[PATCH v11 10/12] drm/msm/dpu: support SSPP assignment for quad-pipe case

[Dmitry Baryshkov]

On Tue, Jun 03, 2025 at 10:37:37PM +0800, Jun Nie wrote:
> Dmitry Baryshkov <dmitry.baryshkov at oss.qualcomm.com> 于2025年6月3日周二 18:21写道：
> >
> > On Tue, Jun 03, 2025 at 03:10:09PM +0800, Jun Nie wrote:
> > > Currently, SSPPs are assigned to a maximum of two pipes. However,
> > > quad-pipe usage scenarios require four pipes and involve configuring
> > > two stages. In quad-pipe case, the first two pipes share a set of
> > > mixer configurations and enable multi-rect mode when certain
> > > conditions are met. The same applies to the subsequent two pipes.
> > >
> > > Assign SSPPs to the pipes in each stage using a unified method and
> > > to loop the stages accordingly.
> > >
> > > Signed-off-by: Jun Nie <jun.nie at linaro.org>
> > > ---
> > >  drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 148 +++++++++++++++++++-----------
> > >  1 file changed, 94 insertions(+), 54 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> > > index 0bb153a71353ca9eaca138ebbee4cd699414771d..501b6a1bad4a1fee832f15efa7caec136a669da5 100644
> > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> > > @@ -961,6 +961,33 @@ static int dpu_plane_is_multirect_parallel_capable(struct dpu_hw_sspp *sspp,
> > >               dpu_plane_is_parallel_capable(pipe_cfg, fmt, max_linewidth);
> > >  }
> > >
> > > +static bool dpu_plane_get_single_pipe(struct dpu_plane_state *pstate,
> > > +                                   struct dpu_sw_pipe **single_pipe,
> > > +                                   struct dpu_sw_pipe_cfg **single_pipe_cfg,
> > > +                                   bool config_pipe)
> >
> > Could you please describe, what does this function do? Why is it
> > returning the pipe or configuring a pipe?
> 
> It search all pipes. If there is only one valid pipe, return it via
> pointer and function returns true.
> If the config_pipe flag is set, multirect_index and multirect_mode are
> also initialized. See below.

This doesn't look like a description of a single action. Please don't
try to mix different actions into a single function.

> >
> > > +{
> > > +     int i, valid_pipe = 0;
> > > +     struct dpu_sw_pipe *pipe;
> > > +
> > > +     for (i = 0; i < PIPES_PER_PLANE; i++) {
> > > +             if (drm_rect_width(&pstate->pipe_cfg[i].src_rect) != 0) {
> > > +                     valid_pipe++;
> > > +                     if (valid_pipe > 1)
> > > +                             return false;
> > > +                     *single_pipe = &pstate->pipe[i];
> > > +                     *single_pipe_cfg = &pstate->pipe_cfg[i];
> > > +             } else {
> > > +                     if (!config_pipe)
> > > +                             continue;
> > > +                     pipe = &pstate->pipe[i];
> > > +                     pipe->multirect_index = DPU_SSPP_RECT_SOLO;
> > > +                     pipe->multirect_mode = DPU_SSPP_MULTIRECT_NONE;
> > > +                     pipe->sspp = NULL;
> > > +             }
> > > +     }
> > > +
> > > +     return true;
> > > +}
> > >
> > >  static int dpu_plane_atomic_check_sspp(struct drm_plane *plane,
> > >                                      struct drm_atomic_state *state,

-- 
With best wishes
Dmitry