[PATCH 09/11] usb: dwc2: Skip clock gating on Broadcom SoCs

[Lukas Wunner]

On Thu, Jul 04, 2024 at 03:14:50PM +0100, Florian Fainelli wrote:
> On 6/30/2024 4:36 PM, Stefan Wahren wrote:
> > On resume of the Raspberry Pi the dwc2 driver fails to enable
> > HCD_FLAG_HW_ACCESSIBLE before re-enabling the interrupts.
> > This causes a situation where both handler ignore a incoming port
> > interrupt and force the upper layers to disable the dwc2 interrupt line.
> > This leaves the USB interface in a unusable state:
> > 
> > irq 66: nobody cared (try booting with the "irqpoll" option)
> > CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W          6.10.0-rc3
> > Hardware name: BCM2835
> > Call trace:
> > unwind_backtrace from show_stack+0x10/0x14
> > show_stack from dump_stack_lvl+0x50/0x64
> > dump_stack_lvl from __report_bad_irq+0x38/0xc0
> > __report_bad_irq from note_interrupt+0x2ac/0x2f4
> > note_interrupt from handle_irq_event+0x88/0x8c
> > handle_irq_event from handle_level_irq+0xb4/0x1ac
> > handle_level_irq from generic_handle_domain_irq+0x24/0x34
> > generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
> > bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
> > generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
> > generic_handle_arch_irq from __irq_svc+0x88/0xb0

A similar issue was reported for Agilex platforms back in 2021:

https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/

It was fixed by commit 3d8d3504d233 ("usb: dwc2: Add platform specific
data for Intel's Agilex"), which sets the no_clock_gating flag on that
platform.

Looking at drivers/usb/dwc2/params.c, numerous other platforms need
the same flag.

Please amend the commit message to mention the Agilex issue and
resulting commit.


> > --- a/drivers/usb/dwc2/params.c
> > +++ b/drivers/usb/dwc2/params.c
> > @@ -23,6 +23,7 @@ static void dwc2_set_bcm_params(struct dwc2_hsotg *hsotg)
> >   	p->max_transfer_size = 65535;
> >   	p->max_packet_count = 511;
> >   	p->ahbcfg = 0x10;
> > +	p->no_clock_gating = true;
> 
> Could we set this depending upon whether the dwc2 host controller is a
> wake-up source for the system or not?

The flag seems to mean whether the platform is actually capable of
disabling the clock of the USB controller.  BCM2835 seems to be
incapable and as a result, even though dwc2_host_enter_clock_gating()
is called, the chip signals interrupts.

There doesn't seem to be a relation to using the controller as a
wakeup source, so your comment doesn't seem to make sense.
If the clock can't be gated, the chip can always serve as a
wakeup source.

The real question is whether BCM2848 platforms likewise cannot disable
the clock of the dwc2 controller or whether this is specific to the
BCM2835.  Right now dwc2_set_bcm_params() is applied to both the
BCM2848 and BCM2835.  If the BCM2848 behaves differently in this
regard, we'd have to duplicate dwc2_set_bcm_params() for the BCM2835.

Thanks,

Lukas