[Freedreno] [v1] drm/msm/dsi/pll: call vco set rate explicitly

[Rob Clark]

On Mon, Feb 10, 2020 at 9:58 PM <harigovi at codeaurora.org> wrote:
>
> On 2020-02-07 19:40, Jeffrey Hugo wrote:
> > On Fri, Feb 7, 2020 at 5:38 AM <harigovi at codeaurora.org> wrote:
> >>
> >> On 2020-02-06 20:29, Jeffrey Hugo wrote:
> >> > On Thu, Feb 6, 2020 at 2:13 AM Harigovindan P <harigovi at codeaurora.org>
> >> > wrote:
> >> >>
> >> >> For a given byte clock, if VCO recalc value is exactly same as
> >> >> vco set rate value, vco_set_rate does not get called assuming
> >> >> VCO is already set to required value. But Due to GDSC toggle,
> >> >> VCO values are erased in the HW. To make sure VCO is programmed
> >> >> correctly, we forcefully call set_rate from vco_prepare.
> >> >
> >> > Is this specific to certain SoCs? I don't think I've observed this.
> >>
> >> As far as Qualcomm SOCs are concerned, since pll is analog and the
> >> value
> >> is directly read from hardware if we get recalc value same as set rate
> >> value, the vco_set_rate will not be invoked. We checked in our idp
> >> device which has the same SOC but it works there since the rates are
> >> different.
> >
> > This doesn't seem to be an answer to my question.  What Qualcomm SoCs
> > does this issue apply to?  Everything implementing the 10nm pll?  One
> > specific SoC?  I don't believe I've seen this on MSM8998, nor SDM845,
> > so I'm interested to know what is the actual impact here.  I don't see
> > an "IDP" SoC in the IP catalog, so I really have no idea what you are
> > referring to.
>
>
> This is not 10nm specific. It is applicable for other nms also.
> Its specific to the frequency being set. If vco_recalc returns the same
> value as being set by vco_set_rate,
> vco_set_rate will not be invoked second time onwards.
>
> For example: Lets take below devices:
>
> Cheza is based on SDM845 which is 10nm only.
> Clk frequency:206016
> dsi_pll_10nm_vco_set_rate - DSI PLL0 rate=1236096000
> dsi_pll_10nm_vco_recalc_rate - DSI PLL0 returning vco rate = 1236095947
>
> Trogdor is based on sc7180 which is also 10nm.
> Clk frequency:69300
> dsi_pll_10nm_vco_set_rate - DSI PLL0 rate=1663200000
> dsi_pll_10nm_vco_recalc_rate - DSI PLL0 returning vco rate = 1663200000
>
> In same trogdor device, we slightly changed the clock frequency and the
> values actually differ which will not cause any issue.
> Clk frequency:69310
> dsi_pll_10nm_vco_set_rate - DSI PLL0 rate=1663440000
> dsi_pll_10nm_vco_recalc_rate - DSI PLL0 returning vco rate = 1663439941


tbh, loosing state when power is off is kind of the behavior that I'd
expect.  It kinda makes me wonder if things are not getting powered
off all the way on some SoCs?

jhugo, are you worried that this patch will cause problems on other
users of the 10nm pll?

BR,
-R