[PATCH 0/7] drm/msm: Initial fixes for DUALPIPE (+DSC) topology

[Marijn Suijten]

This series covers a step-up towards supporting the DUALPIPE DSC
topology, also known as 2:2:2 topology (on active-CTL hardware).  It
involves 2 layer mixers, 2 DSC compression encoders, and 2 interfaces
(on DSI, this is called bonded-DSI) where bandwidth constraints (e.g. 4k
panels at 120Hz) require two interfaces to transmit pixel data.

Enabling this topology will be hard(er) than downstream as hacking a
layout type in DTS won't be describing the hardware, but "dynamically"
determining it at runtime may pose some of a challenge that is left to a
future series.  Such changes will also involve the 1:1:1 topology needed
for constrained hardware like the Fairphone 5 on SC7280 with access to
only one DSC encoder and thus ruled out of the current 2:2:1 topology.

Likewise, the patches and discussions around improving active-CTL
configuration to support bonded interfaces (that share a single CTL
block) are still in full swing and hence elided from this series, apart
from one patch to fix the ACTIVE_DSC register coding to support updates,
so that it is not forgotten about.

Note that some patches are applicable to DSC-less DUALPIPE bonded mode
as well, such as the patch that allows the slave interface to always be
flushed as that is only supposed to be excluded in the yet-unsupported
PPSPLIT topology.

This series also contains some patches that I'm not too sure about:

  drm/msm/dpu: Correct dual-ctl -> dual-intf typo in comment

    Downstream doesn't skip the slave INTF flush on active-CTL [1]
    (again, just like cmdmode, only when PPSPLIT is enabled [2]), and
    even added an extra comment [1] explaining this case.  Hence a
    dual-intf but single-flush case doesn't seem to exist as there's
    only one CTL according to the remainder of the comment.
    Maybe the whole comment is wrong?

  drm/msm/dsi: Set PHY usescase before registering DSI host

    It seems intentional to only set the usecase after
    msm_dsi_host_register() in case it fails, so maybe a non-zero `ret`
    here should reset the usecase?  Likewise should the function call be
    moved in !IS_BONDED_DSI() above?

    Ideally we also understand what I am doing differently (maybe
    wrongly) in my panel driver that makes the PLL turn on and configure
    before the usecase has been set, even though these calls are messy
    and error-prone nevertheless.

[1]: https://git.codelinaro.org/clo/la/platform/vendor/opensource/display-drivers/-/blob/display-kernel.lnx.5.4.r1-rel/msm/sde/sde_encoder_phys_vid.c?ref_type=heads#L794-804
[2]: https://git.codelinaro.org/clo/la/platform/vendor/opensource/display-drivers/-/blob/display-kernel.lnx.5.4.r1-rel/msm/sde/sde_encoder_phys_cmd.c?ref_type=heads#L1131-1139

Signed-off-by: Marijn Suijten <marijn.suijten at somainline.org>
---
Marijn Suijten (7):
      drm/msm/dsi: Print dual-DSI-adjusted pclk instead of original mode pclk
      drm/msm/dsi: Pass bonded-DSI hdisplay/2 to DSC timing configuration
      drm/msm/dpu: Always flush the slave INTF on the CTL
      drm/msm/dpu: Allow configuring multiple active DSC blocks
      drm/msm/dpu: Correct dual-ctl -> dual-intf typo in comment
      drm/msm/dsi: Set PHY usescase before registering DSI host
      drm/msm/dpu: Rename `ctx` parameter to `intf` to match other functions

 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c |  3 ---
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c |  2 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c           |  9 ++++++---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c          | 14 +++++++-------
 drivers/gpu/drm/msm/dsi/dsi_host.c                   | 14 +++++++-------
 drivers/gpu/drm/msm/dsi/dsi_manager.c                | 15 +++++++++++----
 6 files changed, 32 insertions(+), 25 deletions(-)
---
base-commit: 6bd343537461b57f3efe5dfc5fc193a232dfef1e
change-id: 20240416-drm-msm-initial-dualpipe-dsc-fixes-3f0715b03bf4

Best regards,
-- 
Marijn Suijten <marijn.suijten at somainline.org>