[PATCH] drm/bridge: adv7511: Exit interrupt handling when necessary
Adam Ford
aford173 at gmail.com
Tue May 21 21:49:12 UTC 2024
On Mon, May 20, 2024 at 4:16 PM Dmitry Baryshkov
<dmitry.baryshkov at linaro.org> wrote:
>
> On Mon, May 20, 2024 at 07:46:05AM -0500, Adam Ford wrote:
> > On Mon, May 20, 2024 at 7:00 AM Dmitry Baryshkov
> > <dmitry.baryshkov at linaro.org> wrote:
> > >
> > > On Mon, 20 May 2024 at 14:48, Sui Jingfeng <sui.jingfeng at linux.dev> wrote:
> > > >
> > > > Hi,
> > > >
> > > >
> > > > On 5/20/24 19:13, Dmitry Baryshkov wrote:
> > > > > On Mon, 20 May 2024 at 14:11, Sui Jingfeng <sui.jingfeng at linux.dev> wrote:
> > > > >>
> > > > >> Hi,
> > > > >>
> > > > >> On 5/20/24 06:11, Dmitry Baryshkov wrote:
> > > > >>> On Thu, May 16, 2024 at 06:10:06PM +0800, Liu Ying wrote:
> > > > >>>> Commit f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")
> > > > >>>> fails to consider the case where adv7511->i2c_main->irq is zero, i.e.,
> > > > >>>> no interrupt requested at all.
> > > > >>>>
> > > > >>>> Without interrupt, adv7511_wait_for_edid() could return -EIO sometimes,
> > > > >>>> because it polls adv7511->edid_read flag by calling adv7511_irq_process()
> > > > >>>> a few times, but adv7511_irq_process() happens to refuse to handle
> > > > >>>> interrupt by returning -ENODATA. Hence, EDID retrieval fails randomly.
> >
> > Sorry about that. I did some testing and didn't see any regressions,
> > but if it was random, it's likely I just was lucky to not see it.
> >
> > > > >>>>
> > > > >>>> Fix the issue by checking adv7511->i2c_main->irq before exiting interrupt
> > > > >>>> handling from adv7511_irq_process().
> > > > >>>>
> > > > >>>> Fixes: f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")
> > > > >>>> Signed-off-by: Liu Ying <victor.liu at nxp.com>
> > > > >>>> ---
> > > > >>>> drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 3 ++-
> > > > >>>> 1 file changed, 2 insertions(+), 1 deletion(-)
> > > > >>>>
> > > > >>>> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > > > >>>> index 6089b0bb9321..2074fa3c1b7b 100644
> > > > >>>> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > > > >>>> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > > > >>>> @@ -479,7 +479,8 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
> > > > >>>> return ret;
> > > > >>>>
> > > > >>>> /* If there is no IRQ to handle, exit indicating no IRQ data */
> > > > >>>> - if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
> > > > >>>> + if (adv7511->i2c_main->irq &&
> > > > >>>> + !(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
> > > > >>>> !(irq1 & ADV7511_INT1_DDC_ERROR))
> > > > >>>> return -ENODATA;
> > > > >>>
> > > > >>> I think it might be better to handle -ENODATA in adv7511_wait_for_edid()
> > > > >>> instead. WDYT?
> > > > >>>
> > > > >>
> > > > >> I think this is may deserve another patch.
> > > > >
> > > > > My point is that the IRQ handler is fine to remove -ENODATA here,
> > > >
> > > > [...]
> > > >
> > > > > there is no pending IRQ that can be handled.
> > > >
> > > > But there may has other things need to do in the adv7511_irq_process()
> > > > function.
> > >
> > > But the function returns anyway. So, we know that the condition is broken.
> >
> > When I originally submitted the patch, I only added the shared IRQ
> > flag without any IRQ condition checks, IRQ because I didn't want to
> > break anything. The feedback I got was to check to see if the IRQ was
> > intended by the device. My focus was the adv7511_drv.c file because
> > that appears to be what the registered IRQ hander was, but after
> > looking through adv7511_cec, I see that adv7511_cec_irq_process checks
> > adv_cec_tx_raw_status and returns if there is nothing to do.
> >
> > Would it make sense to move the if statement did the following things:
> >
> > - Make adv7511_cec_irq_process return an int and modify it to return
> > 0 in normal operation or return -ENODATA where there is nothing to do.
> > It already has the checks in place to determine if there is work to
> > do, so the impact here should be minimal.
> >
> > - Move the check I added on whether or not there is an interrupt to
> > the very end of adv7511_irq_process just before the return 0.
> >
> > - Instead of blindly returning 0, modify the if statement to read the
> > state of the return code of adv7511_cec_irq_process and the IRQ flags
> > it already checks. If ADV7511_INT0_HPD, ADV7511_INT0_EDID_READY and
> > ADV7511_INT1_DDC_ERROR are all not true and adv7511_cec_irq_process
> > returned early, return ENODATA, but if any of the interrupts was
> > present and adv7511_cec_irq_process did work, it would return 0.
> >
> > I think that would cover the situation where adv7511_cec_irq_process
> > would get called, and also prevent a false return of the IRQ being
> > handled when this part didn't handle anything.
> >
> > It would look something like:
> >
> > cec_irq = adv7511_cec_irq_process(adv7511, irq1);
> >
> > /* If there is no IRQ to handle, exit indicating no IRQ data */)
> > if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
> > !(irq1 & ADV7511_INT1_DDC_ERROR) &&
> > cec_irq == -ENODATA)
> > return -ENODATA;
> > else
> > return 0
> >
> >
> > OR...
> >
> >
> > Another alternative to all this is to modify the check that I added to
> > verify all the following flags which are currently checked in
> > adv7511_cec_irq_process :
> >
> > ADV7511_INT1_CEC_TX_READY
> > ADV7511_INT1_CEC_TX_ARBIT_LOST
> > ADV7511_INT1_CEC_TX_RETRY_TIMEOUT
> > ADV7511_INT1_CEC_RX_READY1
> > ADV7511_INT1_CEC_RX_READY2
> > ADV7511_INT1_CEC_RX_READY3
> >
> > It would look something like:
> >
> > /* If there is no IRQ to handle, exit indicating no IRQ data */
> > if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
> > !(irq1 & ADV7511_INT1_DDC_ERROR) &&
> > !(irq1 & ADV7511_INT1_CEC_TX_READY) &&
> > !(irq1 & ADV7511_INT1_CEC_TX_ARBIT_LOST) &&
> > !(irq1 & ADV7511_INT1_CEC_TX_RETRY_TIMEOUT) &&
> > !(irq1 & ADV7511_INT1_CEC_RX_READY1) &&
> > !(irq1 & ADV7511_INT1_CEC_RX_READY2) &&
> > !(irq1 & ADV7511_INT1_CEC_RX_READY3))
> > return -ENODATA;
>
> This definitely looks ugly. At least it should be a mask.
>
> I have a slightly different solution:
>
> Make adv7511_irq_process return <0 for error, IRQ_NONE or IRQ_HANDLED.
> This would also require tracking whether HPD, EDID or CEC processing
> actually took place (add temp var for the current 'handled' status, make
> adv7511_cec_irq_process() return IRQ_HANDLED too).
Dmitry,
I think I have addressed your concerns. I got feedback from a build
bot with one warning, so I'll address that, but i wasn't sure if I
should wait for feedback from you. I am traveling Friday-Tuesday, so
I was hoping to send a V2 on Thursday if there are no other concerns.
Liu,
I realized that I didn't properly copy-paste your e-mail address, so
you didn't get copied on the submission I just did. I'll reply to the
thread where I posted a bug fix with your proper e-mail address. If
you can try it to see if it addresses your issue, that would be really
helpful.
thanks,
adam
>
> >
> >
> > Please let me know what is preferred or if there is a third possible solution.
> >
> > I can write up a patch with a fixes tag later today when I get back to
> > my build machine.
> >
> > adam
> > >
> > > >
> > > > > So instead of continuing
> > > > > the execution when we know that IRQ bits are not set,
> > > >
> > > > Even when IRQ bits are not set, it just means that there is no HPD
> > > > and no EDID ready-to-read signal. HDMI CEC interrupts still need
> > > > to process.
> > >
> > > Yes. Let's get the CEC fixed. Then maybe we won't need this commit at all.
> > >
> > > >
> > > >
> > > > > it's better to
> > > > > ignore -ENODATA in the calling code and go on with msleep().
> > > > >
> > > >
> > > > So, It's confusing to ignore the -ENODATA here.
> > >
> > > [BTW: you had quotation levels wrong in two places, I've fixed them]
> > >
> > > --
> > > With best wishes
> > > Dmitry
>
> --
> With best wishes
> Dmitry
More information about the dri-devel
mailing list