[PATCH v3 3/4] optee: sync secure world ABI headers
Jens Wiklander
jens.wiklander at linaro.org
Thu Nov 28 15:09:03 UTC 2024
Update the header files describing the secure world ABI, both with and
without FF-A. The ABI is extended to deal with restricted memory, but as
usual backward compatible.
Signed-off-by: Jens Wiklander <jens.wiklander at linaro.org>
---
drivers/tee/optee/optee_ffa.h | 27 ++++++++++---
drivers/tee/optee/optee_msg.h | 65 ++++++++++++++++++++++++++++++--
drivers/tee/optee/optee_smc.h | 71 ++++++++++++++++++++++++++++++++++-
3 files changed, 154 insertions(+), 9 deletions(-)
diff --git a/drivers/tee/optee/optee_ffa.h b/drivers/tee/optee/optee_ffa.h
index 257735ae5b56..7bd037200343 100644
--- a/drivers/tee/optee/optee_ffa.h
+++ b/drivers/tee/optee/optee_ffa.h
@@ -81,7 +81,7 @@
* as the second MSG arg struct for
* OPTEE_FFA_YIELDING_CALL_WITH_ARG.
* Bit[31:8]: Reserved (MBZ)
- * w5: Bitfield of secure world capabilities OPTEE_FFA_SEC_CAP_* below,
+ * w5: Bitfield of OP-TEE capabilities OPTEE_FFA_SEC_CAP_*
* w6: The maximum secure world notification number
* w7: Not used (MBZ)
*/
@@ -94,6 +94,8 @@
#define OPTEE_FFA_SEC_CAP_ASYNC_NOTIF BIT(1)
/* OP-TEE supports probing for RPMB device if needed */
#define OPTEE_FFA_SEC_CAP_RPMB_PROBE BIT(2)
+/* OP-TEE supports Restricted Memory for secure data path */
+#define OPTEE_FFA_SEC_CAP_RSTMEM BIT(3)
#define OPTEE_FFA_EXCHANGE_CAPABILITIES OPTEE_FFA_BLOCKING_CALL(2)
@@ -108,7 +110,7 @@
*
* Return register usage:
* w3: Error code, 0 on success
- * w4-w7: Note used (MBZ)
+ * w4-w7: Not used (MBZ)
*/
#define OPTEE_FFA_UNREGISTER_SHM OPTEE_FFA_BLOCKING_CALL(3)
@@ -119,16 +121,31 @@
* Call register usage:
* w3: Service ID, OPTEE_FFA_ENABLE_ASYNC_NOTIF
* w4: Notification value to request bottom half processing, should be
- * less than OPTEE_FFA_MAX_ASYNC_NOTIF_VALUE.
+ * less than OPTEE_FFA_MAX_ASYNC_NOTIF_VALUE
* w5-w7: Not used (MBZ)
*
* Return register usage:
* w3: Error code, 0 on success
- * w4-w7: Note used (MBZ)
+ * w4-w7: Not used (MBZ)
*/
#define OPTEE_FFA_ENABLE_ASYNC_NOTIF OPTEE_FFA_BLOCKING_CALL(5)
-#define OPTEE_FFA_MAX_ASYNC_NOTIF_VALUE 64
+#define OPTEE_FFA_MAX_ASYNC_NOTIF_VALUE 64
+
+/*
+ * Release Restricted memory
+ *
+ * Call register usage:
+ * w3: Service ID, OPTEE_FFA_RECLAIM_RSTMEM
+ * w4: Shared memory handle, lower bits
+ * w5: Shared memory handle, higher bits
+ * w6-w7: Not used (MBZ)
+ *
+ * Return register usage:
+ * w3: Error code, 0 on success
+ * w4-w7: Note used (MBZ)
+ */
+#define OPTEE_FFA_RELEASE_RSTMEM OPTEE_FFA_BLOCKING_CALL(8)
/*
* Call with struct optee_msg_arg as argument in the supplied shared memory
diff --git a/drivers/tee/optee/optee_msg.h b/drivers/tee/optee/optee_msg.h
index e8840a82b983..1b558526e7d9 100644
--- a/drivers/tee/optee/optee_msg.h
+++ b/drivers/tee/optee/optee_msg.h
@@ -133,13 +133,13 @@ struct optee_msg_param_rmem {
};
/**
- * struct optee_msg_param_fmem - ffa memory reference parameter
+ * struct optee_msg_param_fmem - FF-A memory reference parameter
* @offs_lower: Lower bits of offset into shared memory reference
* @offs_upper: Upper bits of offset into shared memory reference
* @internal_offs: Internal offset into the first page of shared memory
* reference
* @size: Size of the buffer
- * @global_id: Global identifier of Shared memory
+ * @global_id: Global identifier of the shared memory
*/
struct optee_msg_param_fmem {
u32 offs_low;
@@ -165,7 +165,7 @@ struct optee_msg_param_value {
* @attr: attributes
* @tmem: parameter by temporary memory reference
* @rmem: parameter by registered memory reference
- * @fmem: parameter by ffa registered memory reference
+ * @fmem: parameter by FF-A registered memory reference
* @value: parameter by opaque value
* @octets: parameter by octet string
*
@@ -296,6 +296,18 @@ struct optee_msg_arg {
*/
#define OPTEE_MSG_FUNCID_GET_OS_REVISION 0x0001
+/*
+ * Values used in OPTEE_MSG_CMD_LEND_RSTMEM below
+ * OPTEE_MSG_RSTMEM_RESERVED Reserved
+ * OPTEE_MSG_RSTMEM_SECURE_VIDEO_PLAY Secure Video Playback
+ * OPTEE_MSG_RSTMEM_TRUSTED_UI Trused UI
+ * OPTEE_MSG_RSTMEM_SECURE_VIDEO_RECORD Secure Video Recording
+ */
+#define OPTEE_MSG_RSTMEM_RESERVED 0
+#define OPTEE_MSG_RSTMEM_SECURE_VIDEO_PLAY 1
+#define OPTEE_MSG_RSTMEM_TRUSTED_UI 2
+#define OPTEE_MSG_RSTMEM_SECURE_VIDEO_RECORD 3
+
/*
* Do a secure call with struct optee_msg_arg as argument
* The OPTEE_MSG_CMD_* below defines what goes in struct optee_msg_arg::cmd
@@ -337,6 +349,49 @@ struct optee_msg_arg {
* OPTEE_MSG_CMD_STOP_ASYNC_NOTIF informs secure world that from now is
* normal world unable to process asynchronous notifications. Typically
* used when the driver is shut down.
+ *
+ * OPTEE_MSG_CMD_LEND_RSTMEM lends restricted memory. The passed normal
+ * physical memory is restricted from normal world access. The memory
+ * should be unmapped prior to this call since it becomes inaccessible
+ * during the request.
+ * Parameters are passed as:
+ * [in] param[0].attr OPTEE_MSG_ATTR_TYPE_VALUE_INPUT
+ * [in] param[0].u.value.a OPTEE_MSG_RSTMEM_* defined above
+ * [in] param[1].attr OPTEE_MSG_ATTR_TYPE_TMEM_INPUT
+ * [in] param[1].u.tmem.buf_ptr physical address
+ * [in] param[1].u.tmem.size size
+ * [in] param[1].u.tmem.shm_ref holds restricted memory reference
+ *
+ * OPTEE_MSG_CMD_RECLAIM_RSTMEM reclaims a previously lent restricted
+ * memory reference. The physical memory is accessible by the normal world
+ * after this function has return and can be mapped again. The information
+ * is passed as:
+ * [in] param[0].attr OPTEE_MSG_ATTR_TYPE_VALUE_INPUT
+ * [in] param[0].u.value.a holds restricted memory cookie
+ *
+ * OPTEE_MSG_CMD_GET_RSTMEM_CONFIG get configuration for a specific
+ * restricted memory use case. Parameters are passed as:
+ * [in] param[0].attr OPTEE_MSG_ATTR_TYPE_VALUE_INOUT
+ * [in] param[0].value.a OPTEE_MSG_RSTMEM_*
+ * [in] param[1].attr OPTEE_MSG_ATTR_TYPE_{R,F}MEM_OUTPUT
+ * [in] param[1].u.{r,f}mem Buffer or NULL
+ * [in] param[1].u.{r,f}mem.size Provided size of buffer or 0 for query
+ * output for the restricted use case:
+ * [out] param[0].value.a Minimal size of SDP memory
+ * [out] param[0].value.b Required alignment of size and start of
+ * restricted memory
+ * [out] param[1].{r,f}mem.size Size of output data
+ * [out] param[1].{r,f}mem If non-NULL, contains an array of
+ * uint16_t holding endpoints that
+ * must be included when lending
+ * memory for this use case
+ *
+ * OPTEE_MSG_CMD_ASSIGN_RSTMEM assigns use-case to restricted memory
+ * previously lent using the FFA_LEND framework ABI. Parameters are passed
+ * as:
+ * [in] param[0].attr OPTEE_MSG_ATTR_TYPE_VALUE_INPUT
+ * [in] param[0].u.value.a holds restricted memory cookie
+ * [in] param[0].u.value.b OPTEE_MSG_RSTMEM_* defined above
*/
#define OPTEE_MSG_CMD_OPEN_SESSION 0
#define OPTEE_MSG_CMD_INVOKE_COMMAND 1
@@ -346,6 +401,10 @@ struct optee_msg_arg {
#define OPTEE_MSG_CMD_UNREGISTER_SHM 5
#define OPTEE_MSG_CMD_DO_BOTTOM_HALF 6
#define OPTEE_MSG_CMD_STOP_ASYNC_NOTIF 7
+#define OPTEE_MSG_CMD_LEND_RSTMEM 8
+#define OPTEE_MSG_CMD_RECLAIM_RSTMEM 9
+#define OPTEE_MSG_CMD_GET_RSTMEM_CONFIG 10
+#define OPTEE_MSG_CMD_ASSIGN_RSTMEM 11
#define OPTEE_MSG_FUNCID_CALL_WITH_ARG 0x0004
#endif /* _OPTEE_MSG_H */
diff --git a/drivers/tee/optee/optee_smc.h b/drivers/tee/optee/optee_smc.h
index 879426300821..abc379ce190c 100644
--- a/drivers/tee/optee/optee_smc.h
+++ b/drivers/tee/optee/optee_smc.h
@@ -264,7 +264,6 @@ struct optee_smc_get_shm_config_result {
#define OPTEE_SMC_SEC_CAP_HAVE_RESERVED_SHM BIT(0)
/* Secure world can communicate via previously unregistered shared memory */
#define OPTEE_SMC_SEC_CAP_UNREGISTERED_SHM BIT(1)
-
/*
* Secure world supports commands "register/unregister shared memory",
* secure world accepts command buffers located in any parts of non-secure RAM
@@ -280,6 +279,10 @@ struct optee_smc_get_shm_config_result {
#define OPTEE_SMC_SEC_CAP_RPC_ARG BIT(6)
/* Secure world supports probing for RPMB device if needed */
#define OPTEE_SMC_SEC_CAP_RPMB_PROBE BIT(7)
+/* Secure world supports Secure Data Path */
+#define OPTEE_SMC_SEC_CAP_SDP BIT(8)
+/* Secure world supports dynamic restricted memory */
+#define OPTEE_SMC_SEC_CAP_DYNAMIC_RSTMEM BIT(9)
#define OPTEE_SMC_FUNCID_EXCHANGE_CAPABILITIES 9
#define OPTEE_SMC_EXCHANGE_CAPABILITIES \
@@ -451,6 +454,72 @@ struct optee_smc_disable_shm_cache_result {
/* See OPTEE_SMC_CALL_WITH_REGD_ARG above */
#define OPTEE_SMC_FUNCID_CALL_WITH_REGD_ARG 19
+/*
+ * Get Secure Data Path memory config
+ *
+ * Returns the Secure Data Path memory config.
+ *
+ * Call register usage:
+ * a0 SMC Function ID, OPTEE_SMC_GET_SDP_CONFIG
+ * a2-6 Not used, must be zero
+ * a7 Hypervisor Client ID register
+ *
+ * Have config return register usage:
+ * a0 OPTEE_SMC_RETURN_OK
+ * a1 Physical address of start of SDP memory
+ * a2 Size of SDP memory
+ * a3 Not used
+ * a4-7 Preserved
+ *
+ * Not available register usage:
+ * a0 OPTEE_SMC_RETURN_ENOTAVAIL
+ * a1-3 Not used
+ * a4-7 Preserved
+ */
+#define OPTEE_SMC_FUNCID_GET_SDP_CONFIG 20
+#define OPTEE_SMC_GET_SDP_CONFIG \
+ OPTEE_SMC_FAST_CALL_VAL(OPTEE_SMC_FUNCID_GET_SDP_CONFIG)
+
+struct optee_smc_get_sdp_config_result {
+ unsigned long status;
+ unsigned long start;
+ unsigned long size;
+ unsigned long flags;
+};
+
+/*
+ * Get Secure Data Path dynamic memory config
+ *
+ * Returns the Secure Data Path dynamic memory config.
+ *
+ * Call register usage:
+ * a0 SMC Function ID, OPTEE_SMC_GET_DYN_SHM_CONFIG
+ * a2-6 Not used, must be zero
+ * a7 Hypervisor Client ID register
+ *
+ * Have config return register usage:
+ * a0 OPTEE_SMC_RETURN_OK
+ * a1 Minamal size of SDP memory
+ * a2 Required alignment of size and start of registered SDP memory
+ * a3 Not used
+ * a4-7 Preserved
+ *
+ * Not available register usage:
+ * a0 OPTEE_SMC_RETURN_ENOTAVAIL
+ * a1-3 Not used
+ * a4-7 Preserved
+ */
+
+#define OPTEE_SMC_FUNCID_GET_DYN_SDP_CONFIG 21
+#define OPTEE_SMC_GET_DYN_SDP_CONFIG \
+ OPTEE_SMC_FAST_CALL_VAL(OPTEE_SMC_FUNCID_GET_DYN_SDP_CONFIG)
+
+struct optee_smc_get_dyn_sdp_config_result {
+ unsigned long status;
+ unsigned long size;
+ unsigned long align;
+ unsigned long flags;
+};
/*
* Resume from RPC (for example after processing a foreign interrupt)
--
2.43.0
More information about the dri-devel
mailing list