[Freedreno] [PATCH] drm/msm/dsi: save PLL registers across first PHY reset

[Dmitry Baryshkov]

Hello,

On 07/10/2020 03:10, benl-kernelpatches at squareup.com wrote:
> From: Benjamin Li <benl at squareup.com>
> 
> Take advantage of previously-added support for persisting PLL
> registers across DSI PHY disable/enable cycles (see 328e1a6
> 'drm/msm/dsi: Save/Restore PLL status across PHY reset') to
> support persisting across the very first DSI PHY enable at
> boot.

Interesting enough, this breaks exactly on 8016. On DB410c with latest 
bootloader and w/o splash screen this patch causes boot freeze. Without 
this patch the board would successfully boot with display routed to HDMI.

> The bootloader may have left the PLL registers in a non-default
> state. For example, for dsi_pll_28nm.c on 8x16/8x39, the byte
> clock mux's power-on reset configuration is to bypass DIV1, but
> depending on bandwidth requirements[1] the bootloader may have
> set the DIV1 path.
> 
> When the byte clock mux is registered with the generic clock
> framework at probe time, the framework reads & caches the value
> of the mux bit field (the initial clock parent). After PHY enable,
> when clk_set_rate is called on the byte clock, the framework
> assumes there is no need to reparent, and doesn't re-write the
> mux bit field. But PHY enable resets PLL registers, so the mux
> bit field actually silently reverted to the DIV1 bypass path.
> This causes the byte clock to be off by a factor of e.g. 2 for
> our tested WXGA panel.
> 
> The above issue manifests as the display not working and a
> constant stream of FIFO/LP0 contention errors.
> 
> [1] The specific requirement for triggering the DIV1 path (and
> thus this issue) on 28nm is a panel with pixel clock <116.7MHz
> (one-third the minimum VCO setting). FHD/1080p (~145MHz) is fine,
> WXGA/1280x800 (~75MHz) is not.
> 
> Signed-off-by: Benjamin Li <benl at squareup.com>
> ---
>   drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 16 ++++++++++++++++
>   1 file changed, 16 insertions(+)
> 
> diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> index 009f5b843dd1..139b4a5aaf86 100644
> --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
> @@ -621,6 +621,22 @@ static int dsi_phy_driver_probe(struct platform_device *pdev)
>   		phy->pll = NULL;
>   	}
>   
> +	/*
> +	 * As explained in msm_dsi_phy_enable, resetting the DSI PHY (as done
> +	 * in dsi_mgr_phy_enable) silently changes its PLL registers to power-on
> +	 * defaults, but the generic clock framework manages and caches several
> +	 * of the PLL registers. It initializes these caches at registration
> +	 * time via register read.
> +	 *
> +	 * As a result, we need to save DSI PLL registers once at probe in order
> +	 * for the first call to msm_dsi_phy_enable to successfully bring PLL
> +	 * registers back in line with what the generic clock framework expects.
> +	 *
> +	 * Subsequent PLL restores during msm_dsi_phy_enable will always be
> +	 * paired with PLL saves in msm_dsi_phy_disable.
> +	 */
> +	msm_dsi_pll_save_state(phy->pll);
> +
>   	dsi_phy_disable_resource(phy);
>   
>   	platform_set_drvdata(pdev, phy);
> 


-- 
With best wishes
Dmitry