The goal of my work is to provide more flexibility in the sizing of
> > > > > SWIOTLB.
> > > > > 
> > > > > The software IO TLB was designed with these assumptions:
> > > > > 
> > > > > 1. It would not be used much, especially on 64-bit systems.
> > > > > 2. A small fixed memory area (64 MiB by default) is sufficient to
> > > > >    handle the few cases which require a bounce buffer.
> > > > > 3. 64 MiB is little enough that it has no impact on the rest of the
> > > > >    system.
> > > > > 
> > > > > First, if SEV is active, all DMA must be done through shared
> > > > > unencrypted pages, and SWIOTLB is used to make this happen without
> > > > > changing device drivers. The software IO TLB size is increased to
> > > > > 6% of total memory in sev_setup_arch(), but that is more of an
> > > > > approximation. The actual requirements may vary depending on the
> > > > > amount of I/O and which drivers are used. These factors may not be
> > > > > know at boot time, i.e. when SWIOTLB is allocated.
> > > > > 
> > > > > Second, other colleagues have noticed that they can reliably get
> > > > > rid of occasional OOM kills on an Arm embedded device by reducing
> > > > > the SWIOTLB size. This can be achieved with a kernel parameter, but
> > > > > determining the right value puts additional burden on pre-release
> > > > > testing, which could be avoided if SWIOTLB is allocated small and
> > > > > grows only when necessary.    
> > > > 
> > > > Now that merging into 6.4 has begun, what about this patch series? I'm
> > > > eager to get some feedback (positive or negative) and respin the next
> > > > version.    
> > > 
> > > It's the merge window, we can't add new things that haven't been in
> > > linux-next already.  
> > 
> > This is understood. I'm not asking for immediate inclusion.
> > 
> > >   Please resubmit it after -rc1 is out.  
> > 
> > If you can believe that rebasing to -rc1 will be enough, then I will
> > also try to believe I'm lucky. ;-)
> > 
> > The kind of feedback I really want to get is e.g. about the extra
> > per-device DMA-specific fields. If they cannot be added to struct
> > device, then I'd rather start discussing an interim solution, because
> > getting all existing DMA fields out of that struct will take a lot of
> > time...
> 
> All right, 6.4-rc1 is out now. The patch series still applies cleanly.
> 
> Any comments what must be changed (if anything) to get it in?

Try resending it, it's long out of my review queue...

thanks,

greg k-h