[PATCH v4 10/15] drm: renesas: rz-du: mipi_dsi: Use mHz for D-PHY frequency calculations
Biju Das
biju.das.jz at bp.renesas.com
Sun May 4 12:51:27 UTC 2025
Hi Prabhakar,
Thanks for the patch.
> -----Original Message-----
> From: Prabhakar <prabhakar.csengg at gmail.com>
> Sent: 30 April 2025 21:41
> Subject: [PATCH v4 10/15] drm: renesas: rz-du: mipi_dsi: Use mHz for D-PHY frequency calculations
>
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj at bp.renesas.com>
>
> Pass the HSFREQ in milli-Hz to the `dphy_init()` callback to improve precision, especially for the
> RZ/V2H(P) SoC, where PLL dividers require high accuracy.
>
> These changes prepare the driver for upcoming RZ/V2H(P) SoC support.
>
> Co-developed-by: Fabrizio Castro <fabrizio.castro.jz at renesas.com>
> Signed-off-by: Fabrizio Castro <fabrizio.castro.jz at renesas.com>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj at bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz at bp.renesas.com>
Cheers,
Biju
> ---
> v3->v4:
> - Used MILLI instead of KILO
> - Made use of mul_u32_u32() for multiplication
>
> v2->v3:
> - Replaced `unsigned long long` with `u64`
> - Replaced *_mhz with *_millihz` in functions
>
> v1->v2:
> - No changes
> ---
> ---
> drivers/gpu/drm/renesas/rz-du/rzg2l_mipi_dsi.c | 13 ++++++++-----
> 1 file changed, 8 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_mipi_dsi.c b/drivers/gpu/drm/renesas/rz-
> du/rzg2l_mipi_dsi.c
> index ed259627f5e8..a4c0dbae4a46 100644
> --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_mipi_dsi.c
> +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_mipi_dsi.c
> @@ -33,7 +33,7 @@
> struct rzg2l_mipi_dsi;
>
> struct rzg2l_mipi_dsi_hw_info {
> - int (*dphy_init)(struct rzg2l_mipi_dsi *dsi, unsigned long hsfreq);
> + int (*dphy_init)(struct rzg2l_mipi_dsi *dsi, u64 hsfreq_millihz);
> void (*dphy_exit)(struct rzg2l_mipi_dsi *dsi);
> u32 phy_reg_offset;
> u32 link_reg_offset;
> @@ -203,8 +203,9 @@ static u32 rzg2l_mipi_dsi_link_read(struct rzg2l_mipi_dsi *dsi, u32 reg)
> */
>
> static int rzg2l_mipi_dsi_dphy_init(struct rzg2l_mipi_dsi *dsi,
> - unsigned long hsfreq)
> + u64 hsfreq_millihz)
> {
> + unsigned long hsfreq = DIV_ROUND_CLOSEST_ULL(hsfreq_millihz, MILLI);
> const struct rzg2l_mipi_dsi_timings *dphy_timings;
> unsigned int i;
> u32 dphyctrl0;
> @@ -277,6 +278,7 @@ static int rzg2l_mipi_dsi_startup(struct rzg2l_mipi_dsi *dsi,
> const struct drm_display_mode *mode) {
> unsigned long hsfreq, vclk_rate;
> + u64 hsfreq_millihz;
> unsigned int bpp;
> u32 txsetr;
> u32 clstptsetr;
> @@ -305,9 +307,9 @@ static int rzg2l_mipi_dsi_startup(struct rzg2l_mipi_dsi *dsi,
> */
> bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> vclk_rate = clk_get_rate(dsi->vclk);
> - hsfreq = DIV_ROUND_CLOSEST_ULL(vclk_rate * bpp, dsi->lanes);
> + hsfreq_millihz = DIV_ROUND_CLOSEST_ULL(mul_u32_u32(vclk_rate, bpp *
> +MILLI), dsi->lanes);
>
> - ret = dsi->info->dphy_init(dsi, hsfreq);
> + ret = dsi->info->dphy_init(dsi, hsfreq_millihz);
> if (ret < 0)
> goto err_phy;
>
> @@ -315,6 +317,7 @@ static int rzg2l_mipi_dsi_startup(struct rzg2l_mipi_dsi *dsi,
> txsetr = TXSETR_DLEN | TXSETR_NUMLANEUSE(dsi->lanes - 1) | TXSETR_CLEN;
> rzg2l_mipi_dsi_link_write(dsi, TXSETR, txsetr);
>
> + hsfreq = DIV_ROUND_CLOSEST_ULL(hsfreq_millihz, MILLI);
> /*
> * Global timings characteristic depends on high speed Clock Frequency
> * Currently MIPI DSI-IF just supports maximum FHD at 60 with:
> @@ -778,7 +781,7 @@ static int rzg2l_mipi_dsi_probe(struct platform_device *pdev)
> * mode->clock and format are not available. So initialize DPHY with
> * timing parameters for 80Mbps.
> */
> - ret = dsi->info->dphy_init(dsi, 80000000);
> + ret = dsi->info->dphy_init(dsi, 80000000ULL * MILLI);
> if (ret < 0)
> goto err_phy;
>
> --
> 2.49.0
More information about the dri-devel
mailing list