[Freedreno] [PATCH v1 4/4] arm64: dts: qcom: sc7280: add edp display dt nodes
Stephen Boyd
swboyd at chromium.org
Wed Aug 18 20:03:10 UTC 2021
Quoting Krishna Manikandan (2021-08-18 03:27:04)
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index aadf55d..5be318e 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -1412,7 +1412,7 @@
> reg = <0 0xaf00000 0 0x20000>;
> clocks = <&rpmhcc RPMH_CXO_CLK>,
> <&gcc GCC_DISP_GPLL0_CLK_SRC>,
> - <0>, <0>, <0>, <0>, <0>, <0>;
> + <0>, <0>, <0>, <0>, <&edp_phy 0>, <&edp_phy 1>;
> clock-names = "bi_tcxo", "gcc_disp_gpll0_clk",
> "dsi0_phy_pll_out_byteclk",
> "dsi0_phy_pll_out_dsiclk",
> @@ -1493,6 +1493,12 @@
> remote-endpoint = <&dsi0_in>;
> };
> };
Newline here please.
> + port at 1 {
> + reg = <1>;
> + dpu_intf5_out: endpoint {
> + remote-endpoint = <&edp_in>;
> + };
> + };
> };
>
> mdp_opp_table: mdp-opp-table {
> @@ -1608,6 +1614,101 @@
>
> status = "disabled";
> };
> +
> + msm_edp: edp at aea0000 {
> + status = "disabled";
Please pick a place to put status disabled. I don't know what qcom
maintainers want, but please be consistent.
> + compatible = "qcom,sc7280-edp";
> + reg = <0 0xaea0000 0 0x200>,
> + <0 0xaea0200 0 0x200>,
> + <0 0xaea0400 0 0xc00>,
> + <0 0xaea1000 0 0x400>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <14 IRQ_TYPE_NONE>;
Drop flags.
> +
> + clocks = <&rpmhcc RPMH_CXO_CLK>,
> + <&gcc GCC_EDP_CLKREF_EN>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
> + <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
> + <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
> + clock-names = "core_xo", "core_ref",
> + "core_iface", "core_aux", "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
One line per string please.
> + #clock-cells = <1>;
> + assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
> + <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
> + assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>;
> +
> + phys = <&edp_phy>;
> + phy-names = "dp";
> +
> + vdda-1p2-supply = <&vreg_l6b_1p2>;
> + vdda-0p9-supply = <&vreg_l10c_0p8>;
Can this be done here? Probably needs to move to the board dts/dtsi
file.
> + operating-points-v2 = <&edp_opp_table>;
> + power-domains = <&rpmhpd SC7280_CX>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_hot_plug_det>, <&edp_panel_power_on>;
> +
> + panel-bklt-gpio = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
> + panel-pwm-gpio = <&pm8350c_gpios 8 GPIO_ACTIVE_HIGH>;
Please no panel-bklt-gpio and panel-pwm-gpio properties.
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port at 0 {
> + reg = <0>;
> + edp_in: endpoint {
> + remote-endpoint = <&dpu_intf5_out>;
> + };
> + };
> + };
> +
> + edp_opp_table: edp-opp-table {
edp_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> +
> + edp_phy: phy at aec2000 {
Good job on using phy!
> + status = "disabled";
> + compatible = "qcom,sc7280-edp-phy";
> + reg = <0 0xaec2a00 0 0x19c>,
> + <0 0xaec2200 0 0xa0>,
> + <0 0xaec2600 0 0xa0>,
> + <0 0xaec2000 0 0x1c0>;
> +
> + clocks = <&rpmhcc RPMH_CXO_CLK>,
> + <&gcc GCC_EDP_CLKREF_EN>;
> + clock-names = "aux", "cfg_ahb";
> +
> + vdda-pll-supply = <&vreg_l6b_1p2>;
> + vdda-phy-supply = <&vreg_l10c_0p8>;
Again, still question the ability to put this here vs. in IDP file.
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + };
> };
>
> pdc: interrupt-controller at b220000 {
> @@ -1704,6 +1805,30 @@
> function = "qup13";
> };
>
> + edp_hot_plug_det: edp-hot-plug-det {
> + pinmux {
> + pins = "gpio60";
> + function = "edp_hot";
> + };
> + pinconf {
> + pins = "gpio60";
> + bias-pull-down;
> + input-enable;
> + };
Move pinconf stuff to board file (and combine nodes as mka stated).
> + };
> +
> + edp_panel_power_on: edp-panel-power-on {
> + pinmux {
> + pins = "gpio80";
> + function = "gpio";
> + };
> + pinconf {
> + pins = "gpio80";
> + bias-disable;
> + output-high;
> + };
> + };
> +
> sdc1_on: sdc1-on {
> clk {
> pins = "sdc1_clk";
> --
> 2.7.4
>
More information about the Freedreno
mailing list