[Freedreno] [v5] dt-bindings: msm: disp: add yaml schemas for DPU and DSI bindings
Rob Herring
robh at kernel.org
Mon Jul 13 16:28:28 UTC 2020
On Fri, Jul 10, 2020 at 07:27:49PM +0530, Krishna Manikandan wrote:
> MSM Mobile Display Subsytem (MDSS) encapsulates sub-blocks
> like DPU display controller, DSI etc. Add YAML schema
> for the device tree bindings for the same.
>
> Signed-off-by: Krishna Manikandan <mkrishn at codeaurora.org>
>
> Changes in v2:
> - Changed dpu to DPU (Sam Ravnborg)
> - Fixed indentation issues (Sam Ravnborg)
> - Added empty line between different properties (Sam Ravnborg)
> - Replaced reference txt files with their corresponding
> yaml files (Sam Ravnborg)
> - Modified the file to use "|" only when it is
> necessary (Sam Ravnborg)
>
> Changes in v3:
> - Corrected the license used (Rob Herring)
> - Added maxItems for properties (Rob Herring)
> - Dropped generic descriptions (Rob Herring)
> - Added ranges property (Rob Herring)
> - Corrected the indendation (Rob Herring)
> - Added additionalProperties (Rob Herring)
> - Split dsi file into two, one for dsi controller
> and another one for dsi phy per target (Rob Herring)
> - Corrected description for pinctrl-names (Rob Herring)
> - Corrected the examples used in yaml file (Rob Herring)
> - Delete dsi.txt and dpu.txt (Rob Herring)
>
> Changes in v4:
> - Move schema up by one level (Rob Herring)
> - Add patternProperties for mdp node (Rob Herring)
> - Corrected description of some properties (Rob Herring)
>
> Changes in v5:
> - Correct the indentation (Rob Herring)
> - Remove unnecessary description from properties (Rob Herring)
> - Correct the number of interconnect entries (Rob Herring)
> - Add interconnect names for sc7180 (Rob Herring)
> - Add description for ports (Rob Herring)
> - Remove common properties (Rob Herring)
> - Add unevalutatedProperties (Rob Herring)
> - Reference existing dsi controller yaml in the common
> dsi controller file (Rob Herring)
> - Correct the description of clock names to include only the
> clocks that are required (Rob Herring)
> - Remove properties which are already covered under the common
> binding (Rob Herring)
> - Add dsi phy supply nodes which are required for sc7180 and
> sdm845 targets (Rob Herring)
> - Add type ref for syscon-sfpb (Rob Herring)
> ---
> .../bindings/display/dsi-controller.yaml | 4 +-
> .../bindings/display/msm/dpu-sc7180.yaml | 230 +++++++++++++++++++
> .../bindings/display/msm/dpu-sdm845.yaml | 210 ++++++++++++++++++
> .../devicetree/bindings/display/msm/dpu.txt | 141 ------------
> .../display/msm/dsi-common-controller.yaml | 178 +++++++++++++++
> .../display/msm/dsi-controller-sc7180.yaml | 115 ++++++++++
> .../display/msm/dsi-controller-sdm845.yaml | 115 ++++++++++
> .../bindings/display/msm/dsi-phy-sc7180.yaml | 79 +++++++
> .../bindings/display/msm/dsi-phy-sdm845.yaml | 81 +++++++
> .../devicetree/bindings/display/msm/dsi-phy.yaml | 79 +++++++
> .../devicetree/bindings/display/msm/dsi.txt | 246 ---------------------
> 11 files changed, 1089 insertions(+), 389 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/dsi-controller.yaml b/Documentation/devicetree/bindings/display/dsi-controller.yaml
> index fd986c3..85b71b1 100644
> --- a/Documentation/devicetree/bindings/display/dsi-controller.yaml
> +++ b/Documentation/devicetree/bindings/display/dsi-controller.yaml
> @@ -28,7 +28,7 @@ description: |
>
> properties:
> $nodename:
> - pattern: "^dsi-controller(@.*)?$"
> + pattern: "^dsi(@.*)?$"
>
> "#address-cells":
> const: 1
> @@ -76,7 +76,7 @@ patternProperties:
> examples:
> - |
> #include <dt-bindings/gpio/gpio.h>
> - dsi-controller at a0351000 {
> + dsi at a0351000 {
> reg = <0xa0351000 0x1000>;
> #address-cells = <1>;
> #size-cells = <0>;
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
> new file mode 100644
> index 0000000..3afa85c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
> @@ -0,0 +1,230 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dpu-sc7180.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DPU dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
> + sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
> + bindings of MDSS and DPU are mentioned for SC7180 target.
> +
> +properties:
> + compatible:
> + items:
> + - const: qcom,sc7180-mdss
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: mdss
> +
> + power-domains:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 3
> +
> + clock-names:
> + items:
> + - const: iface
> + - const: ahb
> + - const: core
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + "#interrupt-cells":
> + const: 1
> +
> + iommus:
> + maxItems: 1
> +
> + "#address-cells":
> + const: 2
> +
> + "#size-cells":
> + const: 2
> +
> + ranges: true
> +
> + interconnects:
> + description: |
> + Interconnect path specifier for MDSS according to
> + Documentation/devicetree/bindings/interconnect/interconnect.txt.
> + An entry should contain 2 paths corresponding to 2 AXI ports representing
> + source and destination ports.
> + minItems: 1
> +
> + interconnect-names:
> + description: |
> + MDSS will have 2 port names to differentiate between the
> + 2 interconnect paths defined with interconnect specifier.
> + items:
> + - const: mdp0-mem
> +
> + assigned-clocks:
> + maxItems: 1
> +
> + assigned-clock-rates:
> + maxItems: 1
> +
> +patternProperties:
> + "^mdp@[0-9a-f]+$":
> + type: object
> + description: Node containing the properties of DPU.
> +
> + properties:
> + compatible:
> + items:
> + - const: qcom,sc7180-dpu
> +
> + reg:
> + maxItems: 2
> +
> + reg-names:
> + items:
> + - const: mdp
> + - const: vbif
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + description: |
> + Device clock names, must be in same order as clocks property.
> + The following clocks are required.
> + items:
> + - const: bus
> + - const: iface
> + - const: rot
> + - const: lut
> + - const: core
> + - const: vsync
> +
> + interrupts:
> + maxItems: 1
> +
> + ports:
> + type: object
> + description: |
> + Contains the list of output ports from DPU device. These ports
> + connect to interfaces that are external to the DPU hardware,
> + such as DSI, DP etc. Each output port contains an endpoint that
> + describes how it is connected to an external interface. These
> + are described by the standard properties documented in files
> + mentioned below.
> +
> + Documentation/devicetree/bindings/graph.txt
> + Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> + properties:
> + port at 0:
> + type: object
> + description: DPU_INTF1 (DSI1)
> + port at 1:
> + type: object
> + description: DPU_INTF2 (DSI2)
> +
> + assigned-clocks:
> + maxItems: 4
> +
> + assigned-clock-rates:
> + maxItems: 4
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - power-domains
> + - clocks
> + - clock-names
> + - interrupts
> + - interrupt-controller
> + - iommus
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/interconnect/qcom,sdm845.h>
> + mdss: mdss at ae00000 {
> + compatible = "qcom,sc7180-mdss";
> + reg = <0 0xae00000 0 0x1000>;
> + reg-names = "mdss";
> + power-domains = <&dispcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +
> + clock-names = "iface", "ahb", "core";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + assigned-clock-rates = <300000000>;
> +
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>;
> +
> + interconnect-names = "mdp0-mem";
> +
> + iommus = <&apps_smmu 0x800 0x2>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + mdp: mdp at ae01000 {
> + compatible = "qcom,sc7180-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> +
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_ROT_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus", "iface", "rot", "lut", "core",
> + "vsync";
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
> + <&dispcc DISP_CC_MDSS_ROT_CLK>,
> + <&dispcc DISP_CC_MDSS_ROT_CLK>;
> + assigned-clock-rates = <300000000>,
> + <19200000>,
> + <19200000>,
> + <19200000>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> + };
> + };
> + };
> +...
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
> new file mode 100644
> index 0000000..7848617
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
> @@ -0,0 +1,210 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DPU dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
> + sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
> + bindings of MDSS and DPU are mentioned for SDM845 target.
> +
> +properties:
> + compatible:
> + items:
> + - const: qcom,sdm845-mdss
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: mdss
> +
> + power-domains:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 3
> +
> + clock-names:
> + description: |
> + Device clock names in the same order as mentioned in clocks property.
> + The required clocks are mentioned below.
> + items:
> + - const: iface
> + - const: bus
> + - const: core
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + "#interrupt-cells":
> + const: 1
> +
> + iommus:
> + maxItems: 2
> +
> + "#address-cells":
> + const: 2
> +
> + "#size-cells":
> + const: 2
> +
> + ranges: true
> +
> + assigned-clocks:
> + maxItems: 1
> +
> + assigned-clock-rates:
> + maxItems: 1
> +
> +patternProperties:
> + "^mdp@[0-9a-f]+$":
> + type: object
> + description: Node containing the properties of DPU.
> +
> + properties:
> + compatible:
> + items:
> + - const: qcom,sdm845-dpu
> + reg:
> + maxItems: 2
> +
> + reg-names:
> + items:
> + - const: mdp
> + - const: vbif
> +
> + clocks:
> + maxItems: 4
> +
> + clock-names:
> + description: |
> + Device clock names, must be in same order as clocks property.
> + The following clocks are required.
> + items:
> + - const: iface
> + - const: bus
> + - const: core
> + - const: vsync
> +
> + interrupts:
> + maxItems: 1
> +
> + ports:
> + type: object
> + description: |
> + Contains the list of output ports from DPU device. These ports
> + connect to interfaces that are external to the DPU hardware,
> + such as DSI, DP etc. Each output port contains an endpoint that
> + describes how it is connected to an external interface. These
> + are described by the standard properties documented in files
> + mentioned below.
> +
> + Documentation/devicetree/bindings/graph.txt
> + Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> + properties:
> + port at 0:
> + type: object
> + description: DPU_INTF1 (DSI1)
> + port at 1:
> + type: object
> + description: DPU_INTF2 (DSI2)
> +
> + assigned-clocks:
> + maxItems: 2
> +
> + assigned-clock-rates:
> + maxItems: 2
> +
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - power-domains
> + - clocks
> + - clock-names
> + - interrupts
> + - interrupt-controller
> + - iommus
> +
> +additionalProperties: false
> +
> +examples:
> +- |
> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + mdss: mdss at ae00000 {
> + compatible = "qcom,sdm845-mdss";
> + reg = <0 0x0ae00000 0 0x1000>;
> + reg-names = "mdss";
> + power-domains = <&dispcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&gcc GCC_DISP_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface", "bus", "core";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + assigned-clock-rates = <300000000>;
> +
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + iommus = <&apps_smmu 0x880 0x8>,
> + <&apps_smmu 0xc80 0x8>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + mdss_mdp: mdp at ae01000 {
> + compatible = "qcom,sdm845-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "iface", "bus", "core", "vsync";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <300000000>,
> + <19200000>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dpu_intf2_out: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> + };
> +...
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
> deleted file mode 100644
> index 551ae26..0000000
> --- a/Documentation/devicetree/bindings/display/msm/dpu.txt
> +++ /dev/null
> @@ -1,141 +0,0 @@
> -Qualcomm Technologies, Inc. DPU KMS
> -
> -Description:
> -
> -Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
> -sub-blocks like DPU display controller, DSI and DP interfaces etc.
> -The DPU display controller is found in SDM845 SoC.
> -
> -MDSS:
> -Required properties:
> -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss"
> -- reg: physical base address and length of contoller's registers.
> -- reg-names: register region names. The following region is required:
> - * "mdss"
> -- power-domains: a power domain consumer specifier according to
> - Documentation/devicetree/bindings/power/power_domain.txt
> -- clocks: list of clock specifiers for clocks needed by the device.
> -- clock-names: device clock names, must be in same order as clocks property.
> - The following clocks are required:
> - * "iface"
> - * "bus"
> - * "core"
> -- interrupts: interrupt signal from MDSS.
> -- interrupt-controller: identifies the node as an interrupt controller.
> -- #interrupt-cells: specifies the number of cells needed to encode an interrupt
> - source, should be 1.
> -- iommus: phandle of iommu device node.
> -- #address-cells: number of address cells for the MDSS children. Should be 1.
> -- #size-cells: Should be 1.
> -- ranges: parent bus address space is the same as the child bus address space.
> -- interconnects : interconnect path specifier for MDSS according to
> - Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be
> - 2 paths corresponding to 2 AXI ports.
> -- interconnect-names : MDSS will have 2 port names to differentiate between the
> - 2 interconnect paths defined with interconnect specifier.
> -
> -Optional properties:
> -- assigned-clocks: list of clock specifiers for clocks needing rate assignment
> -- assigned-clock-rates: list of clock frequencies sorted in the same order as
> - the assigned-clocks property.
> -
> -MDP:
> -Required properties:
> -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu"
> -- reg: physical base address and length of controller's registers.
> -- reg-names : register region names. The following region is required:
> - * "mdp"
> - * "vbif"
> -- clocks: list of clock specifiers for clocks needed by the device.
> -- clock-names: device clock names, must be in same order as clocks property.
> - The following clocks are required.
> - * "bus"
> - * "iface"
> - * "core"
> - * "vsync"
> -- interrupts: interrupt line from DPU to MDSS.
> -- ports: contains the list of output ports from DPU device. These ports connect
> - to interfaces that are external to the DPU hardware, such as DSI, DP etc.
> -
> - Each output port contains an endpoint that describes how it is connected to an
> - external interface. These are described by the standard properties documented
> - here:
> - Documentation/devicetree/bindings/graph.txt
> - Documentation/devicetree/bindings/media/video-interfaces.txt
> -
> - Port 0 -> DPU_INTF1 (DSI1)
> - Port 1 -> DPU_INTF2 (DSI2)
> -
> -Optional properties:
> -- assigned-clocks: list of clock specifiers for clocks needing rate assignment
> -- assigned-clock-rates: list of clock frequencies sorted in the same order as
> - the assigned-clocks property.
> -
> -Example:
> -
> - mdss: mdss at ae00000 {
> - compatible = "qcom,sdm845-mdss";
> - reg = <0xae00000 0x1000>;
> - reg-names = "mdss";
> -
> - power-domains = <&clock_dispcc 0>;
> -
> - clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
> - <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
> - clock-names = "iface", "bus", "core";
> -
> - assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
> - assigned-clock-rates = <300000000>;
> -
> - interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-controller;
> - #interrupt-cells = <1>;
> -
> - interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>,
> - <&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>;
> -
> - interconnect-names = "mdp0-mem", "mdp1-mem";
> -
> - iommus = <&apps_iommu 0>;
> -
> - #address-cells = <2>;
> - #size-cells = <1>;
> - ranges = <0 0 0xae00000 0xb2008>;
> -
> - mdss_mdp: mdp at ae01000 {
> - compatible = "qcom,sdm845-dpu";
> - reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>;
> - reg-names = "mdp", "vbif";
> -
> - clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
> - <&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
> - <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
> - <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
> - clock-names = "iface", "bus", "core", "vsync";
> -
> - assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
> - <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
> - assigned-clock-rates = <0 0 300000000 19200000>;
> -
> - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port at 0 {
> - reg = <0>;
> - dpu_intf1_out: endpoint {
> - remote-endpoint = <&dsi0_in>;
> - };
> - };
> -
> - port at 1 {
> - reg = <1>;
> - dpu_intf2_out: endpoint {
> - remote-endpoint = <&dsi1_in>;
> - };
> - };
> - };
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml b/Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml
> new file mode 100644
> index 0000000..39f7ee4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml
> @@ -0,0 +1,178 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-common-controller.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI controller dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Common Device tree bindings for DSI controller.
> +
> +allOf:
> + - $ref: "../dsi-controller.yaml#"
> +
> +properties:
> + compatible:
> + items:
> + - const: qcom,mdss-dsi-ctrl
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + description: |
> + Device clock names in the same order as mentioned in clocks property.
> +
> + assigned-clocks:
> + description: Parents of "byte" and "pixel" for the given platform.
> +
> + assigned-clock-parents:
> + description: |
> + The Byte clock and Pixel clock PLL outputs provided by a DSI PHY block.
> + Details on clock bindings are mentioned in
> + Documentation/devicetree/bindings/clock/clock-bindings.txt.
> +
> + vdd-supply:
> + description: Phandle to vdd regulator device node.
> +
> + vddio-supply:
> + description: Phandle to vdd-io regulator device node.
> +
> + vdda-supply:
> + description: Phandle to vdda regulator device node.
> +
> + phys:
> + description: Phandle to DSI PHY device node.
> +
> + phy-names:
> + description: Name of the corresponding PHY device.
No point in these 2 here as there are no constraints.
> +
> + syscon-sfpb:
> + description: A phandle to mmss_sfpb syscon node (only for DSIv2).
> + $ref: "/schemas/types.yaml#/definitions/phandle"
> +
> + # Optional Properties for dsi controller
> + qcom,mdss-mdp-transfer-time-us:
> + description: |
> + Specifies the DSI transfer time for command mode
> + panels in microseconds. Driver uses this number to adjust
> + the clock rate according to the expected transfer time.
> + Increasing this value would slow down the mdp processing
> + and can result in slower performance.
> + Decreasing this value can speed up the mdp processing,
> + but this can also impact power consumption.
> + As a rule this time should not be higher than the time
> + that would be expected with the processing at the
> + DSI link rate since anyways this would be the maximum
> + transfer time that could be achieved.
> + If ping pong split is enabled, this time should not be higher
> + than two times the DSI link rate time.
> + If the property is not specified, then the default value is
> + 14000 us. This is an optional property.
> +
> + qcom,dual-dsi-mode:
> + type: boolean
> + description: |
> + Boolean value indicating if the DSI controller is
> + driving a panel which needs 2 DSI links.
> +
> + qcom,master-dsi:
> + type: boolean
> + description: |
> + Boolean value indicating if the DSI controller is driving
> + the master link of the 2-DSI panel.
> +
> + qcom,sync-dual-dsi:
> + type: boolean
> + description: |
> + Boolean value indicating if the DSI controller is driving a
> + 2-DSI panel whose 2 links need receive command simultaneously.
> +
> + pinctrl-names:
> + description: The pin control state names.
> + items:
> + - const: default
> + - const: sleep
> +
> + pinctrl-0:
> + description: The default pinctrl state (active)
> +
> + pinctrl-1:
> + description: The sleep pinctrl state (suspend)
> +
> + ports:
> + type: object
> + description: |
> + Contains DSI controller input and output ports as children, each
> + containing one endpoint subnode as defined in
> + Documentation/devicetree/bindings/graph.txt and
> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> + properties:
> + port at 0:
> + type: object
> + description: |
> + Input endpoints of the controller.
> +
> + properties:
> + reg:
> + const: 0
> +
> + endpoint:
> + type: object
> + properties:
> + remote-endpoint:
> + description: |
> + For port at 0, set to phandle of the connected panel/bridge's
> + input endpoint. For port at 1, set to the MDP interface output.
> + See Documentation/devicetree/bindings/graph.txt for
> + device graph info.
> +
> + data-lanes:
> + description: |
> + This describes how the physical DSI data lanes are mapped
> + to the logical lanes on the given platform. The value contained in
> + index n describes what physical lane is mapped to the logical lane n
> + (DATAn, where n lies between 0 and 3). The clock lane position is fixed
> + and can't be changed. Hence, they aren't a part of the DT bindings. See
> + Documentation/devicetree/bindings/media/video-interfaces.txt for
> + more info on the data-lanes property.
> +
> + For example:
> + data-lanes = <3 0 1 2>;
> +
> + The above mapping describes that the logical data lane DATA0 is mapped
> + to the physical data lane DATA3, logical DATA1 to physical DATA0,
> + logic DATA2 to phys DATA1 and logic DATA3 to phys DATA2. There are
> + only a limited number of physical to logical mappings possible.
> + oneOf:
> + - const: <0 1 2 3>
> + - const: <1 2 3 0>
> + - const: <2 3 0 1>
> + - const: <3 0 1 2>
> + - const: <0 3 2 1>
> + - const: <1 0 3 2>
> + - const: <2 1 0 3>
> + - const: <3 2 1 0>
> + maxItems: 1
> +
> + port at 1:
> + type: object
> + description: |
> + Output endpoints of the controller.
> + properties:
> + reg:
> + const: 1
> +
> + endpoint:
> + type: object
> + properties:
> + remote-endpoint: true
> + data-lanes:
> + maxItems: 1
> +
> +...
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml
> new file mode 100644
> index 0000000..e20a7fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml
> @@ -0,0 +1,115 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-controller-sc7180.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI controller dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI controller for SC7180 target.
> +
> +allOf:
> + - $ref: dsi-common-controller.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,mdss-dsi-ctrl
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: dsi_ctrl
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + items:
> + - const: byte
> + - const: byte_intf
> + - const: pixel
> + - const: core
> + - const: iface
> + - const: bus
> +
> + phys:
> + maxItems: 1
> +
> + phy-names:
> + const: dsi
> +
> + ports: true
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - interrupt-parent
> + - interrupts
> + - clocks
> + - clock-names
> + - phys
> + - phy-names
> + - ports
> +
> +additionalProperties: false
This means none of the other properties listed in
dsi-common-controller.yaml apply here. Is that what you wanted?
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> +
> + dsi0: dsi at ae94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0 0x0ae94000 0 0x400>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> + <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&gcc GCC_DISP_HF_AXI_CLK>;
> +
> + clock-names = "byte",
> + "byte_intf",
> + "pixel",
> + "core",
> + "iface",
> + "bus";
> +
> + phys = <&dsi_phy>;
> + phy-names = "dsi";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port at 0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&dpu_intf1_out>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml
> new file mode 100644
> index 0000000..3d4771e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml
> @@ -0,0 +1,115 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-controller-sdm845.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI controller dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI controller for SDM845 target.
> +
> +allOf:
> + - $ref: dsi-common-controller.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,mdss-dsi-ctrl
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: dsi_ctrl
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + items:
> + - const: byte
> + - const: byte_intf
> + - const: pixel
> + - const: core
> + - const: iface
> + - const: bus
> +
> + phys:
> + maxItems: 1
> +
> + phy-names:
> + const: dsi
> +
> + ports: true
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - interrupt-parent
If the parent node is the MDSS, then this isn't actually required. A
parent node with 'interrupt-controller' is the default interrupt parent.
> + - interrupts
> + - clocks
> + - clock-names
> + - phys
> + - phy-names
> + - ports
> +
> +additionalProperties: false
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> +
> + dsi0: dsi at ae94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0 0x0ae94000 0 0x400>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> + <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_AXI_CLK>;
> + clock-names = "byte",
> + "byte_intf",
> + "pixel",
> + "core",
> + "iface",
> + "bus";
> +
> + phys = <&dsi0_phy>;
> + phy-names = "dsi";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&dpu_intf1_out>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml
> new file mode 100644
> index 0000000..1525cc0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml
> @@ -0,0 +1,79 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-phy-sc7180.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI PHY dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI PHY for SC7180 target.
> +
> +allOf:
> + - $ref: dsi-phy.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,dsi-phy-10nm
Same compatible as dsi-phy-sdm845? If there's differences, then should
be a different compatible.
> +
> + reg:
> + maxItems: 3
> +
> + reg-names:
> + maxItems: 3
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + items:
> + - const: iface
> + - const: ref
> +
> + "#clock-cells":
> + const: 1
> +
> + "#phy-cells":
> + const: 0
> +
> + vdds-supply:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> + - vdds-supply
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,rpmh.h>
> +
> + dsi_phy: dsi-phy at ae94400 {
> + compatible = "qcom,dsi-phy-10nm";
> + reg = <0 0x0ae94400 0 0x200>,
> + <0 0x0ae94600 0 0x280>,
> + <0 0x0ae94a00 0 0x1e0>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + vdds-supply = <&vdda_mipi_dsi0_pll>;
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml
> new file mode 100644
> index 0000000..3c60435
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml
> @@ -0,0 +1,81 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-phy-sdm845.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI PHY dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI PHY for SDM845 target.
> +
> +allOf:
> + - $ref: dsi-phy.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,dsi-phy-10nm
What about qcom,dsi-phy-10nm-8998?
> +
> + reg:
> + maxItems: 3
> +
> + reg-names:
> + maxItems: 3
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + items:
> + - const: iface
> + - const: ref
> +
> + "#clock-cells":
> + const: 1
> +
> + "#phy-cells":
> + const: 0
> +
> + vdds-supply:
> + maxItems: 1
*-supply is not a array, so 'maxItems' is not appropriate.
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> + - vdds-supply
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,rpmh.h>
> +
> + dsi0_phy: dsi-phy at ae94400 {
> + compatible = "qcom,dsi-phy-10nm";
> + reg = <0 0x0ae94400 0 0x200>,
> + <0 0x0ae94600 0 0x280>,
> + <0 0x0ae94a00 0 0x1e0>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + vdds-supply = <&vdda_mipi_dsi0_pll>;
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> +
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy.yaml
> new file mode 100644
> index 0000000..5aa60be
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy.yaml
> @@ -0,0 +1,79 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI PHY dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Common Device tree bindings for DSI PHY.
> +
> +properties:
> + compatible:
> + oneOf:
> + - const: qcom,dsi-phy-28nm-hpm
> + - const: qcom,dsi-phy-28nm-lp
> + - const: qcom,dsi-phy-20nm
> + - const: qcom,dsi-phy-28nm-8960
> + - const: qcom,dsi-phy-14nm
> + - const: qcom,dsi-phy-10nm
> + - const: qcom,dsi-phy-10nm-8998
> +
> + reg-names:
> + description: Name of register regions.
> + oneOf:
> + - description: |
> + Following regions are required for DSI 28nm HPM/LP/8960 PHYs and
> + 20nm PHY.
> + items:
> + - const: dsi_pll
> + - const: dsi_phy
> + - const: dsi_phy_regulator
> +
> + - description: |
> + Following regions are required for DSI 14nm and 10nm PHYs:
> + items:
> + - const: dsi_phy
> + - const: dsi_phy_lane
> + - const: dsi_pll
This should be more precise as to which clause goes with specific
compatibles. Probably the schema should be split between these 2
families.
> +
> + clock-cells:
> + description: |
> + The DSI PHY block acts as a clock provider, creating
> + 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
> + const: 1
> +
> + power-domains:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + description: |
> + The following clocks are required.
> + items:
> + - const: iface
> + - const: ref
> +
> + vdds-supply:
> + description: |
> + Phandle to vdds regulator device node. Required for 10nm PHY.
> +
> + qcom,dsi-phy-regulator-ldo-mode:
> + type: boolean
> + description: |
> + Boolean value indicating if the LDO mode PHY regulator is wanted (optional).
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt
> deleted file mode 100644
> index af95586..0000000
> --- a/Documentation/devicetree/bindings/display/msm/dsi.txt
> +++ /dev/null
> @@ -1,246 +0,0 @@
> -Qualcomm Technologies Inc. adreno/snapdragon DSI output
> -
> -DSI Controller:
> -Required properties:
> -- compatible:
> - * "qcom,mdss-dsi-ctrl"
> -- reg: Physical base address and length of the registers of controller
> -- reg-names: The names of register regions. The following regions are required:
> - * "dsi_ctrl"
> -- interrupts: The interrupt signal from the DSI block.
> -- power-domains: Should be <&mmcc MDSS_GDSC>.
> -- clocks: Phandles to device clocks.
> -- clock-names: the following clocks are required:
> - * "mdp_core"
> - * "iface"
> - * "bus"
> - * "core_mmss"
> - * "byte"
> - * "pixel"
> - * "core"
> - For DSIv2, we need an additional clock:
> - * "src"
> - For DSI6G v2.0 onwards, we need also need the clock:
> - * "byte_intf"
> -- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
> -- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
> - by a DSI PHY block. See [1] for details on clock bindings.
> -- vdd-supply: phandle to vdd regulator device node
> -- vddio-supply: phandle to vdd-io regulator device node
> -- vdda-supply: phandle to vdda regulator device node
> -- phys: phandle to DSI PHY device node
> -- phy-names: the name of the corresponding PHY device
> -- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
> -- ports: Contains 2 DSI controller ports as child nodes. Each port contains
> - an endpoint subnode as defined in [2] and [3].
> -
> -Optional properties:
> -- panel at 0: Node of panel connected to this DSI controller.
> - See files in [4] for each supported panel.
> -- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
> - driving a panel which needs 2 DSI links.
> -- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
> - the master link of the 2-DSI panel.
> -- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
> - driving a 2-DSI panel whose 2 links need receive command simultaneously.
> -- pinctrl-names: the pin control state names; should contain "default"
> -- pinctrl-0: the default pinctrl state (active)
> -- pinctrl-n: the "sleep" pinctrl state
> -- ports: contains DSI controller input and output ports as children, each
> - containing one endpoint subnode.
> -
> - DSI Endpoint properties:
> - - remote-endpoint: For port at 0, set to phandle of the connected panel/bridge's
> - input endpoint. For port at 1, set to the MDP interface output. See [2] for
> - device graph info.
> -
> - - data-lanes: this describes how the physical DSI data lanes are mapped
> - to the logical lanes on the given platform. The value contained in
> - index n describes what physical lane is mapped to the logical lane n
> - (DATAn, where n lies between 0 and 3). The clock lane position is fixed
> - and can't be changed. Hence, they aren't a part of the DT bindings. See
> - [3] for more info on the data-lanes property.
> -
> - For example:
> -
> - data-lanes = <3 0 1 2>;
> -
> - The above mapping describes that the logical data lane DATA0 is mapped to
> - the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
> - to phys DATA1 and logic DATA3 to phys DATA2.
> -
> - There are only a limited number of physical to logical mappings possible:
> - <0 1 2 3>
> - <1 2 3 0>
> - <2 3 0 1>
> - <3 0 1 2>
> - <0 3 2 1>
> - <1 0 3 2>
> - <2 1 0 3>
> - <3 2 1 0>
> -
> -DSI PHY:
> -Required properties:
> -- compatible: Could be the following
> - * "qcom,dsi-phy-28nm-hpm"
> - * "qcom,dsi-phy-28nm-lp"
> - * "qcom,dsi-phy-20nm"
> - * "qcom,dsi-phy-28nm-8960"
> - * "qcom,dsi-phy-14nm"
> - * "qcom,dsi-phy-10nm"
> - * "qcom,dsi-phy-10nm-8998"
> -- reg: Physical base address and length of the registers of PLL, PHY. Some
> - revisions require the PHY regulator base address, whereas others require the
> - PHY lane base address. See below for each PHY revision.
> -- reg-names: The names of register regions. The following regions are required:
> - For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
> - * "dsi_pll"
> - * "dsi_phy"
> - * "dsi_phy_regulator"
> - For DSI 14nm and 10nm PHYs:
> - * "dsi_pll"
> - * "dsi_phy"
> - * "dsi_phy_lane"
> -- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
> - 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
> -- power-domains: Should be <&mmcc MDSS_GDSC>.
> -- clocks: Phandles to device clocks. See [1] for details on clock bindings.
> -- clock-names: the following clocks are required:
> - * "iface"
> - * "ref" (only required for new DTS files/entries)
> - For 28nm HPM/LP, 28nm 8960 PHYs:
> -- vddio-supply: phandle to vdd-io regulator device node
> - For 20nm PHY:
> -- vddio-supply: phandle to vdd-io regulator device node
> -- vcca-supply: phandle to vcca regulator device node
> - For 14nm PHY:
> -- vcca-supply: phandle to vcca regulator device node
Seems you dropped all these supplies.
> - For 10nm PHY:
> -- vdds-supply: phandle to vdds regulator device node
> -
> -Optional properties:
> -- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
> - regulator is wanted.
> -- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
> - panels in microseconds. Driver uses this number to adjust
> - the clock rate according to the expected transfer time.
> - Increasing this value would slow down the mdp processing
> - and can result in slower performance.
> - Decreasing this value can speed up the mdp processing,
> - but this can also impact power consumption.
> - As a rule this time should not be higher than the time
> - that would be expected with the processing at the
> - dsi link rate since anyways this would be the maximum
> - transfer time that could be achieved.
> - If ping pong split is enabled, this time should not be higher
> - than two times the dsi link rate time.
> - If the property is not specified, then the default value is 14000 us.
This property got dropped.
> -
> -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
> -[2] Documentation/devicetree/bindings/graph.txt
> -[3] Documentation/devicetree/bindings/media/video-interfaces.txt
> -[4] Documentation/devicetree/bindings/display/panel/
> -
> -Example:
> - dsi0: dsi at fd922800 {
> - compatible = "qcom,mdss-dsi-ctrl";
> - qcom,dsi-host-index = <0>;
> - interrupt-parent = <&mdp>;
> - interrupts = <4 0>;
> - reg-names = "dsi_ctrl";
> - reg = <0xfd922800 0x200>;
> - power-domains = <&mmcc MDSS_GDSC>;
> - clock-names =
> - "bus",
> - "byte",
> - "core",
> - "core_mmss",
> - "iface",
> - "mdp_core",
> - "pixel";
> - clocks =
> - <&mmcc MDSS_AXI_CLK>,
> - <&mmcc MDSS_BYTE0_CLK>,
> - <&mmcc MDSS_ESC0_CLK>,
> - <&mmcc MMSS_MISC_AHB_CLK>,
> - <&mmcc MDSS_AHB_CLK>,
> - <&mmcc MDSS_MDP_CLK>,
> - <&mmcc MDSS_PCLK0_CLK>;
> -
> - assigned-clocks =
> - <&mmcc BYTE0_CLK_SRC>,
> - <&mmcc PCLK0_CLK_SRC>;
> - assigned-clock-parents =
> - <&dsi_phy0 0>,
> - <&dsi_phy0 1>;
> -
> - vdda-supply = <&pma8084_l2>;
> - vdd-supply = <&pma8084_l22>;
> - vddio-supply = <&pma8084_l12>;
> -
> - phys = <&dsi_phy0>;
> - phy-names ="dsi-phy";
> -
> - qcom,dual-dsi-mode;
> - qcom,master-dsi;
> - qcom,sync-dual-dsi;
> -
> - qcom,mdss-mdp-transfer-time-us = <12000>;
> -
> - pinctrl-names = "default", "sleep";
> - pinctrl-0 = <&dsi_active>;
> - pinctrl-1 = <&dsi_suspend>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port at 0 {
> - reg = <0>;
> - dsi0_in: endpoint {
> - remote-endpoint = <&mdp_intf1_out>;
> - };
> - };
> -
> - port at 1 {
> - reg = <1>;
> - dsi0_out: endpoint {
> - remote-endpoint = <&panel_in>;
> - data-lanes = <0 1 2 3>;
> - };
> - };
> - };
> -
> - panel: panel at 0 {
> - compatible = "sharp,lq101r1sx01";
> - reg = <0>;
> - link2 = <&secondary>;
> -
> - power-supply = <...>;
> - backlight = <...>;
> -
> - port {
> - panel_in: endpoint {
> - remote-endpoint = <&dsi0_out>;
> - };
> - };
> - };
> - };
> -
> - dsi_phy0: dsi-phy at fd922a00 {
> - compatible = "qcom,dsi-phy-28nm-hpm";
> - qcom,dsi-phy-index = <0>;
> - reg-names =
> - "dsi_pll",
> - "dsi_phy",
> - "dsi_phy_regulator";
> - reg = <0xfd922a00 0xd4>,
> - <0xfd922b00 0x2b0>,
> - <0xfd922d80 0x7b>;
> - clock-names = "iface";
> - clocks = <&mmcc MDSS_AHB_CLK>;
> - #clock-cells = <1>;
> - vddio-supply = <&pma8084_l12>;
> -
> - qcom,dsi-phy-regulator-ldo-mode;
> - };
> --
> 1.9.1
>
More information about the Freedreno
mailing list