[PATCH 3/8] clk: qcom: clk-alpha-pll: Add HUAYRA_2290 support

[Andrew Halaney]

On Mon, Feb 19, 2024 at 02:35:48PM +0100, Konrad Dybcio wrote:
> Commit 134b55b7e19f ("clk: qcom: support Huayra type Alpha PLL")
> introduced an entry to the alpha offsets array, but diving into QCM2290
> downstream and some documentation, it turned out that the name Huayra
> apparently has been used quite liberally across many chips, even with
> noticeably different hardware.
> 
> Introduce another set of offsets and a new configure function for the
> Huayra PLL found on QCM2290. This is required e.g. for the consumers
> of GPUCC_PLL0 to properly start.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio at linaro.org>
> ---
>  drivers/clk/qcom/clk-alpha-pll.c | 45 ++++++++++++++++++++++++++++++++++++++++
>  drivers/clk/qcom/clk-alpha-pll.h |  3 +++
>  2 files changed, 48 insertions(+)
> 
> diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
> index 8a412ef47e16..61b5abd13782 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.c
> +++ b/drivers/clk/qcom/clk-alpha-pll.c
> @@ -244,6 +244,19 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
>  		[PLL_OFF_OPMODE] = 0x30,
>  		[PLL_OFF_STATUS] = 0x3c,
>  	},
> +	[CLK_ALPHA_PLL_TYPE_HUAYRA_2290] =  {
> +		[PLL_OFF_L_VAL] = 0x04,
> +		[PLL_OFF_ALPHA_VAL] = 0x08,
> +		[PLL_OFF_USER_CTL] = 0x0c,
> +		[PLL_OFF_CONFIG_CTL] = 0x10,
> +		[PLL_OFF_CONFIG_CTL_U] = 0x14,
> +		[PLL_OFF_CONFIG_CTL_U1] = 0x18,
> +		[PLL_OFF_TEST_CTL] = 0x1c,
> +		[PLL_OFF_TEST_CTL_U] = 0x20,
> +		[PLL_OFF_TEST_CTL_U1] = 0x24,
> +		[PLL_OFF_OPMODE] = 0x28,
> +		[PLL_OFF_STATUS] = 0x38,
> +	},
>  };
>  EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
>  
> @@ -779,6 +792,38 @@ static long clk_alpha_pll_round_rate(struct clk_hw *hw, unsigned long rate,
>  	return clamp(rate, min_freq, max_freq);
>  }
>  
> +void clk_huayra_2290_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> +				   const struct alpha_pll_config *config)
> +{
> +	clk_alpha_pll_write_config(regmap, PLL_CONFIG_CTL(pll), config->config_ctl_val);
> +	clk_alpha_pll_write_config(regmap, PLL_CONFIG_CTL_U(pll), config->config_ctl_hi_val);
> +	clk_alpha_pll_write_config(regmap, PLL_CONFIG_CTL_U1(pll), config->config_ctl_hi1_val);
> +	clk_alpha_pll_write_config(regmap, PLL_TEST_CTL(pll), config->test_ctl_val);
> +	clk_alpha_pll_write_config(regmap, PLL_TEST_CTL_U(pll), config->test_ctl_hi_val);
> +	clk_alpha_pll_write_config(regmap, PLL_TEST_CTL_U1(pll), config->test_ctl_hi1_val);
> +	clk_alpha_pll_write_config(regmap, PLL_L_VAL(pll), config->l);
> +	clk_alpha_pll_write_config(regmap, PLL_ALPHA_VAL(pll), config->alpha);
> +	clk_alpha_pll_write_config(regmap, PLL_USER_CTL(pll), config->user_ctl_val);
> +
> +	/* Set PLL_BYPASSNL */
> +	regmap_update_bits(regmap, PLL_MODE(pll), PLL_BYPASSNL, PLL_BYPASSNL);
> +
> +	/* Wait 5 us between setting BYPASS and deasserting reset */
> +	mb();
> +	udelay(5);
> +
> +	/* Take PLL out from reset state */
> +	regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
> +
> +	/* Wait 50us for PLL_LOCK_DET bit to go high */
> +	mb();
> +	usleep_range(50, 55);

I *think* you'd want to use a read to ensure your write goes through
prior to your sleep... from memory-barriers.txt:

	5. A readX() by a CPU thread from the peripheral will complete before
	   any subsequent delay() loop can begin execution on the same thread.
	   This ensures that two MMIO register writes by the CPU to a peripheral
	   will arrive at least 1us apart if the first write is immediately read
	   back with readX() and udelay(1) is called prior to the second
	   writeX():

		writel(42, DEVICE_REGISTER_0); // Arrives at the device...
		readl(DEVICE_REGISTER_0);
		udelay(1);
		writel(42, DEVICE_REGISTER_1); // ...at least 1us before this.

also https://youtu.be/i6DayghhA8Q?si=7lp0be35q1HRmlnV&t=1677
for more references on this topic.


> +
> +	/* Enable PLL output */
> +	regmap_update_bits(regmap, PLL_MODE(pll), PLL_OUTCTRL, PLL_OUTCTRL);
> +}
> +EXPORT_SYMBOL(clk_huayra_2290_pll_configure);
> +
>  static unsigned long
>  alpha_huayra_pll_calc_rate(u64 prate, u32 l, u32 a)
>  {
> diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
> index fb6d50263bb9..91d3d6f19eae 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.h
> +++ b/drivers/clk/qcom/clk-alpha-pll.h
> @@ -29,6 +29,7 @@ enum {
>  	CLK_ALPHA_PLL_TYPE_BRAMMO_EVO,
>  	CLK_ALPHA_PLL_TYPE_STROMER,
>  	CLK_ALPHA_PLL_TYPE_STROMER_PLUS,
> +	CLK_ALPHA_PLL_TYPE_HUAYRA_2290,
>  	CLK_ALPHA_PLL_TYPE_MAX,
>  };
>  
> @@ -191,6 +192,8 @@ extern const struct clk_ops clk_alpha_pll_rivian_evo_ops;
>  
>  void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
>  			     const struct alpha_pll_config *config);
> +void clk_huayra_2290_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> +				   const struct alpha_pll_config *config);
>  void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
>  				const struct alpha_pll_config *config);
>  void clk_trion_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> 
> -- 
> 2.43.2
> 
>