[PATCH v2 6/9] drm/bridge: Add ITE IT6263 LVDS to HDMI converter

[Dmitry Baryshkov]

On Sat, Oct 12, 2024 at 03:35:40PM +0800, Liu Ying wrote:
> Add basic HDMI video output support. Currently, only RGB888 output
> pixel format is supported.  At the LVDS input side, the driver
> supports single LVDS link and dual LVDS links with "jeida-24" LVDS
> mapping.
> 
> Product link:
> https://www.ite.com.tw/en/product/cate1/IT6263
> 
> Signed-off-by: Liu Ying <victor.liu at nxp.com>
> ---
> v2:
> * Add AVI inforframe support.  (Maxime)
> * Add DRM_MODE_CONNECTOR_HDMIA.  (Biju)
> * Rename it6263_reset() to it6263_hw_reset().  (Biju)
> * Check number of LVDS link data lanes.  (Biju)
> 
>  drivers/gpu/drm/bridge/Kconfig      |   8 +
>  drivers/gpu/drm/bridge/Makefile     |   1 +
>  drivers/gpu/drm/bridge/ite-it6263.c | 919 ++++++++++++++++++++++++++++
>  3 files changed, 928 insertions(+)
>  create mode 100644 drivers/gpu/drm/bridge/ite-it6263.c
> 

[...]

> +static int it6263_parse_dt(struct it6263 *it)
> +{
> +	struct device *dev = it->dev;
> +	struct device_node *port0, *port1;
> +	int ret;
> +
> +	ret = of_property_read_u8(dev->of_node, "ite,lvds-link-num-data-lanes",
> +				  &it->lvds_link_num_dlanes);
> +	if (ret) {
> +		dev_err(dev, "failed to get LVDS link number of data lanes: %d\n",
> +			ret);
> +		return ret;
> +	}
> +
> +	it->next_bridge = devm_drm_of_get_bridge(dev, dev->of_node, 2, 0);
> +	if (IS_ERR(it->next_bridge))
> +		return dev_err_probe(dev, PTR_ERR(it->next_bridge),
> +				     "failed to get next bridge\n");
> +
> +	port0 = of_graph_get_port_by_id(dev->of_node, 0);
> +	port1 = of_graph_get_port_by_id(dev->of_node, 1);
> +	if (port0 && port1) {
> +		if (of_property_read_bool(port0, "dual-lvds-even-pixels") &&
> +		    of_property_read_bool(port1, "dual-lvds-odd-pixels")) {
> +			it->lvds_dual_link = true;
> +			it->lvds_link12_swap = true;
> +		} else if (of_property_read_bool(port0, "dual-lvds-odd-pixels") &&
> +			   of_property_read_bool(port1, "dual-lvds-even-pixels")) {
> +			it->lvds_dual_link = true;
> +		}
> +
> +		if (!it->lvds_dual_link) {
> +			dev_err(dev,
> +				"failed to get LVDS dual link pixel order\n");
> +			ret = -EINVAL;
> +		}

Please use drm_of_lvds_get_dual_link_pixel_order(), it validates that
the DT definition is sound: one port for odd pixels, one port for even
pixels.

> +	} else if (port1) {
> +		ret = -EINVAL;
> +		dev_err(dev, "single input LVDS port1 is not supported\n");
> +	} else if (!port0) {
> +		ret = -EINVAL;
> +		dev_err(dev, "no input LVDS port\n");
> +	}
> +
> +	of_node_put(port0);
> +	of_node_put(port1);
> +
> +	return ret;
> +}
> +

-- 
With best wishes
Dmitry