[Freedreno] [PATCH RFC 11/11] ARM: dts: qcom: msm8974-hammerhead: add support for external display

[Brian Masney]

Add HDMI nodes and other supporting infrastructure in order to support
the external display. This is based on work from Jonathan Marek.

Signed-off-by: Brian Masney <masneyb at onstation.org>
---
The hdmi-tx node in the downstream MSM sources:
https://github.com/AICP/kernel_lge_hammerhead/blob/n7.1/arch/arm/boot/dts/msm8974-mdss.dtsi#L101

 .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 140 ++++++++++++++++++
 1 file changed, 140 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 3487daf98e81..83416b6d6634 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -234,6 +234,34 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&wlan_regulator_pin>;
 	};
+
+	anx_avdd33: avdd33 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "avdd-3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8941_gpios 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&anx_avdd33_pin>;
+	};
+
+	anx_vdd10: vdd10 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vdd-1p0";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+
+		gpio = <&pm8941_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&anx_vdd10_pin>;
+	};
 };
 
 &soc {
@@ -355,6 +383,40 @@
 				bias-disable;
 			};
 		};
+
+		hdmi_pin: hdmi {
+			cec {
+				pins = "gpio31";
+				function = "hdmi_cec";
+			};
+
+			ddc {
+				pins = "gpio32", "gpio33";
+				function = "hdmi_ddc";
+			};
+
+			hpd {
+				pins = "gpio34";
+				function = "hdmi_hpd";
+			};
+		};
+
+		anx_msm_pin: anx {
+			irq {
+				pins = "gpio28";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-pull-up;
+				input-enable;
+			};
+
+			reset {
+				pins = "gpio68";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-pull-up;
+			};
+		};
 	};
 
 	sdhci at f9824900 {
@@ -440,6 +502,28 @@
 				default-brightness = <200>;
 			};
 		};
+
+		anx7808 at 72 {
+			compatible = "analogix,anx7808";
+			reg = <0x72>;
+			interrupts-extended = <&msmgpio 28 IRQ_TYPE_EDGE_RISING>;
+
+			hpd-gpios = <&pm8941_gpios 13 GPIO_ACTIVE_HIGH>;
+			pd-gpios = <&pm8941_gpios 14 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&msmgpio 68 GPIO_ACTIVE_LOW>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&anx_msm_pin>, <&anx_pin>;
+
+			dvdd10-supply = <&anx_vdd10>;
+			avdd33-supply = <&anx_avdd33>;
+
+			port {
+				anx7808_in: endpoint {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+		};
 	};
 
 	i2c at f9968000 {
@@ -621,6 +705,29 @@
 
 			vddio-supply = <&pm8941_l12>;
 		};
+
+		hdmi-tx at fd922100 {
+			status = "ok";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&hdmi_pin>;
+
+			qcom,hdmi-tx-ddc-clk = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
+			qcom,hdmi-tx-ddc-data = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+			qcom,hdmi-tx-hpd = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+
+			ports {
+				port at 1 {
+					hdmi_out: endpoint {
+						remote-endpoint = <&anx7808_in>;
+					};
+				};
+			};
+		};
+
+		hdmi-phy at fd922500 {
+			status = "ok";
+		};
 	};
 };
 
@@ -657,6 +764,39 @@
 				output-high;
 				line-name = "otg-gpio";
 			};
+
+			anx_pin: anx {
+				cbldet {
+					pins = "gpio13";
+					function = "normal";
+					input-enable;
+					bias-pull-down;
+					power-source = <PM8941_GPIO_S3>;
+				};
+
+				pd {
+					pins = "gpio14";
+					function = "normal";
+					bias-disable;
+					power-source = <PM8941_GPIO_S3>;
+				};
+			};
+
+			anx_avdd33_pin: anxvdd3  {
+				pins = "gpio26";
+				function = "normal";
+
+				bias-disable;
+				power-source = <PM8941_GPIO_S3>;
+			};
+
+			anx_vdd10_pin: anxvdd1 {
+				pins = "gpio8";
+				function = "normal";
+
+				bias-disable;
+				power-source = <PM8941_GPIO_S3>;
+			};
 		};
 	};
 };
-- 
2.21.0