[PATCH v6 03/16] dt-bindings: mfd: mediatek: Add codec property for MT6357 PMIC

[Alexandre Mergnat]

On 25/06/2024 15:44, Krzysztof Kozlowski wrote:
> On 25/06/2024 11:23, Alexandre Mergnat wrote:
>>
>>
>> On 21/06/2024 17:00, Krzysztof Kozlowski wrote:
>>> On 19/06/2024 16:46, Alexandre Mergnat wrote:
>>>> Add the audio codec sub-device. This sub-device is used to set the
>>>> optional voltage values according to the hardware.
>>>> The properties are:
>>>>     - Setup of microphone bias voltage.
>>>>     - Setup of the speaker pin pull-down.
>>>>
>>>> Also, add the audio power supply property which is dedicated for
>>>> the audio codec sub-device.
>>>>
>>>> Signed-off-by: Alexandre Mergnat<amergnat at baylibre.com>
>>>> ---
>>>>    .../devicetree/bindings/mfd/mediatek,mt6357.yaml   | 33 ++++++++++++++++++++++
>>>>    1 file changed, 33 insertions(+)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml b/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
>>>> index 37423c2e0fdf..d95307393e75 100644
>>>> --- a/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
>>>> +++ b/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
>>>> @@ -37,6 +37,32 @@ properties:
>>>>      "#interrupt-cells":
>>>>        const: 2
>>>>    
>>>> +  vaud28-supply:
>>>> +    description: 2.8 volt supply phandle for the audio codec
>>>> +
>>>> +  audio-codec:
>>>> +    type: object
>>> Still not much improved. You do not have any resources there, so these
>>> should go to the parent node.
>>
>> Hi Krzysztof,
>>
>> vaud28-supply seems to be a mistake that I forward port.
>> In the V4, AFAII, your feedback [1] suggested me to move the vaud28-supply from the "audio-codec"
>> sub-node to the parent node, which for me is the "pmic" (mfd), because the property is considered as
>> power-supply.
>>
>>       pwrap {
>>           pmic {
>>               ...
>>               audio-codec {
>>                   ...
>>
>> Hardware side, vaud28-supply is the output of PMIC-regulator subsystem, and AVDD28 is the input of
>> PMIC-audio-codec subsystem. Then:
>> - The property name is wrong and must be change to AVDD28, which is a consumer (power input), not a
>> power-supply. => description: 2.8 volt power input for microphones (AU_VIN0, AU_VIN1, AU_VIN2)
>> - IMHO, move this property to the next parent (pwrap) isn't consistent. It should be moved back to
>> Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml (Done in the V4) into audio-codec
>> substystem, beside mediatek,micbias0-microvolt
> 
> I don't understand why do we talk again about supply. My comment was not
> under the supply.

Because your word are:
"
And now you should see how odd it looks. Supplies are part of entire
chip, not subblock, even if they supply dedicated domain within that chip.

That's why I asked to put it in the parent node.
"

My bad, I forgot to link you the old message in my previous answer [1]

[1] https://lore.kernel.org/all/6d21da37-8be7-467c-8878-d57af0b0201b@kernel.org/#t

-- 
Regards,
Alexandre