[PATCH v3 18/23] regulator: add s2dos05 regulator support
Dzmitry Sankouski
dsankouski at gmail.com
Tue Jun 18 13:59:52 UTC 2024
S2dos05 has 1 buck and 4 LDO regulators, used for powering
panel/touchscreen.
Signed-off-by: Dzmitry Sankouski <dsankouski at gmail.com>
---
MAINTAINERS | 1 +
drivers/regulator/Kconfig | 8 +
drivers/regulator/Makefile | 1 +
drivers/regulator/s2dos05-regulator.c | 362 ++++++++++++++++++++++++++++++++++
4 files changed, 372 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index b53462684a30..bee700a5e648 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19910,6 +19910,7 @@ F: Documentation/devicetree/bindings/regulator/samsung,s5m*.yaml
F: drivers/clk/clk-s2mps11.c
F: drivers/mfd/s2dos*.c
F: drivers/mfd/sec*.c
+F: drivers/regulator/s2dos*.c
F: drivers/regulator/s2m*.c
F: drivers/regulator/s5m*.c
F: drivers/rtc/rtc-s5m.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index d333be2bea3b..d6d6f571a65d 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1297,6 +1297,14 @@ config REGULATOR_RTQ2208
and two ldos. It features wide output voltage range from 0.4V to 2.05V
and the capability to configure the corresponding power stages.
+config REGULATOR_S2DOS05
+ tristate "SLSI S2DOS05 regulator"
+ depends on MFD_S2DOS_CORE || COMPILE_TEST
+ help
+ This driver provides support for the voltage regulators of the S2DOS05.
+ The S2DOS05 is a companion power management IC for the smart phones.
+ The S2DOS05 has 4 LDOs and 1 BUCK outputs.
+
config REGULATOR_S2MPA01
tristate "Samsung S2MPA01 voltage regulator"
depends on MFD_SEC_CORE || COMPILE_TEST
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index ba15fa5f30ad..80f889404597 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -151,6 +151,7 @@ obj-$(CONFIG_REGULATOR_RTMV20) += rtmv20-regulator.o
obj-$(CONFIG_REGULATOR_RTQ2134) += rtq2134-regulator.o
obj-$(CONFIG_REGULATOR_RTQ6752) += rtq6752-regulator.o
obj-$(CONFIG_REGULATOR_RTQ2208) += rtq2208-regulator.o
+obj-$(CONFIG_REGULATOR_S2DOS05) += s2dos05-regulator.o
obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
diff --git a/drivers/regulator/s2dos05-regulator.c b/drivers/regulator/s2dos05-regulator.c
new file mode 100644
index 000000000000..3c58a1bd2262
--- /dev/null
+++ b/drivers/regulator/s2dos05-regulator.c
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * s2dos05.c - Regulator driver for the Samsung s2dos05
+ *
+ * Copyright (C) 2016 Samsung Electronics
+ * Copyright (C) 2023 Dzmitry Sankouski <dsankouski at gmail.com>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/bug.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/mfd/samsung/s2dos-core.h>
+#include <linux/mfd/samsung/s2dos05.h>
+#include <linux/i2c.h>
+#include <linux/debugfs.h>
+
+struct s2dos05_data {
+ struct regmap *regmap;
+ struct device *dev;
+};
+
+static int s2m_enable(struct regulator_dev *rdev)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+
+ return regmap_update_bits(regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask,
+ rdev->desc->enable_mask);
+}
+
+static int s2m_disable_regmap(struct regulator_dev *rdev)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+ u8 val;
+
+ if (rdev->desc->enable_is_inverted)
+ val = rdev->desc->enable_mask;
+ else
+ val = 0;
+
+ return regmap_update_bits(regmap, rdev->desc->enable_reg, rdev->desc->enable_mask,
+ val);
+}
+
+static int s2m_is_enabled_regmap(struct regulator_dev *rdev)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+ int ret;
+ unsigned int val;
+
+ ret = regmap_read(regmap, rdev->desc->enable_reg, &val);
+ if (ret < 0)
+ return ret;
+
+ if (rdev->desc->enable_is_inverted)
+ return (val & rdev->desc->enable_mask) == 0;
+ else
+ return (val & rdev->desc->enable_mask) != 0;
+}
+
+static int s2m_get_voltage_sel_regmap(struct regulator_dev *rdev)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+ int ret;
+ unsigned int val;
+
+ ret = regmap_read(regmap, rdev->desc->vsel_reg, &val);
+ if (ret < 0)
+ return ret;
+
+ val &= rdev->desc->vsel_mask;
+
+ return val;
+}
+
+static int s2m_set_voltage_sel_regmap(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+ int ret;
+
+ ret = regmap_update_bits(regmap, rdev->desc->vsel_reg, rdev->desc->vsel_mask,
+ sel);
+ if (ret < 0)
+ goto out;
+
+ if (rdev->desc->apply_bit)
+ ret = regmap_update_bits(regmap, rdev->desc->apply_reg,
+ rdev->desc->apply_bit,
+ rdev->desc->apply_bit);
+ return ret;
+out:
+ pr_warn("%s: failed to set voltage_sel_regmap\n", rdev->desc->name);
+ return ret;
+}
+
+static int s2m_set_voltage_sel_regmap_buck(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+ int ret;
+
+ ret = regmap_write(regmap, rdev->desc->vsel_reg, sel);
+ if (ret < 0)
+ goto out;
+
+ if (rdev->desc->apply_bit)
+ ret = regmap_update_bits(regmap, rdev->desc->apply_reg,
+ rdev->desc->apply_bit,
+ rdev->desc->apply_bit);
+ return ret;
+out:
+ pr_warn("%s: failed to set voltage_sel_regmap\n", rdev->desc->name);
+ return ret;
+}
+
+static int s2m_set_voltage_time_sel(struct regulator_dev *rdev,
+ unsigned int old_selector,
+ unsigned int new_selector)
+{
+ int old_volt, new_volt;
+
+ /* sanity check */
+ if (!rdev->desc->ops->list_voltage)
+ return -EINVAL;
+
+ old_volt = rdev->desc->ops->list_voltage(rdev, old_selector);
+ new_volt = rdev->desc->ops->list_voltage(rdev, new_selector);
+
+ if (old_selector < new_selector)
+ return DIV_ROUND_UP(new_volt - old_volt, S2DOS05_RAMP_DELAY);
+
+ return 0;
+}
+
+static int s2m_set_active_discharge(struct regulator_dev *rdev,
+ bool enable)
+{
+ struct s2dos05_data *info = rdev_get_drvdata(rdev);
+ struct regmap *regmap = info->regmap;
+ int ret;
+ u8 val;
+
+ if (enable)
+ val = rdev->desc->active_discharge_on;
+ else
+ val = rdev->desc->active_discharge_off;
+
+ ret = regmap_update_bits(regmap, rdev->desc->active_discharge_reg,
+ rdev->desc->active_discharge_mask, val);
+ return ret;
+}
+
+static const struct regulator_ops s2dos05_ldo_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .is_enabled = s2m_is_enabled_regmap,
+ .enable = s2m_enable,
+ .disable = s2m_disable_regmap,
+ .get_voltage_sel = s2m_get_voltage_sel_regmap,
+ .set_voltage_sel = s2m_set_voltage_sel_regmap,
+ .set_voltage_time_sel = s2m_set_voltage_time_sel,
+ .set_active_discharge = s2m_set_active_discharge,
+};
+
+static const struct regulator_ops s2dos05_buck_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .is_enabled = s2m_is_enabled_regmap,
+ .enable = s2m_enable,
+ .disable = s2m_disable_regmap,
+ .get_voltage_sel = s2m_get_voltage_sel_regmap,
+ .set_voltage_sel = s2m_set_voltage_sel_regmap_buck,
+ .set_voltage_time_sel = s2m_set_voltage_time_sel,
+ .set_active_discharge = s2m_set_active_discharge,
+};
+
+#define _BUCK(macro) S2DOS05_BUCK##macro
+#define _buck_ops(num) s2dos05_buck_ops##num
+
+#define _LDO(macro) S2DOS05_LDO##macro
+#define _REG(ctrl) S2DOS05_REG##ctrl
+#define _ldo_ops(num) s2dos05_ldo_ops##num
+#define _MASK(macro) S2DOS05_ENABLE_MASK##macro
+#define _TIME(macro) S2DOS05_ENABLE_TIME##macro
+
+#define BUCK_DESC(_name, _id, _ops, m, s, v, e, em, t, a) { \
+ .name = _name, \
+ .id = _id, \
+ .ops = _ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = m, \
+ .uV_step = s, \
+ .n_voltages = S2DOS05_BUCK_N_VOLTAGES, \
+ .vsel_reg = v, \
+ .vsel_mask = S2DOS05_BUCK_VSEL_MASK, \
+ .enable_reg = e, \
+ .enable_mask = em, \
+ .enable_time = t, \
+ .active_discharge_off = 0, \
+ .active_discharge_on = S2DOS05_BUCK_FD_MASK, \
+ .active_discharge_reg = a, \
+ .active_discharge_mask = S2DOS05_BUCK_FD_MASK \
+}
+
+#define LDO_DESC(_name, _id, _ops, m, s, v, e, em, t, a) { \
+ .name = _name, \
+ .id = _id, \
+ .ops = _ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = m, \
+ .uV_step = s, \
+ .n_voltages = S2DOS05_LDO_N_VOLTAGES, \
+ .vsel_reg = v, \
+ .vsel_mask = S2DOS05_LDO_VSEL_MASK, \
+ .enable_reg = e, \
+ .enable_mask = em, \
+ .enable_time = t, \
+ .active_discharge_off = 0, \
+ .active_discharge_on = S2DOS05_LDO_FD_MASK, \
+ .active_discharge_reg = a, \
+ .active_discharge_mask = S2DOS05_LDO_FD_MASK \
+}
+
+static struct regulator_desc regulators[S2DOS05_REGULATOR_MAX] = {
+ /* name, id, ops, min_uv, uV_step, vsel_reg, enable_reg */
+ LDO_DESC("ldo1", _LDO(1), &_ldo_ops(), _LDO(_MIN1),
+ _LDO(_STEP1), _REG(_LDO1_CFG),
+ _REG(_EN), _MASK(_L1), _TIME(_LDO), _REG(_LDO1_CFG)),
+ LDO_DESC("ldo2", _LDO(2), &_ldo_ops(), _LDO(_MIN1),
+ _LDO(_STEP1), _REG(_LDO2_CFG),
+ _REG(_EN), _MASK(_L2), _TIME(_LDO), _REG(_LDO2_CFG)),
+ LDO_DESC("ldo3", _LDO(3), &_ldo_ops(), _LDO(_MIN2),
+ _LDO(_STEP1), _REG(_LDO3_CFG),
+ _REG(_EN), _MASK(_L3), _TIME(_LDO), _REG(_LDO3_CFG)),
+ LDO_DESC("ldo4", _LDO(4), &_ldo_ops(), _LDO(_MIN2),
+ _LDO(_STEP1), _REG(_LDO4_CFG),
+ _REG(_EN), _MASK(_L4), _TIME(_LDO), _REG(_LDO4_CFG)),
+ BUCK_DESC("buck1", _BUCK(1), &_buck_ops(), _BUCK(_MIN1),
+ _BUCK(_STEP1), _REG(_BUCK_VOUT),
+ _REG(_EN), _MASK(_B1), _TIME(_BUCK), _REG(_BUCK_CFG)),
+};
+
+static int s2dos05_pmic_dt_parse_pdata(struct device *dev,
+ struct of_regulator_match *rdata,
+ unsigned int rdev_num)
+{
+ struct device_node *reg_np;
+ int err;
+
+ reg_np = of_get_child_by_name(dev->parent->of_node, "regulators");
+ if (!reg_np) {
+ dev_err(dev, "could not find regulators sub-node\n");
+ return -EINVAL;
+ }
+
+ err = of_regulator_match(dev, reg_np, rdata, rdev_num);
+ of_node_put(reg_np);
+
+ return err;
+}
+
+static int s2dos05_pmic_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct s2dos_core *iodev = dev_get_drvdata(pdev->dev.parent);
+ struct of_regulator_match *rdata = NULL;
+ struct s2dos05_data *s2dos05;
+ struct regulator_config config = { };
+ unsigned int rdev_num = ARRAY_SIZE(regulators);
+ int i;
+ int ret, err = 0;
+
+ s2dos05 = devm_kzalloc(dev, sizeof(struct s2dos05_data),
+ GFP_KERNEL);
+ if (!s2dos05) {
+ ret = -ENOMEM;
+ goto err_data;
+ }
+ platform_set_drvdata(pdev, s2dos05);
+
+ rdata = kcalloc(rdev_num, sizeof(*rdata), GFP_KERNEL);
+ if (!rdata)
+ return -ENOMEM;
+
+ for (i = 0; i < rdev_num; i++)
+ rdata[i].name = regulators[i].name;
+
+ err = s2dos05_pmic_dt_parse_pdata(dev, rdata, rdev_num);
+ if (err < 0) {
+ dev_err(dev, "Failed to parse regulators device of_node\n");
+ goto err_data;
+ }
+
+ s2dos05->regmap = iodev->regmap;
+ s2dos05->dev = dev;
+
+ for (i = 0; i < rdev_num; i++) {
+ struct regulator_dev *regulator;
+
+ config.init_data = rdata[i].init_data;
+ config.of_node = rdata[i].of_node;
+ config.dev = dev;
+ config.driver_data = s2dos05;
+ regulator = devm_regulator_register(&pdev->dev,
+ ®ulators[i], &config);
+ if (IS_ERR(regulator)) {
+ ret = PTR_ERR(regulator);
+ dev_err(&pdev->dev, "regulator init failed for %d\n",
+ i);
+ goto out;
+ }
+ }
+
+out:
+ kfree(rdata);
+
+ return ret;
+
+err_data:
+ devm_kfree(dev, (void *)s2dos05);
+ kfree(s2dos05);
+
+ return ret;
+}
+
+static const struct platform_device_id s2dos05_pmic_id[] = {
+ { "s2dos05-regulator" },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, s2dos05_pmic_id);
+
+static struct platform_driver s2dos05_platform_driver = {
+ .driver = {
+ .name = "s2dos05",
+ },
+ .probe = s2dos05_pmic_probe,
+ .id_table = s2dos05_pmic_id,
+};
+module_platform_driver(s2dos05_platform_driver);
+
+MODULE_AUTHOR("Dzmitry Sankouski <dsankouski at gmail.com>");
+MODULE_DESCRIPTION("SAMSUNG s2dos05 Regulator Driver");
+MODULE_LICENSE("GPL");
--
2.39.2
More information about the dri-devel
mailing list