[PATCH v1 08/12] media: ivtv: Make I2C terminology more inclusive

Easwar Hariharan eahariha at linux.microsoft.com
Tue Apr 30 17:38:07 UTC 2024


I2C v7, SMBus 3.2, and I3C 1.1.1 specifications have replaced "master/slave"
with more appropriate terms. Inspired by and following on to Wolfram's
series to fix drivers/i2c/[1], fix the terminology for users of
I2C_ALGOBIT bitbanging interface, now that the approved verbiage exists
in the specification.

Compile tested, no functionality changes intended

[1]: https://lore.kernel.org/all/20240322132619.6389-1-wsa+renesas@sang-engineering.com/

Signed-off-by: Easwar Hariharan <eahariha at linux.microsoft.com>
---
 drivers/media/pci/ivtv/ivtv-i2c.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/media/pci/ivtv/ivtv-i2c.c b/drivers/media/pci/ivtv/ivtv-i2c.c
index c052c57c6dce..967e6a025020 100644
--- a/drivers/media/pci/ivtv/ivtv-i2c.c
+++ b/drivers/media/pci/ivtv/ivtv-i2c.c
@@ -33,14 +33,14 @@
     Some more general comments about what we are doing:
 
     The i2c bus is a 2 wire serial bus, with clock (SCL) and data (SDA)
-    lines.  To communicate on the bus (as a master, we don't act as a slave),
+    lines.  To communicate on the bus (as a host, we don't act as a client),
     we first initiate a start condition (ivtv_start).  We then write the
     address of the device that we want to communicate with, along with a flag
-    that indicates whether this is a read or a write.  The slave then issues
+    that indicates whether this is a read or a write.  The client then issues
     an ACK signal (ivtv_ack), which tells us that it is ready for reading /
     writing.  We then proceed with reading or writing (ivtv_read/ivtv_write),
     and finally issue a stop condition (ivtv_stop) to make the bus available
-    to other masters.
+    to other hosts.
 
     There is an additional form of transaction where a write may be
     immediately followed by a read.  In this case, there is no intervening
@@ -379,7 +379,7 @@ static int ivtv_waitsda(struct ivtv *itv, int val)
 	return 0;
 }
 
-/* Wait for the slave to issue an ACK */
+/* Wait for the client to issue an ACK */
 static int ivtv_ack(struct ivtv *itv)
 {
 	int ret = 0;
@@ -407,7 +407,7 @@ static int ivtv_ack(struct ivtv *itv)
 	return ret;
 }
 
-/* Write a single byte to the i2c bus and wait for the slave to ACK */
+/* Write a single byte to the i2c bus and wait for the client to ACK */
 static int ivtv_sendbyte(struct ivtv *itv, unsigned char byte)
 {
 	int i, bit;
@@ -471,7 +471,7 @@ static int ivtv_readbyte(struct ivtv *itv, unsigned char *byte, int nack)
 	return 0;
 }
 
-/* Issue a start condition on the i2c bus to alert slaves to prepare for
+/* Issue a start condition on the i2c bus to alert clients to prepare for
    an address write */
 static int ivtv_start(struct ivtv *itv)
 {
@@ -534,7 +534,7 @@ static int ivtv_stop(struct ivtv *itv)
 	return 0;
 }
 
-/* Write a message to the given i2c slave.  do_stop may be 0 to prevent
+/* Write a message to the given i2c client.  do_stop may be 0 to prevent
    issuing the i2c stop condition (when following with a read) */
 static int ivtv_write(struct ivtv *itv, unsigned char addr, unsigned char *data, u32 len, int do_stop)
 {
@@ -558,7 +558,7 @@ static int ivtv_write(struct ivtv *itv, unsigned char addr, unsigned char *data,
 	return ret;
 }
 
-/* Read data from the given i2c slave.  A stop condition is always issued. */
+/* Read data from the given i2c client.  A stop condition is always issued. */
 static int ivtv_read(struct ivtv *itv, unsigned char addr, unsigned char *data, u32 len)
 {
 	int retry, ret = -EREMOTEIO;
-- 
2.34.1



More information about the dri-devel mailing list