[Freedreno] [DPU PATCH v3 1/5] dt-bindings: msm/dp: add bindings of DP/DP-PLL driver for Snapdragon 845
Chandan Uddaraju
chandanu at codeaurora.org
Mon Dec 2 13:47:45 UTC 2019
Add bindings for Snapdragon 845 DisplayPort and
display-port PLL driver.
Changes in V2:
Provide details about sel-gpio
Signed-off-by: Chandan Uddaraju <chandanu at codeaurora.org>
---
.../devicetree/bindings/display/msm/dp.txt | 249 +++++++++++++++++++++
.../devicetree/bindings/display/msm/dpu.txt | 16 +-
2 files changed, 261 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/msm/dp.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dp.txt b/Documentation/devicetree/bindings/display/msm/dp.txt
new file mode 100644
index 0000000..38be36d
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dp.txt
@@ -0,0 +1,249 @@
+Qualcomm Technologies, Inc.
+DP is the master Display Port device which supports DP host controllers that are compatible with VESA Display Port interface specification.
+DP Controller: Required properties:
+- compatible: Should be "qcom,dp-display".
+- reg: Base address and length of DP hardware's memory mapped regions.
+- cell-index: Specifies the controller instance.
+- reg-names: A list of strings that name the list of regs.
+ "dp_ahb" - DP controller memory region.
+ "dp_aux" - DP AUX memory region.
+ "dp_link" - DP link layer memory region.
+ "dp_p0" - DP pixel clock domain memory region.
+ "dp_phy" - DP PHY memory region.
+ "dp_ln_tx0" - USB3 DP PHY combo TX-0 lane memory region.
+ "dp_ln_tx1" - USB3 DP PHY combo TX-1 lane memory region.
+ "dp_mmss_cc" - Display Clock Control memory region.
+ "qfprom_physical" - QFPROM Phys memory region.
+ "dp_pll" - USB3 DP combo PLL memory region.
+ "usb3_dp_com" - USB3 DP PHY combo memory region.
+ "hdcp_physical" - DP HDCP memory region.
+- interrupt-parent phandle to the interrupt parent device node.
+- interrupts: The interrupt signal from the DP block.
+- clocks: Clocks required for Display Port operation. See [1] for details on clock bindings.
+- clock-names: Names of the clocks corresponding to handles. Following clocks are required:
+ "core_aux_clk", "core_usb_ref_clk_src","core_usb_ref_clk", "core_usb_cfg_ahb_clk",
+ "core_usb_pipe_clk", "ctrl_link_clk", "ctrl_link_iface_clk", "ctrl_crypto_clk",
+ "ctrl_pixel_clk", "pixel_clk_rcg", "pixel_parent".
+- pll-node: phandle to DP PLL node.
+- vdda-1p2-supply: phandle to vdda 1.2V regulator node.
+- vdda-0p9-supply: phandle to vdda 0.9V regulator node.
+- qcom,aux-cfg0-settings: Specifies the DP AUX configuration 0 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg1-settings: Specifies the DP AUX configuration 1 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg2-settings: Specifies the DP AUX configuration 2 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg3-settings: Specifies the DP AUX configuration 3 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg4-settings: Specifies the DP AUX configuration 4 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg5-settings: Specifies the DP AUX configuration 5 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg6-settings: Specifies the DP AUX configuration 6 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg7-settings: Specifies the DP AUX configuration 7 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg8-settings: Specifies the DP AUX configuration 8 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,aux-cfg9-settings: Specifies the DP AUX configuration 9 settings. The first
+ entry in this array corresponds to the register offset
+ within DP AUX, while the remaining entries indicate the
+ programmable values.
+- qcom,max-pclk-frequency-khz: An integer specifying the maximum. pixel clock in KHz supported by Display Port.
+- extcon: Phandle for the external connector class interface.
+- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the a particular "type" of DP module. The module "types"
+ can be "core", "ctrl", and "phy". Within the same type,
+ there can be more than one instance of this binding,
+ in which case the entry would be appended with the
+ supply entry index.
+ e.g. qcom,ctrl-supply-entry at 0
+ -- qcom,supply-name: name of the supply (vdd/vdda/vddio)
+ -- qcom,supply-min-voltage: minimum voltage level (uV)
+ -- qcom,supply-max-voltage: maximum voltage level (uV)
+ -- qcom,supply-enable-load: load drawn (uA) from enabled supply
+ -- qcom,supply-disable-load: load drawn (uA) from disabled supply
+ -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
+ -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
+ -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
+ -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
+- pinctrl-names: List of names to assign mdss pin states defined in pinctrl device node
+ Refer to pinctrl-bindings.txt
+- pinctrl-<0..n>: Lists phandles each pointing to the pin configuration node within a pin
+ controller. These pin configurations are installed in the pinctrl
+ device node. Refer to pinctrl-bindings.txt
+DP Endpoint properties:
+ - remote-endpoint: For port at 0, set to phandle of the connected panel/bridge's
+ input endpoint. For port at 1, set to the DPU interface output. See [2] for
+ device graph info.
+
+Optional properties:
+- qcom,aux-en-gpio: Specifies the aux-channel enable gpio.
+- qcom,aux-sel-gpio: Specifies the mux-selection that might be needed for aux interface.
+
+
+DP PLL: Required properties:
+- compatible: Should be "qcom,dp-pll-10nm".
+- reg: Base address and length of DP hardware's memory mapped regions.
+- cell-index: Specifies the PLL instance.
+- reg-names: A list of strings that name the list of regs.
+ "pll_base" - DP PLL memory region.
+ "phy_base" - DP PHY memory region.
+ "ln_tx0_base" - USB3 DP PHY combo TX-0 lane memory region.
+ "ln_tx1_base" - USB3 DP PHY combo TX-1 lane memory region.
+ "gdsc_base" - gdsc memory region.
+- interrupt-parent phandle to the interrupt parent device node.
+- interrupts: The interrupt signal from the DP block.
+- clocks: Clocks required for Display Port operation. See [1] for details on clock bindings.
+- clock-names: Names of the clocks corresponding to handles. Following clocks are required:
+ "iface_clk", "ref_clk", cfg_ahb_clk", "pipe_clk".
+- clock-rate: Initial clock rate to be configured. For the shared clocks, the default value is set to zero so that minimum clock value is configured. Non-zero clock
+ value can be used to configure DP pixel clock.
+
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/graph.txt
+
+Example:
+ msm_dp: dp_display at ae90000{
+ cell-index = <0>;
+ compatible = "qcom,dp-display";
+
+ reg = <0 0x90000 0x0dc>,
+ <0 0x90200 0x0c0>,
+ <0 0x90400 0x508>,
+ <0 0x90a00 0x094>,
+ <1 0xeaa00 0x200>,
+ <1 0xea200 0x200>,
+ <1 0xea600 0x200>,
+ <2 0x02000 0x1a0>,
+ <3 0x00000 0x621c>,
+ <1 0xea000 0x180>,
+ <1 0xe8000 0x20>,
+ <4 0xe1000 0x034>;
+ reg-names = "dp_ahb", "dp_aux", "dp_link",
+ "dp_p0", "dp_phy", "dp_ln_tx0", "dp_ln_tx1",
+ "dp_mmss_cc", "qfprom_physical", "dp_pll",
+ "usb3_dp_com", "hdcp_physical";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <12 0>;
+
+ extcon = <&usb_1_ssphy>;
+ clocks = <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_CRYPTO_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+ clock-names = "core_aux_clk", "core_ref_clk_src",
+ "core_usb_ref_clk", "core_usb_cfg_ahb_clk",
+ "core_usb_pipe_clk", "ctrl_link_clk",
+ "ctrl_link_iface_clk", "ctrl_pixel_clk",
+ "crypto_clk", "pixel_clk_rcg";
+
+ pll-node = <&dp_pll>;
+ qcom,aux-cfg0-settings = [20 00];
+ qcom,aux-cfg1-settings = [24 13 23 1d];
+ qcom,aux-cfg2-settings = [28 24];
+ qcom,aux-cfg3-settings = [2c 00];
+ qcom,aux-cfg4-settings = [30 0a];
+ qcom,aux-cfg5-settings = [34 26];
+ qcom,aux-cfg6-settings = [38 0a];
+ qcom,aux-cfg7-settings = [3c 03];
+ qcom,aux-cfg8-settings = [40 bb];
+ qcom,aux-cfg9-settings = [44 03];
+
+ qcom,max-pclk-frequency-khz = <675000>;
+
+ qcom,ctrl-supply-entries {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qcom,ctrl-supply-entry at 0 {
+ reg = <0>;
+ qcom,supply-name = "vdda-1p2";
+ qcom,supply-min-voltage = <1200000>;
+ qcom,supply-max-voltage = <1200000>;
+ qcom,supply-enable-load = <21800>;
+ qcom,supply-disable-load = <4>;
+ };
+ };
+
+ qcom,phy-supply-entries {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qcom,phy-supply-entry at 0 {
+ reg = <0>;
+ qcom,supply-name = "vdda-0p9";
+ qcom,supply-min-voltage = <880000>;
+ qcom,supply-max-voltage = <880000>;
+ qcom,supply-enable-load = <36000>;
+ qcom,supply-disable-load = <32>;
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ dp_in: endpoint {
+ remote-endpoint = <&dpu_intf0_out>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ dp_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dp_pll: dp-pll at c011000 {
+ compatible = "qcom,dp-pll-10nm";
+ label = "DP PLL";
+ cell-index = <0>;
+ #clock-cells = <1>;
+
+ reg = <1 0xea000 0x200>,
+ <1 0xeaa00 0x200>,
+ <1 0xea200 0x200>,
+ <1 0xea600 0x200>,
+ <2 0x03000 0x8>;
+ reg-names = "pll_base", "phy_base", "ln_tx0_base",
+ "ln_tx1_base", "gdsc_base";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "iface_clk", "ref_clk",
+ "cfg_ahb_clk", "pipe_clk";
+ clock-rate = <0>;
+
+ };
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
index a61dd40..eac6e1c 100644
--- a/Documentation/devicetree/bindings/display/msm/dpu.txt
+++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
@@ -63,8 +63,9 @@ Required properties:
Documentation/devicetree/bindings/graph.txt
Documentation/devicetree/bindings/media/video-interfaces.txt
- Port 0 -> DPU_INTF1 (DSI1)
- Port 1 -> DPU_INTF2 (DSI2)
+ Port 0 -> DPU_INTF0 (DP)
+ Port 1 -> DPU_INTF1 (DSI1)
+ Port 2 -> DPU_INTF2 (DSI2)
Optional properties:
- assigned-clocks: list of clock specifiers for clocks needing rate assignment
@@ -125,13 +126,20 @@ Example:
port at 0 {
reg = <0>;
- dpu_intf1_out: endpoint {
- remote-endpoint = <&dsi0_in>;
+ dpu_intf0_out: endpoint {
+ remote-endpoint = <&dp_in>;
};
};
port at 1 {
reg = <1>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
dpu_intf2_out: endpoint {
remote-endpoint = <&dsi1_in>;
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
More information about the Freedreno
mailing list