[PATCH 2/2] drm: panel: nv3052c: Add WL-355608-A8 panel
John Watts
contact at jookia.org
Mon May 27 22:16:57 UTC 2024
Hi,
On Fri, May 24, 2024 at 10:33:14PM +1200, Ryan Walklin wrote:
> The WL-355608-A8 is a 3.5" 640x480 at 60Hz RGB LCD display from an unknown
> OEM, used in a number of handheld gaming devices made by Anbernic.
>
> Limited information is available online however the panel timing values
> (below) have been obtained from the vendor BSP. The panel appears to
> integrate a NV3052C LCD driver (or clone). Available devices address it
> in SPI/RGB mode, with the timing signals generated from the device
> SoC (in testing hardware an Allwinner H700) and passed through.
>
> Add a panel definition and display mode to the existing NV3502C driver.
>
> It was assumed during bringup that the initialisation sequence was the
> same as the existing Fascontek FS035VG158 panel, proved working during
> experimentation. However subsequent dumping of the init sequence with a
> logic analyser confirms one small change to VCOM_ADJ3 from 0x4a to 0x44,
> therefore a separate set of registers is also added.
>
> Timings:
> | Active | FP | Sync | BP | Total
> -----------|--------|------|------|------|-------
> Horizontal | 640 | 64 | 20 | 46 | 770
> Vertical | 480 | 21 | 4 | 15 | 520
>
> Signed-off-by: Ryan Walklin <ryan at testtoast.com>
> Co-developed-by: Hironori KIKUCHI <kikuchan98 at gmail.com>
> ---
> .../gpu/drm/panel/panel-newvision-nv3052c.c | 225 ++++++++++++++++++
> 1 file changed, 225 insertions(+)
>
> diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> index 1aab0c9ae..5de36ecec 100644
> --- a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> +++ b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> @@ -433,6 +433,202 @@ static const struct nv3052c_reg fs035vg158_panel_regs[] = {
> { 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
> };
>
> +
> +static const struct nv3052c_reg wl_355608_a8_panel_regs[] = {
> + // EXTC Command set enable, select page 1
> + { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x01 },
> + // Mostly unknown registers
> + { 0xe3, 0x00 },
> + { 0x40, 0x00 },
> + { 0x03, 0x40 },
> + { 0x04, 0x00 },
> + { 0x05, 0x03 },
> + { 0x08, 0x00 },
> + { 0x09, 0x07 },
> + { 0x0a, 0x01 },
> + { 0x0b, 0x32 },
> + { 0x0c, 0x32 },
> + { 0x0d, 0x0b },
> + { 0x0e, 0x00 },
> + { 0x23, 0xa0 },
> + { 0x24, 0x0c },
> + { 0x25, 0x06 },
> + { 0x26, 0x14 },
> + { 0x27, 0x14 },
> + { 0x38, 0xcc }, // VCOM_ADJ1
> + { 0x39, 0xd7 }, // VCOM_ADJ2
> + { 0x3a, 0x44 }, // VCOM_ADJ3
> + { 0x28, 0x40 },
> + { 0x29, 0x01 },
> + { 0x2a, 0xdf },
> + { 0x49, 0x3c },
> + { 0x91, 0x77 }, // EXTPW_CTRL2
> + { 0x92, 0x77 }, // EXTPW_CTRL3
> + { 0xa0, 0x55 },
> + { 0xa1, 0x50 },
> + { 0xa4, 0x9c },
> + { 0xa7, 0x02 },
> + { 0xa8, 0x01 },
> + { 0xa9, 0x01 },
> + { 0xaa, 0xfc },
> + { 0xab, 0x28 },
> + { 0xac, 0x06 },
> + { 0xad, 0x06 },
> + { 0xae, 0x06 },
> + { 0xaf, 0x03 },
> + { 0xb0, 0x08 },
> + { 0xb1, 0x26 },
> + { 0xb2, 0x28 },
> + { 0xb3, 0x28 },
> + { 0xb4, 0x33 },
> + { 0xb5, 0x08 },
> + { 0xb6, 0x26 },
> + { 0xb7, 0x08 },
> + { 0xb8, 0x26 },
> + { 0xf0, 0x00 },
> + { 0xf6, 0xc0 },
> + // EXTC Command set enable, select page 2
> + { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
> + // Set gray scale voltage to adjust gamma
> + { 0xb0, 0x0b }, // PGAMVR0
> + { 0xb1, 0x16 }, // PGAMVR1
> + { 0xb2, 0x17 }, // PGAMVR2
> + { 0xb3, 0x2c }, // PGAMVR3
> + { 0xb4, 0x32 }, // PGAMVR4
> + { 0xb5, 0x3b }, // PGAMVR5
> + { 0xb6, 0x29 }, // PGAMPR0
> + { 0xb7, 0x40 }, // PGAMPR1
> + { 0xb8, 0x0d }, // PGAMPK0
> + { 0xb9, 0x05 }, // PGAMPK1
> + { 0xba, 0x12 }, // PGAMPK2
> + { 0xbb, 0x10 }, // PGAMPK3
> + { 0xbc, 0x12 }, // PGAMPK4
> + { 0xbd, 0x15 }, // PGAMPK5
> + { 0xbe, 0x19 }, // PGAMPK6
> + { 0xbf, 0x0e }, // PGAMPK7
> + { 0xc0, 0x16 }, // PGAMPK8
> + { 0xc1, 0x0a }, // PGAMPK9
> + // Set gray scale voltage to adjust gamma
> + { 0xd0, 0x0c }, // NGAMVR0
> + { 0xd1, 0x17 }, // NGAMVR0
> + { 0xd2, 0x14 }, // NGAMVR1
> + { 0xd3, 0x2e }, // NGAMVR2
> + { 0xd4, 0x32 }, // NGAMVR3
> + { 0xd5, 0x3c }, // NGAMVR4
> + { 0xd6, 0x22 }, // NGAMPR0
> + { 0xd7, 0x3d }, // NGAMPR1
> + { 0xd8, 0x0d }, // NGAMPK0
> + { 0xd9, 0x07 }, // NGAMPK1
> + { 0xda, 0x13 }, // NGAMPK2
> + { 0xdb, 0x13 }, // NGAMPK3
> + { 0xdc, 0x11 }, // NGAMPK4
> + { 0xdd, 0x15 }, // NGAMPK5
> + { 0xde, 0x19 }, // NGAMPK6
> + { 0xdf, 0x10 }, // NGAMPK7
> + { 0xe0, 0x17 }, // NGAMPK8
> + { 0xe1, 0x0a }, // NGAMPK9
> + // EXTC Command set enable, select page 3
> + { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x03 },
> + // Set various timing settings
> + { 0x00, 0x2a }, // GIP_VST_1
> + { 0x01, 0x2a }, // GIP_VST_2
> + { 0x02, 0x2a }, // GIP_VST_3
> + { 0x03, 0x2a }, // GIP_VST_4
> + { 0x04, 0x61 }, // GIP_VST_5
> + { 0x05, 0x80 }, // GIP_VST_6
> + { 0x06, 0xc7 }, // GIP_VST_7
> + { 0x07, 0x01 }, // GIP_VST_8
> + { 0x08, 0x03 }, // GIP_VST_9
> + { 0x09, 0x04 }, // GIP_VST_10
> + { 0x70, 0x22 }, // GIP_ECLK1
> + { 0x71, 0x80 }, // GIP_ECLK2
> + { 0x30, 0x2a }, // GIP_CLK_1
> + { 0x31, 0x2a }, // GIP_CLK_2
> + { 0x32, 0x2a }, // GIP_CLK_3
> + { 0x33, 0x2a }, // GIP_CLK_4
> + { 0x34, 0x61 }, // GIP_CLK_5
> + { 0x35, 0xc5 }, // GIP_CLK_6
> + { 0x36, 0x80 }, // GIP_CLK_7
> + { 0x37, 0x23 }, // GIP_CLK_8
> + { 0x40, 0x03 }, // GIP_CLKA_1
> + { 0x41, 0x04 }, // GIP_CLKA_2
> + { 0x42, 0x05 }, // GIP_CLKA_3
> + { 0x43, 0x06 }, // GIP_CLKA_4
> + { 0x44, 0x11 }, // GIP_CLKA_5
> + { 0x45, 0xe8 }, // GIP_CLKA_6
> + { 0x46, 0xe9 }, // GIP_CLKA_7
> + { 0x47, 0x11 }, // GIP_CLKA_8
> + { 0x48, 0xea }, // GIP_CLKA_9
> + { 0x49, 0xeb }, // GIP_CLKA_10
> + { 0x50, 0x07 }, // GIP_CLKB_1
> + { 0x51, 0x08 }, // GIP_CLKB_2
> + { 0x52, 0x09 }, // GIP_CLKB_3
> + { 0x53, 0x0a }, // GIP_CLKB_4
> + { 0x54, 0x11 }, // GIP_CLKB_5
> + { 0x55, 0xec }, // GIP_CLKB_6
> + { 0x56, 0xed }, // GIP_CLKB_7
> + { 0x57, 0x11 }, // GIP_CLKB_8
> + { 0x58, 0xef }, // GIP_CLKB_9
> + { 0x59, 0xf0 }, // GIP_CLKB_10
> + // Map internal GOA signals to GOA output pad
> + { 0xb1, 0x01 }, // PANELD2U2
> + { 0xb4, 0x15 }, // PANELD2U5
> + { 0xb5, 0x16 }, // PANELD2U6
> + { 0xb6, 0x09 }, // PANELD2U7
> + { 0xb7, 0x0f }, // PANELD2U8
> + { 0xb8, 0x0d }, // PANELD2U9
> + { 0xb9, 0x0b }, // PANELD2U10
> + { 0xba, 0x00 }, // PANELD2U11
> + { 0xc7, 0x02 }, // PANELD2U24
> + { 0xca, 0x17 }, // PANELD2U27
> + { 0xcb, 0x18 }, // PANELD2U28
> + { 0xcc, 0x0a }, // PANELD2U29
> + { 0xcd, 0x10 }, // PANELD2U30
> + { 0xce, 0x0e }, // PANELD2U31
> + { 0xcf, 0x0c }, // PANELD2U32
> + { 0xd0, 0x00 }, // PANELD2U33
> + // Map internal GOA signals to GOA output pad
> + { 0x81, 0x00 }, // PANELU2D2
> + { 0x84, 0x15 }, // PANELU2D5
> + { 0x85, 0x16 }, // PANELU2D6
> + { 0x86, 0x10 }, // PANELU2D7
> + { 0x87, 0x0a }, // PANELU2D8
> + { 0x88, 0x0c }, // PANELU2D9
> + { 0x89, 0x0e }, // PANELU2D10
> + { 0x8a, 0x02 }, // PANELU2D11
> + { 0x97, 0x00 }, // PANELU2D24
> + { 0x9a, 0x17 }, // PANELU2D27
> + { 0x9b, 0x18 }, // PANELU2D28
> + { 0x9c, 0x0f }, // PANELU2D29
> + { 0x9d, 0x09 }, // PANELU2D30
> + { 0x9e, 0x0b }, // PANELU2D31
> + { 0x9f, 0x0d }, // PANELU2D32
> + { 0xa0, 0x01 }, // PANELU2D33
> + // EXTC Command set enable, select page 2
> + { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
> + // Unknown registers
> + { 0x01, 0x01 },
> + { 0x02, 0xda },
> + { 0x03, 0xba },
> + { 0x04, 0xa8 },
> + { 0x05, 0x9a },
> + { 0x06, 0x70 },
> + { 0x07, 0xff },
> + { 0x08, 0x91 },
> + { 0x09, 0x90 },
> + { 0x0a, 0xff },
> + { 0x0b, 0x8f },
> + { 0x0c, 0x60 },
> + { 0x0d, 0x58 },
> + { 0x0e, 0x48 },
> + { 0x0f, 0x38 },
> + { 0x10, 0x2b },
> + // EXTC Command set enable, select page 0
> + { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x00 },
> + // Display Access Control
> + { 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
> +};
> +
> static inline struct nv3052c *to_nv3052c(struct drm_panel *panel)
> {
> return container_of(panel, struct nv3052c, panel);
> @@ -670,6 +866,21 @@ static const struct drm_display_mode fs035vg158_modes[] = {
> },
> };
>
> +static const struct drm_display_mode wl_355608_a8_mode[] = {
> + {
> + .clock = 24000,
> + .hdisplay = 640,
> + .hsync_start = 640 + 64,
> + .hsync_end = 640 + 64 + 20,
> + .htotal = 640 + 64 + 20 + 46,
> + .vdisplay = 480,
> + .vsync_start = 480 + 21,
> + .vsync_end = 480 + 21 + 4,
> + .vtotal = 480 + 21 + 4 + 15,
> + .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> + },
> +};
> +
> static const struct nv3052c_panel_info ltk035c5444t_panel_info = {
> .display_modes = ltk035c5444t_modes,
> .num_modes = ARRAY_SIZE(ltk035c5444t_modes),
> @@ -692,9 +903,21 @@ static const struct nv3052c_panel_info fs035vg158_panel_info = {
> .panel_regs_len = ARRAY_SIZE(fs035vg158_panel_regs),
> };
>
> +static const struct nv3052c_panel_info wl_355608_a8_panel_info = {
> + .display_modes = wl_355608_a8_mode,
> + .num_modes = ARRAY_SIZE(wl_355608_a8_mode),
> + .width_mm = 150,
> + .height_mm = 94,
> + .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> + .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
> + .panel_regs = wl_355608_a8_panel_regs,
> + .panel_regs_len = ARRAY_SIZE(wl_355608_a8_panel_regs),
> +};
> +
> static const struct spi_device_id nv3052c_ids[] = {
> { "ltk035c5444t", },
> { "fs035vg158", },
> + { "wl_355608_a8", },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(spi, nv3052c_ids);
> @@ -702,6 +925,7 @@ MODULE_DEVICE_TABLE(spi, nv3052c_ids);
> static const struct of_device_id nv3052c_of_match[] = {
> { .compatible = "leadtek,ltk035c5444t", .data = <k035c5444t_panel_info },
> { .compatible = "fascontek,fs035vg158", .data = &fs035vg158_panel_info },
> + { .compatible = "wl_355608_a8", .data = &wl_355608_a8_panel_info },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, nv3052c_of_match);
> @@ -719,4 +943,5 @@ module_spi_driver(nv3052c_driver);
>
> MODULE_AUTHOR("Paul Cercueil <paul at crapouillou.net>");
> MODULE_AUTHOR("Christophe Branchereau <cbranchereau at gmail.com>");
> +MODULE_AUTHOR("Ryan Walklin <ryan at testtoast.com");
> MODULE_LICENSE("GPL v2");
> --
> 2.45.1
>
This all looks good to me, though I understand you may need to change the
compatible. Please CC me if this happens so I can re-review.
Reviewed-by: John Watts <contact at jookia.org>
John.
More information about the dri-devel
mailing list