[PATCH v4 4/6] arm64: dts: qcom: Add initial support for MSM8937

[Konrad Dybcio]

On 3/15/25 3:57 PM, Barnabás Czémán wrote:
> From: Dang Huynh <danct12 at riseup.net>
> 
> Add initial support for MSM8937 SoC.
> 
> Signed-off-by: Dang Huynh <danct12 at riseup.net>
> Co-developed-by: Barnabás Czémán <barnabas.czeman at mainlining.org>
> Signed-off-by: Barnabás Czémán <barnabas.czeman at mainlining.org>
> ---

[...]

> +			power-domains = <&cpu_pd0>;
> +			power-domain-names = "psci";

So CPU4-7 get "nicer" idle, but 0-3 don't?

[...]

> +		cpu-map {
> +			/* The MSM8937 has 2 cluster A53 setup. */

This comment seems superfluous

[...]

> +	timer {

'p' < 't', please sort top-level nodes alphabetically

[...]

> +				wcss-wlan2-pins {
> +					pins = "gpio76";
> +					function = "wcss_wlan2";
> +					drive-strength = <6>;

please unify this order (drive-strength before bias)

> +					bias-pull-up;
> +
> +				};

Extra newline

[...]

> +		gpu: gpu at 1c00000 {
> +			compatible = "qcom,adreno-505.0", "qcom,adreno";
> +			reg = <0x1c00000 0x40000>;
> +			reg-names = "kgsl_3d0_reg_memory";
> +			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "kgsl_3d0_irq";
> +			#cooling-cells = <2>;
> +			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
> +				<&gcc GCC_OXILI_AHB_CLK>,
> +				<&gcc GCC_BIMC_GFX_CLK>,
> +				<&gcc GCC_BIMC_GPU_CLK>,
> +				<&gcc GCC_OXILI_TIMER_CLK>,
> +				<&gcc GCC_OXILI_AON_CLK>;

Please align the <s

> +			clock-names = "core",
> +				      "iface",
> +				      "mem_iface",
> +				      "alt_mem_iface",
> +				      "rbbmtimer",
> +				      "alwayson";
> +			operating-points-v2 = <&gpu_opp_table>;
> +			power-domains = <&gcc OXILI_GX_GDSC>;
> +
> +			iommus = <&adreno_smmu 0>;
> +
> +			status = "disabled";
> +
> +			gpu_opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				opp-19200000 {
> +					opp-hz = /bits/ 64 <19200000>;
> +					opp-supported-hw = <0xFF>;

0xff is overly broad, please document the existing known speed bins

[...]

> +		adreno_smmu: iommu at 1c40000 {
> +			compatible = "qcom,msm8996-smmu-v2",
> +				     "qcom,adreno-smmu",
> +				     "qcom,smmu-v2";
> +			reg = <0x1c40000 0x10000>;

Does it work as-is, without iommu changes?

[...]

> +	thermal_zones: thermal-zones {
> +		aoss-thermal {
> +			polling-delay-passive = <250>;

There are no passive trip points> +
> +			thermal-sensors = <&tsens 0>;
> +
> +			trips {
> +				aoss_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};

Please convert these to 'critical' instead

[...]

> +		cpuss1-thermal {
> +			polling-delay-passive = <250>;

You can drop polling-delay-passive under CPU tzones, as threshold
crossing is interrupt-driven

> +
> +			thermal-sensors = <&tsens 4>;
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpuss1_alert0>;
> +					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +
> +			trips {
> +				cpuss1_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpuss1_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};

On newer platforms we rely on LMH to shut down the device if it
were to reach the junction temperature, but let's leave them here
as probably no one remembers for sure how reliable that is on these
older platforms and you're most likely not willing to test that

Konrad