[Freedreno] [PATCH v10 3/5] drm/msm/dp: add support for DP PLL driver

[Jonathan Marek]

On 8/15/20 4:20 PM, Rob Clark wrote:
> On Fri, Aug 14, 2020 at 10:05 AM Dmitry Baryshkov
> <dmitry.baryshkov at linaro.org> wrote:
>>
>>
>> On 12/08/2020 07:42, Tanmay Shah wrote:
>>   > From: Chandan Uddaraju <chandanu at codeaurora.org>
>>   >
>>   > Add the needed DP PLL specific files to support
>>   > display port interface on msm targets.
>>
>> [skipped]
>>
>>   > diff --git a/drivers/gpu/drm/msm/dp/dp_pll_private.h
>> b/drivers/gpu/drm/msm/dp/dp_pll_private.h
>>   > new file mode 100644
>>   > index 000000000000..475ba6ed59ab
>>   > --- /dev/null
>>   > +++ b/drivers/gpu/drm/msm/dp/dp_pll_private.h
>>   > @@ -0,0 +1,98 @@
>>   > +/* SPDX-License-Identifier: GPL-2.0-only */
>>   > +/*
>>   > + * Copyright (c) 2016-2020, The Linux Foundation. All rights reserved.
>>   > + */
>>   > +
>>   > +#ifndef __DP_PLL_10NM_H
>>   > +#define __DP_PLL_10NM_H
>>   > +
>>   > +#include "dp_pll.h"
>>   > +#include "dp_reg.h"
>>   > +
>>   > +#define DP_VCO_HSCLK_RATE_1620MHZDIV1000    1620000UL
>>   > +#define DP_VCO_HSCLK_RATE_2700MHZDIV1000    2700000UL
>>   > +#define DP_VCO_HSCLK_RATE_5400MHZDIV1000    5400000UL
>>   > +#define DP_VCO_HSCLK_RATE_8100MHZDIV1000    8100000UL
>>   > +
>>   > +#define NUM_DP_CLOCKS_MAX            6
>>   > +
>>   > +#define DP_PHY_PLL_POLL_SLEEP_US        500
>>   > +#define DP_PHY_PLL_POLL_TIMEOUT_US        10000
>>   > +
>>   > +#define DP_VCO_RATE_8100MHZDIV1000        8100000UL
>>   > +#define DP_VCO_RATE_9720MHZDIV1000        9720000UL
>>   > +#define DP_VCO_RATE_10800MHZDIV1000        10800000UL
>>   > +
>>   > +struct dp_pll_vco_clk {
>>   > +    struct clk_hw hw;
>>   > +    unsigned long    rate;        /* current vco rate */
>>   > +    u64        min_rate;    /* min vco rate */
>>   > +    u64        max_rate;    /* max vco rate */
>>   > +    void        *priv;
>>   > +};
>>   > +
>>   > +struct dp_pll_db {
>>
>> This struct should probably go into dp_pll_10nm.c. dp_pll_7nm.c, for
>> example, will use slightly different structure.
> 
> Note that sboyd has a WIP series to move all of the pll code out to a
> phy driver.  If there is work already happening on 7nm support, it
> might be better to go with the separate phy driver approach?  I'm
> still a bit undecided about whether to land the dp code initially with
> the pll stuff in drm, and then continue refactoring to move to
> separate phy driver upstream, or to strip out the pll code from the
> beginning.  If you/someone is working on 7nm support, then feedback
> about which approach is easier is welcome.
> 
> https://lore.kernel.org/dri-devel/20200611091919.108018-1-swboyd@chromium.org/
> 

I have a sm8150/sm8250 (7nm) upstream kernel stack with DP enabled, and 
I have done something similar, with the PLL driver in the QMP phy, 
although not based on sboyd's series (along with some typec changes to 
negotiate the DP alt mode and get HPD events, etc.). I don't think 
having PLL in drm/msm makes sense, the drm/msm DP driver shouldn't need 
to be aware of the DP PLL/PHY driver, it only needs to set the 
link/pixel clock rates which are in dispcc (and those then have the PLL 
clocks as a parent).

FYI, since it sounds you are considering landing this: it is completely 
broken, for example:
- ioremap()'s to #define'd addresses in the PLL driver
- main DP driver reading/writing to registers in the PHY region, but 
getting the base address from devicetree was removed since earlier 
revisions, so it just fails completely. Look at usb3_dp_com (for 
example), which in dp_catalog_ctrl_usb_reset() would be used to 
overwrite registers already being driven by the qmp phy driver - but now 
the usb3_dp_com.base is never initialized.

-Jonathan

> BR,
> -R
> _______________________________________________
> Freedreno mailing list
> Freedreno at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/freedreno
>