[Freedreno] [PATCH v12 5/5] dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings

[spanda at codeaurora.org]

On 2018-07-05 15:48, Andrzej Hajda wrote:
> On 05.07.2018 08:38, spanda at codeaurora.org wrote:
>> On 2018-06-29 17:44, Andrzej Hajda wrote:
>>> On 21.06.2018 14:32, Sandeep Panda wrote:
>>>> Innolux TV123WAM is a 12.3" eDP display panel with
>>>> 2160x1440 resolution, which can be supported by simple
>>>> panel driver.
>>> Are you sure this is Innolux? Quick grep on Internet finds only BOE
>>> panel with this TV123WAM[1].
>>> 
>>> [1]:
>>> https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/138/TV123WAM_2D00_ND0_5F00_Product-spec_5F00_BOE_5F00_20161115_2D00_A00.pdf
>>> 
>> The panel used here is innolux, which is a 2k panel. Where the BOE one
>> is a 1080p panel.
> 
> My doubts comes from the fact that Innolux uses different convention 
> for
> panel naming, see for example [1].
> 
> According to this convention your panel should have name starting with:
> N123ZDG-
> 
> TV123WAM follows BOE's convention.
> 
> Do you have datasheet, physical panel or something to ensure the name 
> is
> correct?
> 
> [1]:
> http://www.panelook.com/bramodlist.php?st=&pl=&brands[]=63&signal_type_category=70
> 
> Regards
> Andrzej
> 
The data sheet i have does not mention any version info/id of innolux 
panel, so i took the
version name from a down stream patch we had earlier used to bring up 
this panel.
Unfortunately i can not share the data sheet also as it is water marked 
as confidential.

This panel patches are already merged in drm-misc, will upload a new 
patch to remove tv123* name
and put some generic innolux panel name like innolux,2k


>> 
>>> Regards
>>> Andrzej
>>>> Changes in v1:
>>>>  - Make use of simple panel driver instead of creating
>>>>    a new driver for this panel (Sean Paul).
>>>>  - Combine dt-binding and driver changes into one patch
>>>>    as done by other existing panel support changes.
>>>> 
>>>> Changes in v2:
>>>>  - Separate driver change from dt-binding documentation (Rob 
>>>> Herring).
>>>>  - Add the properties from simple-panel binding that are applicable 
>>>> to
>>>>    this panel (Rob Herring).
>>>> 
>>>> Signed-off-by: Sandeep Panda <spanda at codeaurora.org>
>>>> Reviewed-by: Rob Herring <robh at kernel.org>
>>>> ---
>>>>  .../bindings/display/panel/innolux,tv123wam.txt      | 20
>>>> ++++++++++++++++++++
>>>>  1 file changed, 20 insertions(+)
>>>>  create mode 100644
>>>> Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt
>>>> 
>>>> diff --git
>>>> a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt
>>>> b/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt
>>>> new file mode 100644
>>>> index 000000000000..a9b35265fa13
>>>> --- /dev/null
>>>> +++
>>>> b/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt
>>>> @@ -0,0 +1,20 @@
>>>> +Innolux TV123WAM 12.3 inch eDP 2K display panel
>>>> +
>>>> +This binding is compatible with the simple-panel binding, which is
>>>> specified
>>>> +in simple-panel.txt in this directory.
>>>> +
>>>> +Required properties:
>>>> +- compatible: should be "innolux,tv123wam"
>>>> +- power-supply: regulator to provide the supply voltage
>>>> +
>>>> +Optional properties:
>>>> +- enable-gpios: GPIO pin to enable or disable the panel
>>>> +- backlight: phandle of the backlight device attached to the panel
>>>> +
>>>> +Example:
>>>> +	panel_edp: panel-edp {
>>>> +		compatible = "innolux,tv123wam";
>>>> +		enable-gpios = <&msmgpio 31 GPIO_ACTIVE_LOW>;
>>>> +		power-supply = <&pm8916_l2>;
>>>> +		backlight = <&backlight>;
>>>> +	};
>> 
>>