[PATCH 1/8] drm: bridge: dw_hdmi: Call poweron/poweroff from atomic enable/disable
Daniel Vetter
daniel at ffwll.ch
Wed Jun 26 07:38:59 UTC 2024
On Mon, Jun 24, 2024 at 02:19:36PM +0200, Jonas Karlman wrote:
> Hi Neil,
>
> On 2024-06-24 11:56, neil.armstrong at linaro.org wrote:
> > On 24/06/2024 11:41, Jonas Karlman wrote:
> >> Hi Neil,
> >>
> >> On 2024-06-24 11:23, Neil Armstrong wrote:
> >>> On 11/06/2024 17:50, Jonas Karlman wrote:
> >>>> Change to only call poweron/poweroff from atomic_enable/atomic_disable
> >>>> ops instead of trying to keep a bridge_is_on state and poweron/off in
> >>>> the hotplug irq handler.
> >>>>
> >>>> A benefit of this is that drm mode_config mutex is always held at
> >>>> poweron/off, something that may reduce the need for our own mutex.
> >>>>
> >>>> Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
> >>>> ---
> >>>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 33 ++---------------------
> >>>> 1 file changed, 2 insertions(+), 31 deletions(-)
> >>>>
> >>>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> >>>> index 9f2bc932c371..34bc6f4754b8 100644
> >>>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> >>>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> >>>> @@ -172,7 +172,6 @@ struct dw_hdmi {
> >>>> enum drm_connector_force force; /* mutex-protected force state */
> >>>> struct drm_connector *curr_conn;/* current connector (only valid when !disabled) */
> >>>> bool disabled; /* DRM has disabled our bridge */
> >>>> - bool bridge_is_on; /* indicates the bridge is on */
> >>>> bool rxsense; /* rxsense state */
> >>>> u8 phy_mask; /* desired phy int mask settings */
> >>>> u8 mc_clkdis; /* clock disable register */
> >>>> @@ -2383,8 +2382,6 @@ static void initialize_hdmi_ih_mutes(struct dw_hdmi *hdmi)
> >>>>
> >>>> static void dw_hdmi_poweron(struct dw_hdmi *hdmi)
> >>>> {
> >>>> - hdmi->bridge_is_on = true;
> >>>> -
> >>>> /*
> >>>> * The curr_conn field is guaranteed to be valid here, as this function
> >>>> * is only be called when !hdmi->disabled.
> >>>> @@ -2398,30 +2395,6 @@ static void dw_hdmi_poweroff(struct dw_hdmi *hdmi)
> >>>> hdmi->phy.ops->disable(hdmi, hdmi->phy.data);
> >>>> hdmi->phy.enabled = false;
> >>>> }
> >>>> -
> >>>> - hdmi->bridge_is_on = false;
> >>>> -}
> >>>> -
> >>>> -static void dw_hdmi_update_power(struct dw_hdmi *hdmi)
> >>>> -{
> >>>> - int force = hdmi->force;
> >>>> -
> >>>> - if (hdmi->disabled) {
> >>>> - force = DRM_FORCE_OFF;
> >>>> - } else if (force == DRM_FORCE_UNSPECIFIED) {
> >>>> - if (hdmi->rxsense)
> >>>> - force = DRM_FORCE_ON;
> >>>> - else
> >>>> - force = DRM_FORCE_OFF;
> >>>> - }
> >>>
> >>> This means we always poweron the bridge even if rxsense is false ?
> >>
> >> If I follow the logic there should not be any difference, beside that
> >> power on now only happen in atomic_enable instead of sometime in irq
> >> handler.
> >>
> >> hdmi->rxsense is set to true based on hpd in dw_hdmi_setup_rx_sense().
> >> For both meson and dw-hdmi this means HPD=1 and not rxsense=1.
> >
> > Yeah I know, I was worried for other platforms using rxsense
>
> From what I can find only dw-hdmi.c and dw_hdmi_meson.c are caller of
> dw_hdmi_setup_rx_sense(). For meson the same value is passed for both
> hpd and rx_sense, everyone else hpd = HPD and rx_sense = RX_SENSE status.
>
> My understanding and testing based on Rockchip has shown that rx_sense
> has no significant impact before and after this change.
>
> >
> >>
> >> drm core will call the force/detect ops and enable/disable based on
> >> forced/HPD state, so I am not expecting any difference in how this
> >> currently works.
> >>
> >> This change to only poweron/setup in atomic_enable should also fix
> >> issues/situations where dw-hdmi was poweron too early during bootup in
> >> irq handler, before the drm driver was fully probed.
>
> I may have been wrong here, there is a check for disabled here so it
> should not have setup() before atomic_enable().
>
> Still we should ensure configure happen in atomic_enable(). The
> hpd_irq_event/hpd_notify calls will trigger a detect() and signal core
> if the bridge should be enabled/disabled when connector status changes.
>
> >
> > Hmm, but I thought the code wouldn't poweron the bridge is rxsense was 0
> > even if a mode was set, this won't work like this anymore right ?
>
> This is what I thought was happening, and the comment in code seem to
> indicate that. However, the code only seem to care about HPD=1 status to
> poweron() and possible both HPD=0 + RXSENSE=0 to poweroff().
More fundamental question: Why do we even care what happens in this case?
Userspace lit up an output that's not connected either
- it's broken, it gets to keep to pieces
- it knows what it's doing, there is a display, it's just broken, and it
_really_ wants the output to be lit up.
Drivers trying to be clever isn't a good idea here imo ...
-Sima
> To make matter more complex core also mainly care about detect() status
> and most/all related drivers seem to only use the the HPD status.
>
> So I would say that there should not be any changes in impact of the
> rxsense signal.
>
> Will also send a new patch in a v2 for dw_hdmi_irq() that may be related:
>
> - if (phy_stat & HDMI_PHY_HPD)
> + if ((intr_stat & HDMI_IH_PHY_STAT0_HPD) &&
> + (phy_stat & HDMI_PHY_HPD))
> status = connector_status_connected;
>
> or there may be a status_connected event triggered when rxsense goes
> from 1 to 0 and a second one with status_disconnected shortly after when
> hpd goes from 1 to 0 when the cable is removed.
>
> Regards,
> Jonas
>
> >
> > Neil
> >
> >>
> >> Regards,
> >> Jonas
> >>
> >>>
> >>> Neil
> >>>
> >>>> -
> >>>> - if (force == DRM_FORCE_OFF) {
> >>>> - if (hdmi->bridge_is_on)
> >>>> - dw_hdmi_poweroff(hdmi);
> >>>> - } else {
> >>>> - if (!hdmi->bridge_is_on)
> >>>> - dw_hdmi_poweron(hdmi);
> >>>> - }
> >>>> }
> >>>>
> >>>> /*
> >>>> @@ -2546,7 +2519,6 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
> >>>>
> >>>> mutex_lock(&hdmi->mutex);
> >>>> hdmi->force = connector->force;
> >>>> - dw_hdmi_update_power(hdmi);
> >>>> dw_hdmi_update_phy_mask(hdmi);
> >>>> mutex_unlock(&hdmi->mutex);
> >>>> }
> >>>> @@ -2955,7 +2927,7 @@ static void dw_hdmi_bridge_atomic_disable(struct drm_bridge *bridge,
> >>>> mutex_lock(&hdmi->mutex);
> >>>> hdmi->disabled = true;
> >>>> hdmi->curr_conn = NULL;
> >>>> - dw_hdmi_update_power(hdmi);
> >>>> + dw_hdmi_poweroff(hdmi);
> >>>> dw_hdmi_update_phy_mask(hdmi);
> >>>> handle_plugged_change(hdmi, false);
> >>>> mutex_unlock(&hdmi->mutex);
> >>>> @@ -2974,7 +2946,7 @@ static void dw_hdmi_bridge_atomic_enable(struct drm_bridge *bridge,
> >>>> mutex_lock(&hdmi->mutex);
> >>>> hdmi->disabled = false;
> >>>> hdmi->curr_conn = connector;
> >>>> - dw_hdmi_update_power(hdmi);
> >>>> + dw_hdmi_poweron(hdmi);
> >>>> dw_hdmi_update_phy_mask(hdmi);
> >>>> handle_plugged_change(hdmi, true);
> >>>> mutex_unlock(&hdmi->mutex);
> >>>> @@ -3073,7 +3045,6 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
> >>>> if (hpd)
> >>>> hdmi->rxsense = true;
> >>>>
> >>>> - dw_hdmi_update_power(hdmi);
> >>>> dw_hdmi_update_phy_mask(hdmi);
> >>>> }
> >>>> mutex_unlock(&hdmi->mutex);
> >>>
> >>
> >
>
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
More information about the dri-devel
mailing list