[PATCH 3/3] drm/panel: add lincoln lcd197 support

Dmitry Baryshkov dmitry.baryshkov at linaro.org
Wed Jun 26 04:41:45 UTC 2024


On Tue, Jun 25, 2024 at 04:25:50PM GMT, Jerome Brunet wrote:
> Add support for the Lincoln LCD197 1080x1920 DSI panel.
> 
> Signed-off-by: Jerome Brunet <jbrunet at baylibre.com>
> ---
>  drivers/gpu/drm/panel/Kconfig                |  11 +
>  drivers/gpu/drm/panel/Makefile               |   1 +
>  drivers/gpu/drm/panel/panel-lincoln-lcd197.c | 333 +++++++++++++++++++
>  3 files changed, 345 insertions(+)
>  create mode 100644 drivers/gpu/drm/panel/panel-lincoln-lcd197.c
> 

[...]

> +
> +	mipi_dsi_dcs_write_seq(lcd->dsi, 0xB9, 0xFF, 0x83, 0x99);

- Please use lowercase hex instead
- Please consider switching to _multi() functions.


> +	usleep_range(200, 300);

This will require new helper msm_dsi_usleep_range(ctx, 200, 300);

> +	mipi_dsi_dcs_write_seq(lcd->dsi, 0xB6, 0x92, 0x92);
> +	mipi_dsi_dcs_write_seq(lcd->dsi, 0xCC, 0x00);
> +	mipi_dsi_dcs_write_seq(lcd->dsi, 0xBF, 0x40, 0x41, 0x50, 0x49);
> +	mipi_dsi_dcs_write_seq(lcd->dsi, 0xC6, 0xFF, 0xF9);
> +	mipi_dsi_dcs_write_seq(lcd->dsi, 0xC0, 0x25, 0x5A);
> +	mipi_dsi_dcs_write_seq(lcd->dsi, MIPI_DCS_SET_ADDRESS_MODE, 0x02);
> +
> +	err = mipi_dsi_dcs_exit_sleep_mode(lcd->dsi);
> +	if (err < 0) {
> +		dev_err(panel->dev, "failed to exit sleep mode: %d\n", err);
> +		goto poweroff;
> +	}
> +	msleep(120);
> +
> +	err = mipi_dsi_dcs_read(lcd->dsi, MIPI_DCS_GET_DISPLAY_ID, display_id, 3);

This probably needs new _multi helper too.

> +	if (err < 0) {
> +		dev_err(panel->dev, "Failed to read display id: %d\n", err);
> +	} else {
> +		dev_dbg(panel->dev, "Display id: 0x%02x-0x%02x-0x%02x\n",
> +			display_id[0], display_id[1], display_id[2]);
> +	}
> +
> +	lcd->prepared = true;

Should not be required anymore.

> +
> +	return 0;
> +
> +poweroff:
> +	gpiod_set_value_cansleep(lcd->enable_gpio, 0);
> +	gpiod_set_value_cansleep(lcd->reset_gpio, 1);
> +	regulator_disable(lcd->supply);
> +
> +	return err;
> +}
> +

> +
> +static const struct drm_display_mode default_mode = {
> +	.clock = 154002,
> +	.hdisplay = 1080,
> +	.hsync_start = 1080 + 20,
> +	.hsync_end = 1080 + 20 + 6,
> +	.htotal = 1080 + 204,
> +	.vdisplay = 1920,
> +	.vsync_start = 1920 + 4,
> +	.vsync_end = 1920 + 4 + 4,
> +	.vtotal = 1920 + 79,
> +	.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> +};
> +
> +static int lincoln_lcd197_panel_get_modes(struct drm_panel *panel,
> +					  struct drm_connector *connector)
> +{
> +	struct drm_display_mode *mode;
> +
> +	mode = drm_mode_duplicate(connector->dev, &default_mode);
> +	if (!mode) {
> +		dev_err(panel->dev, "failed to add mode %ux%u@%u\n",
> +			default_mode.hdisplay, default_mode.vdisplay,
> +			drm_mode_vrefresh(&default_mode));
> +		return -ENOMEM;
> +	}
> +
> +	drm_mode_set_name(mode);
> +	drm_mode_probed_add(connector, mode);
> +	connector->display_info.width_mm = 79;
> +	connector->display_info.height_mm = 125;

drm_connector_helper_get_modes_fixed()

> +
> +	return 1;
> +}
> +


> +
> +static void lincoln_lcd197_panel_shutdown(struct mipi_dsi_device *dsi)
> +{
> +	struct lincoln_lcd197_panel *lcd = mipi_dsi_get_drvdata(dsi);
> +
> +	drm_panel_disable(&lcd->panel);
> +	drm_panel_unprepare(&lcd->panel);
> +}

I think the agreement was that there should be no need for the panel's
shutdown, the DRM driver should shutdown the panel.


-- 
With best wishes
Dmitry


More information about the dri-devel mailing list