[PATCH v3 10/10] ARM: dts: ti: omap: samsung-espresso10: Add initial support for Galaxy Tab 2 10.1

[Andreas Kemnade]

Am Fri,  8 Nov 2024 20:04:39 +0000
schrieb Mithil Bavishi <bavishimithil at gmail.com>:

> Create a device tree for the 10 inch variants (P5100, P5110, P5113)
> 
> Signed-off-by: Mithil Bavishi <bavishimithil at gmail.com>
> ---
>  .../dts/ti/omap/omap4-samsung-espresso10.dts  | 102 ++++++++++++++++++
>  1 file changed, 102 insertions(+)
>  create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
> 
> diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
> new file mode 100644
> index 000000000..70bbef468
> --- /dev/null
> +++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
> @@ -0,0 +1,102 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/dts-v1/;
> +
> +#include "omap4-samsung-espresso-common.dtsi"
> +#include <dt-bindings/power/summit,smb347-charger.h>
> +/ {
> +	model = "Samsung Galaxy Tab 2 (10 inch)";
> +	compatible = "samsung,espresso10", "ti,omap4430", "ti,omap4";
> +
> +	i2c-gpio-5 {
> +		smb347: charger at 6 {
> +			compatible = "summit,smb347";
> +			reg = <0x6>; // 0x0C >> 1
> +			interrupt-parent = <&gpio2>;
> +			interrupts = <0 IRQ_TYPE_EDGE_BOTH>;
> +
> +			summit,enable-usb-charging;
> +			summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
> +			summit,chip-temperature-threshold-celsius = <120>;
> +			summit,usb-current-limit-microamp = <1800000>;
> +		};
> +	};
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&backlight_pins>;
> +		pwms = <&pwm10 0 1600 0>;
> +		power-supply = <&reg_lcd>;
> +		enable-gpios = <&gpio3 31 GPIO_ACTIVE_HIGH>;
> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> +		default-brightness-level = <7>;
> +	};
> +
> +	panel {
> +		compatible = "samsung,ltn101al03", "panel-lvds";
> +		power-supply = <&reg_lcd>;
> +		width-mm = <223>;
> +		height-mm = <125>;
> +		data-mapping = "vesa-24";
> +		backlight = <&backlight>;
> +
> +		panel-timing {
> +			clock-frequency = <69818000>;
> +
> +			hback-porch = <64>;
> +			hactive = <1280>;
> +			hfront-porch = <16>;
> +			hsync-len = <48>;
> +
> +			vback-porch = <11>;
> +			vactive = <800>;
> +			vfront-porch = <16>;
> +			vsync-len = <3>;
> +
> +			hsync-active = <0>;
> +			vsync-active = <0>;
> +			de-active = <1>;
> +			pixelclk-active = <1>;
> +		};
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&bridge_out>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c3 {
> +	touchscreen: synaptics-rmi4-i2c at 20 {

touchscreen at 20

> +		compatible = "syna,rmi4-i2c";
> +		reg = <0x20>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		interrupt-parent = <&gpio2>;
> +		interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&touch_pins>;
> +
> +		avdd-supply = <&reg_touch_ldo_en>;
not known in schema

> +		vdd-supply = <&ldo6>;
> +
> +		syna,reset-delay-ms = <200>;
> +		syna,startup-delay-ms = <200>;
> +
> +		touchscreen-size-x = <1279>;

Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml:
horizontal resolution of touchscreen (maximum x coordinate reported + 1)

So this touchscreen reports max 1278?

> +		touchscreen-size-y = <799>;

same question.

And these things belong below rm4-f11 according to
Documentation/devicetree/bindings/input/syna,rmi4.yaml

Regards,
Andreas