[PATCH v4 2/3] dt-bindings: display: ti: Add schema for AM625 OLDI Transmitter
Aradhya Bhatia
aradhya.bhatia at linux.dev
Sun Nov 24 14:36:48 UTC 2024
From: Aradhya Bhatia <a-bhatia1 at ti.com>
The OLDI transmitters (TXes) do not have registers of their own, and are
dependent on the source video-ports (VPs) from the DSS to provide
configuration data. This hardware doesn't directly sit on the internal
bus of the SoC, but does so via the DSS. Hence, the OLDI TXes are
supposed to be child nodes under the DSS, and not independent devices.
Two of the OLDI TXes can function in tandem to output dual-link OLDI
output, or cloned single-link outputs. In these cases, one OLDI will be
the primary OLDI, and the other one, a companion. The following diagram
represents such a configuration.
+-----+-----+ +-------+
| | | | |
| | VP1 +----+--->+ OLDI0 | (Primary - may need companion)
| | | | | |
| DSS +-----+ | +-------+
| | | |
| | VP2 | | +-------+
| | | | | |
+-----+-----+ +--->+ OLDI1 | (Companion OLDI)
| |
+-------+
The DSS in AM625 SoC has a configuration like the one above. The AM625
DSS VP1 (port at 0) can connect and control 2 OLDI TXes, to use them in
dual-link or cloned single-link OLDI modes. It is only the VP1 that can
connect to either OLDI TXes for the AM625 DSS, and not the VP2.
Alternatively, on some future TI SoCs, along with the above
configuration, the OLDI TX can _also_ connect to separate video sources,
making them work entirely independent of each other. In this case,
neither of the OLDIs are "companion" or "secondary" OLDIs, and nor do
they require one. They both are independent and primary OLDIs. The
following diagram represents such a configuration.
+-----+-----+ +-------+
| | | | |
| | VP1 +--+----------->+ OLDI0 | (Primary - may need companion)
| | | | | |
| +-----+ | +-------+
| | | |
| | VP2 | |
| | | |
| DSS +-----+ | +---+ +-------+
| | | +-->+ M | | |
| | VP3 +----->+ U +--->+ OLDI1 | (Companion or Primary)
| | | | X | | |
| +-----+ +---+ +-------+
| | |
| | VP4 |
| | |
+-----+-----+
Note that depending on the mux configuration, the OLDIs can either be
working together in tandem - sourced by VP1, OR, they could be working
independently sourced by VP1 and VP3 respectively.
The idea is to support all the configurations with this OLDI TX schema.
The OLDI functionality is further supported by a system-control module,
which contains a few registers to control OLDI IO power and other
electrical characteristics of the IO lanes.
Add devicetree binding schema for the OLDI TXes to support various
configurations, and extend their support to the AM625 DSS.
Signed-off-by: Aradhya Bhatia <a-bhatia1 at ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia at linux.dev>
---
.../bindings/display/ti/ti,am625-oldi.yaml | 119 ++++++++++++++
.../bindings/display/ti/ti,am65x-dss.yaml | 153 ++++++++++++++++++
MAINTAINERS | 1 +
3 files changed, 273 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/ti/ti,am625-oldi.yaml
diff --git a/Documentation/devicetree/bindings/display/ti/ti,am625-oldi.yaml b/Documentation/devicetree/bindings/display/ti/ti,am625-oldi.yaml
new file mode 100644
index 000000000000..51b24db04e89
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/ti/ti,am625-oldi.yaml
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/ti/ti,am625-oldi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments AM625 OLDI Transmitter
+
+maintainers:
+ - Tomi Valkeinen <tomi.valkeinen at ideasonboard.com>
+ - Aradhya Bhatia <aradhya.bhatia at linux.dev>
+
+description:
+ The AM625 TI Keystone OpenLDI transmitter (OLDI TX) supports serialized RGB
+ pixel data transmission between host and flat panel display over LVDS (Low
+ Voltage Differential Sampling) interface. The OLDI TX consists of 7-to-1 data
+ serializers, and 4-data and 1-clock LVDS outputs. It supports the LVDS output
+ formats "jeida-18", "jeida-24" and "vesa-18", and can accept 24-bit RGB or
+ padded and un-padded 18-bit RGB bus formats as input.
+
+properties:
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+ description: serial clock input for the OLDI transmitters
+
+ clock-names:
+ const: serial
+
+ ti,companion-oldi:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to companion OLDI transmitter. This property is mandatory for the
+ primarty OLDI TX if the OLDI TXes are expected to work either in dual-lvds
+ mode or in clone mode. This property should point to the secondary OLDI
+ TX.
+
+ ti,secondary-oldi:
+ type: boolean
+ description:
+ Boolean property to mark the OLDI transmitter as the secondary one, when the
+ OLDI hardware is expected to run as a companion HW, in cases of dual-lvds
+ mode or clone mode. The primary OLDI hardware is responsible for all the
+ hardware configuration.
+
+ ti,oldi-io-ctrl:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to syscon device node mapping OLDI IO_CTRL registers found in the
+ control MMR region. These registers are required to toggle the I/O lane
+ power, and control its electrical characteristics.
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port at 0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Parallel RGB input port
+
+ port at 1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: LVDS output port
+
+ required:
+ - port at 0
+ - port at 1
+
+allOf:
+ - if:
+ required:
+ - ti,secondary-oldi
+ then:
+ properties:
+ ti,companion-oldi: false
+
+required:
+ - reg
+ - clocks
+ - clock-names
+ - ti,oldi-io-ctrl
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+ oldi-transmitters {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ oldi: oldi at 0 {
+ reg = <0>;
+ clocks = <&k3_clks 186 0>;
+ clock-names = "serial";
+ ti,oldi-io-ctrl = <&dss_oldi_io_ctrl>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ oldi_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+ port at 1 {
+ reg = <1>;
+ oldi_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml b/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
index 399d68986326..eb6a65f9970d 100644
--- a/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
+++ b/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
@@ -91,6 +91,24 @@ properties:
For AM625 DSS, the internal DPI output port node from video
port 1.
For AM62A7 DSS, the port is tied off inside the SoC.
+ properties:
+ endpoint at 0:
+ $ref: /schemas/graph.yaml#/properties/endpoint
+ description:
+ For AM625 DSS, VP Connection to OLDI0.
+ For AM65X DSS, OLDI output from the SoC.
+
+ endpoint at 1:
+ $ref: /schemas/graph.yaml#/properties/endpoint
+ description:
+ For AM625 DSS, VP Connection to OLDI1.
+
+ anyOf:
+ - required:
+ - endpoint
+ - required:
+ - endpoint at 0
+ - endpoint at 1
port at 1:
$ref: /schemas/graph.yaml#/properties/port
@@ -112,6 +130,26 @@ properties:
Input memory (from main memory to dispc) bandwidth limit in
bytes per second
+ oldi-transmitters:
+ description:
+ Child node under the DSS, to describe all the OLDI transmitters connected
+ to the DSS videoports.
+ type: object
+ additionalProperties: false
+ properties:
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ patternProperties:
+ '^oldi@[0-1]$':
+ type: object
+ $ref: ti,am625-oldi.yaml#
+ unevaluatedProperties: false
+ description: OLDI transmitters connected to the DSS VPs
+
allOf:
- if:
properties:
@@ -123,6 +161,19 @@ allOf:
ports:
properties:
port at 0: false
+ oldi-transmitters: false
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: ti,am65x-dss
+ then:
+ properties:
+ oldi-transmitters: false
+ port at 0:
+ properties:
+ endpoint at 1: false
required:
- compatible
@@ -171,3 +222,105 @@ examples:
};
};
};
+
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ dss1: dss at 30200000 {
+ compatible = "ti,am625-dss";
+ reg = <0x00 0x30200000 0x00 0x1000>, /* common */
+ <0x00 0x30202000 0x00 0x1000>, /* vidl1 */
+ <0x00 0x30206000 0x00 0x1000>, /* vid */
+ <0x00 0x30207000 0x00 0x1000>, /* ovr1 */
+ <0x00 0x30208000 0x00 0x1000>, /* ovr2 */
+ <0x00 0x3020a000 0x00 0x1000>, /* vp1 */
+ <0x00 0x3020b000 0x00 0x1000>, /* vp2 */
+ <0x00 0x30201000 0x00 0x1000>; /* common1 */
+ reg-names = "common", "vidl1", "vid",
+ "ovr1", "ovr2", "vp1", "vp2", "common1";
+ power-domains = <&k3_pds 186 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 186 6>,
+ <&vp1_clock>,
+ <&k3_clks 186 2>;
+ clock-names = "fck", "vp1", "vp2";
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ oldi-transmitters {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ oldi0: oldi at 0 {
+ reg = <0>;
+ clocks = <&k3_clks 186 0>;
+ clock-names = "serial";
+ ti,companion-oldi = <&oldi1>;
+ ti,oldi-io-ctrl = <&dss_oldi_io_ctrl>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ oldi0_in: endpoint {
+ remote-endpoint = <&dpi0_out0>;
+ };
+ };
+ port at 1 {
+ reg = <1>;
+ oldi0_out: endpoint {
+ remote-endpoint = <&panel_in0>;
+ };
+ };
+ };
+ };
+ oldi1: oldi at 1 {
+ reg = <1>;
+ clocks = <&k3_clks 186 0>;
+ clock-names = "serial";
+ ti,secondary-oldi;
+ ti,oldi-io-ctrl = <&dss_oldi_io_ctrl>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ oldi1_in: endpoint {
+ remote-endpoint = <&dpi0_out1>;
+ };
+ };
+ port at 1 {
+ reg = <1>;
+ oldi1_out: endpoint {
+ remote-endpoint = <&panel_in1>;
+ };
+ };
+ };
+ };
+ };
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dpi0_out0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&oldi0_in>;
+ };
+ dpi0_out1: endpoint at 1 {
+ reg = <1>;
+ remote-endpoint = <&oldi1_in>;
+ };
+ };
+ port at 1 {
+ reg = <1>;
+ dpi1_out: endpoint {
+ remote-endpoint = <&hdmi_bridge>;
+ };
+ };
+ };
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 93415153247b..d47a56c4d276 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7817,6 +7817,7 @@ M: Tomi Valkeinen <tomi.valkeinen at ideasonboard.com>
L: dri-devel at lists.freedesktop.org
S: Maintained
T: git https://gitlab.freedesktop.org/drm/misc/kernel.git
+F: Documentation/devicetree/bindings/display/ti/ti,am625-oldi.yaml
F: Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
F: Documentation/devicetree/bindings/display/ti/ti,j721e-dss.yaml
F: Documentation/devicetree/bindings/display/ti/ti,k2g-dss.yaml
--
2.34.1
More information about the dri-devel
mailing list