[Freedreno] [PATCH v8 2/4] dt-bindings: drm/bridge: Document sn65dsi86 bridge bindings
spanda at codeaurora.org
spanda at codeaurora.org
Wed Jun 6 04:50:16 UTC 2018
On 2018-06-05 20:50, Rob Herring wrote:
> On Tue, Jun 05, 2018 at 11:10:16AM +0530, Sandeep Panda wrote:
>> Document the bindings used for the sn65dsi86 DSI to eDP bridge.
>>
>> Changes in v1:
>> - Rephrase the dt-binding descriptions to be more inline with
>> existing
>> bindings (Andrzej Hajda).
>> - Add missing dt-binding that are parsed by corresponding driver
>> (Andrzej Hajda).
>>
>> Changes in v2:
>> - Remove edp panel specific dt-binding entries. Only keep bridge
>> specific entries (Sean Paul).
>> - Remove custom-modes dt entry since its usage is removed from driver
>> also (Sean Paul).
>> - Remove is-pluggable dt entry since this will not be needed anymore
>> (Sean Paul).
>>
>> Changes in v3:
>> - Remove irq-gpio dt entry and instead populate is an interrupt
>> property (Rob Herring).
>>
>> Changes in v4:
>> - Add link to bridge chip datasheet (Stephen Boyd)
>> - Add vpll and vcc regulator supply bindings (Stephen Boyd)
>> - Add ref clk optional dt binding (Stephen Boyd)
>> - Add gpio-controller optional dt binding (Stephen Boyd)
>>
>> Changes in v5:
>> - Use clock property to specify the input refclk (Stephen Boyd).
>> - Update gpio cell and pwm cell numbers (Stephen Boyd).
>>
>> Changes in v6:
>> - Add property to mention the lane mapping scheme and polarity
>> inversion
>> (Stephen Boyd).
>>
>> Changes in v7:
>> - Detail description of lane mapping scheme dt property (Andrzej
>> Hajda/ Rob Herring).
>> - Removed HDP gpio binding, since the bridge uses IRQ signal to
>> determine HPD, and IRQ property is already documented in binding.
>>
>> Signed-off-by: Sandeep Panda <spanda at codeaurora.org>
>> ---
>> .../bindings/display/bridge/ti,sn65dsi86.txt | 109
>> +++++++++++++++++++++
>> 1 file changed, 109 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>>
>> diff --git
>> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>> new file mode 100644
>> index 0000000..33329f9
>> --- /dev/null
>> +++
>> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>> @@ -0,0 +1,109 @@
>> +SN65DSI86 DSI to eDP bridge chip
>> +--------------------------------
>> +
>> +This is the binding for Texas Instruments SN65DSI86 bridge.
>> +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
>> +
>> +Required properties:
>> +- compatible: Must be "ti,sn65dsi86"
>> +- reg: i2c address of the chip, 0x2d as per datasheet
>> +- enable-gpios: OF device-tree gpio specification for bridge_en pin
>> (active high)
>> +
>> +- vccio-supply: A 1.8V supply that powers up the digital IOs.
>> +- vpll-supply: A 1.8V supply that powers up the displayport PLL.
>> +- vcca-supply: A 1.2V supply that powers up the analog circuits.
>> +- vcc-supply: A 1.2V supply that powers up the digital core.
>> +
>> +Optional properties:
>> +- interrupts: Specifier for the SN65DSI86 interrupt line.
>> +
>> +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID
>> probing
>> +
>> +- gpio-controller: Marks the device has a GPIO controller.
>> +- #gpio-cells : Should be two. The first cell is the pin number
>> and
>> + the second cell is used to specify flags.
>> + See ../../gpio/gpio.txt for more information.
>> +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description
>> of
>> + the cell formats.
>> +
>> +- clock-names: should be "refclk"
>> +- clocks: Specification for input reference clock. The reference
>> + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
>> +
>> +- lane-mapping: Specification to describe the logical to physical
>> lane
>
> As I mentioned in v7, we already have a property for this. It's called
> 'data-lanes' and defined in media/video-interfaces.txt. Use that. If
> you
> need polarity too, then add a property for that. And add it to
> video-interfaces.txt.
The data-lanes property mentioned in media/video-interfaces.txt is
referring
to DSI/CSI lanes where assumption is clock lane is fixed at index 0. But
here
the we want to mention about eDP lanes which do not have dedicated clock
lane.
So can we still use the existing data-lanes property here?
>
>> + mapping scheme and polarity inversion of eDP lanes on PCB.
>> + Each pair present at index n (where n lies between 0 and 3)
>> + describes the lane mapping of logical lane to physical lane n
>> + and the polarity(it should be either 1 or 0) of the physical lane
>> n.
>> +
>> + For example:
>> + lane-mapping = <2 1>,
>> + <1 0>,
>> + <3 1>,
>> + <0 0>;
>> +
>> + The above mapping describes that logical lane 2 is mapped to
>> + physical lane 0 and polarity of physical lane 0 is inverted,
>> + logical lane 1 is mapped to physical lane 1 and polarity of
>> + physical lane 1 is normal, logical lane 3 is mapped to physical
>> + lane 2 and polarity of physical lane 2 is inverted, logical lane 0
>> + is mapped to physical lane 4 and polarity of physical lane 3 is
>> normal.
>> +
>> + If this property is not mentioned then it is assumed that physical
>> + lanes 0 through 3 are mapped to logical lanes 0 through 3 and
>> polarity
>> + of all physical lanes is normal.
>> +
>> +Required nodes:
>> +This device has two video ports. Their connections are modelled using
>> the
>> +OF graph bindings specified in
>> Documentation/devicetree/bindings/graph.txt.
>> +
>> +- Video port 0 for DSI input
>> +- Video port 1 for eDP output
>> +
>> +Example
>> +-------
>> +
>> +edp-bridge at 2d {
>> + compatible = "ti,sn65dsi86";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <0x2d>;
>> +
>> + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
>> + interrupt-parent = <&gpio3>;
>> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
>> +
>> + vccio-supply = <&pm8916_l17>;
>> + vcca-supply = <&pm8916_l6>;
>> + vpll-supply = <&pm8916_l17>;
>> + vcc-supply = <&pm8916_l6>;
>> +
>> + clock-names = "refclk";
>> + clocks = <&input_refclk>;
>> +
>> + lane-mapping = <0 0>, /* Logical lane 0 is routed to physical lane
>> 0 (!inv) */
>> + <1 1>, /* Logical lane 1 is routed to physical lane 1 (inv)
>> */
>> + <2 0>, /* Logical lane 2 is routed to physical lane 2 (!inv)
>> */
>> + <3 1>; /* Logical lane 3 is routed to physical lane 3 (inv)
>> */
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port at 0 {
>> + reg = <0>;
>> +
>> + edp_bridge_in: endpoint {
>> + remote-endpoint = <&dsi_out>;
>> + };
>> + };
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + edp_bridge_out: endpoint {
>> + remote-endpoint = <&edp_panel_in>;
>> + };
>> + };
>> + };
>> +}
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
>> Forum,
>> a Linux Foundation Collaborative Project
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree"
>> in
>> the body of a message to majordomo at vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the Freedreno
mailing list