[PATCH v1 1/2] drm/msm/dp: enable HDP plugin/unplugged interrupts to hpd_enable/disable

[Bjorn Andersson]

On Wed, May 10, 2023 at 05:39:07PM -0700, Abhinav Kumar wrote:
> 
> 
> On 5/10/2023 4:55 PM, Stephen Boyd wrote:
> > Quoting Kuogee Hsieh (2023-05-10 13:31:04)
> > > The internal_hpd flag was introduced to handle external DP HPD derived from GPIO
> > > pinmuxed into DP controller.
> > 
> > Was it? It looks more like it was done to differentiate between eDP and
> > DP, because internal_hpd is set only if DRM_BRIDGE_OP_HPD is set on the
> > bridge and we only set the bridge op if the connector type is DP. The
> > assumption looks like if you have DP connector_type, you have the gpio
> > pinmuxed for "dp_hot" mode, which isn't exactly true. We don't treat
> > that gpio as an irq either, because it isn't. Instead the gpio is muxed
> > to the mdss inside the SoC and then that generates an mdss interrupt
> > that's combined with non-HPD things like "video ready".
> > 
> > If that all follows, then I don't quite understand why we're setting
> > internal_hpd to false at all at runtime. It should be set to true at
> > some point, but ideally that point is during probe.
> > 
> 
> Kuogee had the same thought originally but were not entirely sure of this
> part of the commit message in Bjorn's original commit which introduced these
> changes.
> 
> "This difference is not appropriately represented by the "is_edp"
> boolean, but is properly represented by the frameworks invocation of the
> hpd_enable() and hpd_disable() callbacks. Switch the current condition
> to rely on these callbacks instead"
> 
> Does this along with below documentation mean we should generate the hpd
> interrupts only after hpd_enable callback happens?
> 
> " * Call &drm_bridge_funcs.hpd_enable if implemented and register the given
> @cb
>  * and @data as hot plug notification callback. From now on the @cb will be
>  * called with @data when an output status change is detected by the bridge,
>  * until hot plug notification gets disabled with drm_bridge_hpd_disable().
> "
> 
> Bjorn, can you please clarify this?
> 

We currently have 3 cases:

1) DP with GPIO: No downstream drm_bridge are connected, is_edp = false
and internal HPD-logic is in used (internal_hpd = true). Power needs to
be on at all times etc.

2) DP without GPIO: Downstream drm_bridge connected, is_edp = false and
internal HPD-logic should not be used/enabled (internal_hpd = false).
Power doesn't need to be on unless hpd_notify is invoked to tell us that
there's something connected...

3) eDP with or without HPD signal and/or HPD gpio. Downstream
drm_bridge/panel is connected, is_edp = true and internal HPD logic is
short-circuited regardless of the panel providing HPD signal or not.


In #1 dp_bridge_hpd_enable() will be invoked to indicate that the DP
controller is expected to perform HPD handling. In #2
dp_bridge_hpd_enable() will _not_ be invoked, instead some downstream
drm_bridge/panel will get the hpd_enable() callback and will be
responsible to updating the HPD state of the chain, which will cause
hpd_notify to be invoked.


Note that #3 is based entirely on the controller, it has currently no
relation to what is attached. It seems reasonable that this is just
another case of #2 (perhaps just always reporting
connector_status_connected?).

Regards,
Bjorn

> > > HPD plug/unplug interrupts cannot be enabled until
> > > internal_hpd flag is set to true.
> > > At both bootup and resume time, the DP driver will enable external DP
> > > plugin interrupts and handle plugin interrupt accordingly. Unfortunately
> > > dp_bridge_hpd_enable() bridge ops function was called to set internal_hpd
> > > flag to true later than where DP driver expected during bootup time.
> > > 
> > > This causes external DP plugin event to not get detected and display stays blank.
> > > Move enabling HDP plugin/unplugged interrupts to dp_bridge_hpd_enable()/disable() to
> > > set internal_hpd to true along with enabling HPD plugin/unplugged interrupts
> > > simultaneously to avoid timing issue during bootup and resume.
> > > 
> > > Fixes: cd198caddea7 ("drm/msm/dp: Rely on hpd_enable/disable callbacks")
> > > Signed-off-by: Kuogee Hsieh <quic_khsieh at quicinc.com>
> > > ---
> > >   drivers/gpu/drm/msm/dp/dp_display.c | 27 ++++++++++++++-------------
> > >   1 file changed, 14 insertions(+), 13 deletions(-)
> > > 
> > > diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c
> > > index 3e13acdf..71aa944 100644
> > > --- a/drivers/gpu/drm/msm/dp/dp_display.c
> > > +++ b/drivers/gpu/drm/msm/dp/dp_display.c
> > > @@ -1801,15 +1788,29 @@ void dp_bridge_hpd_enable(struct drm_bridge *bridge)
> > >   {
> > >          struct msm_dp_bridge *dp_bridge = to_dp_bridge(bridge);
> > >          struct msm_dp *dp_display = dp_bridge->dp_display;
> > > +       struct dp_display_private *dp;
> > > +
> > > +       dp = container_of(dp_display, struct dp_display_private, dp_display);
> > > 
> > >          dp_display->internal_hpd = true;
> > 
> > Can we set internal_hpd to true during probe when we see that the hpd
> > pinmux exists? Or do any of these bits toggle in the irq status register
> > when the gpio isn't muxed to "dp_hot" or the controller is for eDP and
> > it doesn't have any gpio connection internally? I'm wondering if we can
> > get by with simply enabling the "dp_hot" pin interrupts
> > (plug/unplug/replug/irq_hpd) unconditionally and not worrying about them
> > if eDP is there (because the pin doesn't exist inside the SoC), or if DP
> > HPD is being signalled out of band through type-c framework.