[PATCH v2 09/12] arm64: dts: qcom: qcm2290: Hook up interconnects
Konrad Dybcio
konrad.dybcio at linaro.org
Mon Nov 27 15:28:49 UTC 2023
Add interconnect provider nodes and hook up interconnects to consumer
devices, including bwmon.
Signed-off-by: Konrad Dybcio <konrad.dybcio at linaro.org>
---
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 248 ++++++++++++++++++++++++++++++++++
1 file changed, 248 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
index a3edc4667cc5..ce04d0acdede 100644
--- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -12,6 +12,8 @@
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interconnect/qcom,qcm2290.h>
+#include <dt-bindings/interconnect/qcom,rpm-icc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
/ {
@@ -151,6 +153,8 @@ scm: scm {
clocks = <&rpmcc RPM_SMD_CE1_CLK>;
clock-names = "core";
#reset-cells = <1>;
+ interconnects = <&system_noc MASTER_CRYPTO_CORE0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
};
};
@@ -669,6 +673,33 @@ usb_qmpphy: phy at 1615000 {
status = "disabled";
};
+ system_noc: interconnect at 1880000 {
+ compatible = "qcom,qcm2290-snoc";
+ reg = <0x0 0x01880000 0x0 0x60200>;
+ #interconnect-cells = <2>;
+
+ qup_virt: interconnect-qup {
+ compatible = "qcom,qcm2290-qup-virt";
+ #interconnect-cells = <2>;
+ };
+
+ mmnrt_virt: interconnect-mmnrt {
+ compatible = "qcom,qcm2290-mmnrt-virt";
+ #interconnect-cells = <2>;
+ };
+
+ mmrt_virt: interconnect-mmrt {
+ compatible = "qcom,qcm2290-mmrt-virt";
+ #interconnect-cells = <2>;
+ };
+ };
+
+ config_noc: interconnect at 1900000 {
+ compatible = "qcom,qcm2290-cnoc";
+ reg = <0x0 0x01900000 0x0 0x8200>;
+ #interconnect-cells = <2>;
+ };
+
qfprom at 1b44000 {
compatible = "qcom,qcm2290-qfprom", "qcom,qfprom";
reg = <0x0 0x01b44000 0x0 0x3000>;
@@ -681,6 +712,60 @@ qusb2_hstx_trim: hstx-trim at 25b {
};
};
+ pmu at 1b8e300 {
+ compatible = "qcom,qcm2290-cpu-bwmon", "qcom,sdm845-bwmon";
+ reg = <0x0 0x01b8e300 0x0 0x600>;
+ interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
+
+ operating-points-v2 = <&cpu_bwmon_opp_table>;
+ interconnects = <&bimc MASTER_APPSS_PROC RPM_ACTIVE_TAG
+ &bimc SLAVE_EBI1 RPM_ACTIVE_TAG>;
+
+ cpu_bwmon_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-0 {
+ opp-peak-kBps = <(200 * 4 * 1000)>;
+ };
+
+ opp-1 {
+ opp-peak-kBps = <(300 * 4 * 1000)>;
+ };
+
+ opp-2 {
+ opp-peak-kBps = <(451 * 4 * 1000)>;
+ };
+
+ opp-3 {
+ opp-peak-kBps = <(547 * 4 * 1000)>;
+ };
+
+ opp-4 {
+ opp-peak-kBps = <(681 * 4 * 1000)>;
+ };
+
+ opp-5 {
+ opp-peak-kBps = <(768 * 4 * 1000)>;
+ };
+
+ opp-6 {
+ opp-peak-kBps = <(1017 * 4 * 1000)>;
+ };
+
+ opp-7 {
+ opp-peak-kBps = <(1353 * 4 * 1000)>;
+ };
+
+ opp-8 {
+ opp-peak-kBps = <(1555 * 4 * 1000)>;
+ };
+
+ opp-9 {
+ opp-peak-kBps = <(1804 * 4 * 1000)>;
+ };
+ };
+ };
+
spmi_bus: spmi at 1c40000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0x0 0x01c40000 0x0 0x1100>,
@@ -721,6 +806,12 @@ rng: rng at 4453000 {
clock-names = "core";
};
+ bimc: interconnect at 4480000 {
+ compatible = "qcom,qcm2290-bimc";
+ reg = <0x0 0x04480000 0x0 0x80000>;
+ #interconnect-cells = <2>;
+ };
+
rpm_msg_ram: sram at 45f0000 {
compatible = "qcom,rpm-msg-ram";
reg = <0x0 0x045f0000 0x0 0x7000>;
@@ -756,13 +847,45 @@ sdhc_1: mmc at 4744000 {
resets = <&gcc GCC_SDCC1_BCR>;
power-domains = <&rpmpd QCM2290_VDDCX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
iommus = <&apps_smmu 0xc0 0x0>;
+ interconnects = <&system_noc MASTER_SDCC_1 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_SDCC_1 RPM_ALWAYS_TAG>;
+ interconnect-names = "sdhc-ddr",
+ "cpu-sdhc";
qcom,dll-config = <0x000f642c>;
qcom,ddr-config = <0x80040868>;
bus-width = <8>;
status = "disabled";
+
+ sdhc1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ opp-peak-kBps = <250000 133320>;
+ opp-avg-kBps = <102400 65000>;
+ };
+
+ opp-192000000 {
+ opp-hz = /bits/ 64 <192000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ opp-peak-kBps = <800000 300000>;
+ opp-avg-kBps = <204800 200000>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmpd_opp_svs_plus>;
+ opp-peak-kBps = <800000 300000>;
+ opp-avg-kBps = <204800 200000>;
+ };
+ };
};
sdhc_2: mmc at 4784000 {
@@ -786,6 +909,12 @@ sdhc_2: mmc at 4784000 {
power-domains = <&rpmpd QCM2290_VDDCX>;
operating-points-v2 = <&sdhc2_opp_table>;
iommus = <&apps_smmu 0xa0 0x0>;
+ interconnects = <&system_noc MASTER_SDCC_2 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_SDCC_2 RPM_ALWAYS_TAG>;
+ interconnect-names = "sdhc-ddr",
+ "cpu-sdhc";
qcom,dll-config = <0x0007642c>;
qcom,ddr-config = <0x80040868>;
@@ -799,11 +928,15 @@ sdhc2_opp_table: opp-table {
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
required-opps = <&rpmpd_opp_low_svs>;
+ opp-peak-kBps = <250000 133320>;
+ opp-avg-kBps = <261438 150000>;
};
opp-202000000 {
opp-hz = /bits/ 64 <202000000>;
required-opps = <&rpmpd_opp_svs_plus>;
+ opp-peak-kBps = <800000 300000>;
+ opp-avg-kBps = <261438 300000>;
};
};
};
@@ -851,6 +984,15 @@ i2c0: i2c at 4a80000 {
dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
<&gpi_dma0 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -867,6 +1009,12 @@ spi0: spi at 4a80000 {
dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
<&gpi_dma0 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -880,6 +1028,12 @@ uart0: serial at 4a80000 {
clock-names = "se";
pinctrl-0 = <&qup_uart0_default>;
pinctrl-names = "default";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
status = "disabled";
};
@@ -894,6 +1048,15 @@ i2c1: i2c at 4a84000 {
dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
<&gpi_dma0 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -910,6 +1073,12 @@ spi1: spi at 4a84000 {
dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
<&gpi_dma0 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -926,6 +1095,15 @@ i2c2: i2c at 4a88000 {
dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
<&gpi_dma0 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -942,6 +1120,12 @@ spi2: spi at 4a88000 {
dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
<&gpi_dma0 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -958,6 +1142,15 @@ i2c3: i2c at 4a8c000 {
dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
<&gpi_dma0 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -974,6 +1167,12 @@ spi3: spi at 4a8c000 {
dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
<&gpi_dma0 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -990,6 +1189,15 @@ i2c4: i2c at 4a90000 {
dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
<&gpi_dma0 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1006,6 +1214,12 @@ spi4: spi at 4a90000 {
dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
<&gpi_dma0 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1019,6 +1233,12 @@ uart4: serial at 4a90000 {
clock-names = "se";
pinctrl-0 = <&qup_uart4_default>;
pinctrl-names = "default";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
status = "disabled";
};
@@ -1033,6 +1253,15 @@ i2c5: i2c at 4a94000 {
dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
<&gpi_dma0 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1049,6 +1278,12 @@ spi5: spi at 4a94000 {
dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
<&gpi_dma0 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1081,6 +1316,13 @@ usb: usb at 4ef8800 {
resets = <&gcc GCC_USB30_PRIM_BCR>;
power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+ /* TODO: USB<->IPA path */
+ interconnects = <&system_noc MASTER_USB3_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_USB3 RPM_ALWAYS_TAG>;
+ interconnect-names = "usb-ddr",
+ "apps-usb";
wakeup-source;
#address-cells = <2>;
@@ -1127,6 +1369,12 @@ mdss: display-subsystem at 5e00000 {
iommus = <&apps_smmu 0x420 0x2>,
<&apps_smmu 0x421 0x0>;
+ interconnects = <&mmrt_virt MASTER_MDP0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_DISPLAY_CFG RPM_ALWAYS_TAG>;
+ interconnect-names = "mdp0-mem",
+ "cpu-cfg";
#address-cells = <2>;
#size-cells = <2>;
--
2.43.0
More information about the dri-devel
mailing list