[Freedreno] [RFC] drm/msm/disp/dpu1: add support for inline rotation in dpu driver
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Sun Jul 4 11:20:32 UTC 2021
On 03/07/2021 14:32, Kalyan Thota wrote:
> Add inline rotation support in dpu driver. This change adds
> rotation config for SC7280 target.
>
> Change-Id: I15861dc03422274ffd823fc0fc2c1e47909bb22c
> Signed-off-by: Kalyan Thota <kalyan_t at codeaurora.org>
> ---
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 47 +++++++++----
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 20 ++++++
> drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 93 ++++++++++++++++++++------
> drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h | 2 +
> 4 files changed, 128 insertions(+), 34 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> index d01c4c9..45e4e56 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> @@ -25,6 +25,9 @@
> #define VIG_SM8250_MASK \
> (VIG_MASK | BIT(DPU_SSPP_QOS_8LVL) | BIT(DPU_SSPP_SCALER_QSEED3LITE))
>
> +#define VIG_SC7280_MASK \
> + (VIG_SC7180_MASK | BIT(DPU_SSPP_INLINE_ROTATION))
> +
> #define DMA_SDM845_MASK \
> (BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) | BIT(DPU_SSPP_QOS_8LVL) |\
> BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
> @@ -102,6 +105,8 @@
> #define MAX_DOWNSCALE_RATIO 4
> #define SSPP_UNITY_SCALE 1
>
> +#define INLINE_ROTATOR_V2 2
> +
> #define STRCAT(X, Y) (X Y)
>
> static const uint32_t plane_formats[] = {
> @@ -177,6 +182,11 @@ static const uint32_t plane_formats_yuv[] = {
> DRM_FORMAT_YVU420,
> };
>
> +static const uint32_t rotation_formats[] = {
> + DRM_FORMAT_NV12,
> + /* TODO add formats after validation */
> +};
> +
> /*************************************************************
> * DPU sub blocks config
> *************************************************************/
> @@ -465,7 +475,16 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>
> /* SSPP common configuration */
>
> -#define _VIG_SBLK(num, sdma_pri, qseed_ver) \
> +static const struct dpu_rotation_cfg dpu_rot_cfg = {
> + .version = INLINE_ROTATOR_V2,
> + .rot_maxdwnscale_ratio_num = 1,
> + .rot_maxdwnscale_ratio_dem = 1,
> + .rot_maxheight = 1088,
> + .rot_num_formats = ARRAY_SIZE(rotation_formats),
> + .rot_format_list = rotation_formats,
> +};
> +
> +#define _VIG_SBLK(num, sdma_pri, qseed_ver, rot_cfg) \
> { \
> .maxdwnscale = MAX_DOWNSCALE_RATIO, \
> .maxupscale = MAX_UPSCALE_RATIO, \
> @@ -482,6 +501,7 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
> .num_formats = ARRAY_SIZE(plane_formats_yuv), \
> .virt_format_list = plane_formats, \
> .virt_num_formats = ARRAY_SIZE(plane_formats), \
> + .rotation_cfg = rot_cfg, \
> }
>
> #define _DMA_SBLK(num, sdma_pri) \
> @@ -498,13 +518,13 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
> }
>
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_0 =
> - _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3, 0);
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_1 =
> - _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3, 0);
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_2 =
> - _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3, 0);
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_3 =
> - _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3, 0);
>
> static const struct dpu_sspp_sub_blks sdm845_dma_sblk_0 = _DMA_SBLK("8", 1);
> static const struct dpu_sspp_sub_blks sdm845_dma_sblk_1 = _DMA_SBLK("9", 2);
> @@ -543,7 +563,10 @@ static const struct dpu_sspp_cfg sdm845_sspp[] = {
> };
>
> static const struct dpu_sspp_sub_blks sc7180_vig_sblk_0 =
> - _VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4);
> + _VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, 0);
> +
> +static const struct dpu_sspp_sub_blks sc7280_vig_sblk_0 =
> + _VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, &dpu_rot_cfg);
>
> static const struct dpu_sspp_cfg sc7180_sspp[] = {
> SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> @@ -557,13 +580,13 @@ static const struct dpu_sspp_cfg sc7180_sspp[] = {
> };
>
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_0 =
> - _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE, 0);
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_1 =
> - _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE, 0);
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_2 =
> - _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE, 0);
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_3 =
> - _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE, 0);
>
> static const struct dpu_sspp_cfg sm8250_sspp[] = {
> SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SM8250_MASK,
> @@ -585,8 +608,8 @@ static const struct dpu_sspp_cfg sm8250_sspp[] = {
> };
>
> static const struct dpu_sspp_cfg sc7280_sspp[] = {
> - SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> - sc7180_vig_sblk_0, 0, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> + SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7280_MASK,
> + sc7280_vig_sblk_0, 0, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000, DMA_SDM845_MASK,
> sdm845_dma_sblk_0, 1, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
> SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000, DMA_CURSOR_SDM845_MASK,
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> index d2a945a..8421001 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> @@ -129,6 +129,7 @@ enum {
> DPU_SSPP_TS_PREFILL,
> DPU_SSPP_TS_PREFILL_REC1,
> DPU_SSPP_CDP,
> + DPU_SSPP_INLINE_ROTATION,
> DPU_SSPP_MAX
> };
>
> @@ -309,6 +310,24 @@ struct dpu_qos_lut_tbl {
> };
>
> /**
> + * struct dpu_rotation_cfg - define inline rotation config
> + * @version: Inline rotation version
> + * @rot_maxdwnscale_ratio_num: max downscale ratio for rotation numerator
> + * @rot_maxdwnscale_ratio_dem: max downscale ratio for denominator
> + * @rot_maxheight: max pre rotated height allowed for rotation
> + * @rot_num_formats: count of the formats
> + * @rot_format_list: list of supported rotator formats
> + */
> +struct dpu_rotation_cfg {
> + u32 version;
> + u32 rot_maxdwnscale_ratio_num;
> + u32 rot_maxdwnscale_ratio_dem;
> + u32 rot_maxheight;
> + u32 rot_num_formats;
> + const u32 *rot_format_list;
> +};
> +
> +/**
> * struct dpu_caps - define DPU capabilities
> * @max_mixer_width max layer mixer line width support.
> * @max_mixer_blendstages max layer mixer blend stages or
> @@ -384,6 +403,7 @@ struct dpu_sspp_sub_blks {
> u32 num_formats;
> const u32 *virt_format_list;
> u32 virt_num_formats;
> + const struct dpu_rotation_cfg *rotation_cfg;
> };
>
> /**
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> index ec4a6f0..0daee63 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> @@ -539,16 +539,28 @@ static void _dpu_plane_set_scanout(struct drm_plane *plane,
>
> static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
> struct dpu_plane_state *pstate,
> - uint32_t src_w, uint32_t src_h, uint32_t dst_w, uint32_t dst_h,
> struct dpu_hw_scaler3_cfg *scale_cfg,
> const struct dpu_format *fmt,
> uint32_t chroma_subsmpl_h, uint32_t chroma_subsmpl_v)
> {
> uint32_t i;
> + bool inline_rotation = (pstate->rotation & DRM_MODE_ROTATE_90);
> + uint32_t src_w = drm_rect_width(&pdpu->pipe_cfg.src_rect);
> + uint32_t src_h = drm_rect_height(&pdpu->pipe_cfg.src_rect);
> + uint32_t dst_w = drm_rect_width(&pdpu->pipe_cfg.dst_rect);
> + uint32_t dst_h = drm_rect_height(&pdpu->pipe_cfg.dst_rect);
>
> memset(scale_cfg, 0, sizeof(*scale_cfg));
> memset(&pstate->pixel_ext, 0, sizeof(struct dpu_hw_pixel_ext));
>
> + /*
> + * For inline rotation cases, scaler config is post-rotation,
> + * so swap the dimensions here. However, pixel extension will
> + * need pre-rotation settings.
> + */
> + if (inline_rotation)
> + swap(src_w, src_h);
> +
> scale_cfg->phase_step_x[DPU_SSPP_COMP_0] =
> mult_frac((1 << PHASE_STEP_SHIFT), src_w, dst_w);
> scale_cfg->phase_step_y[DPU_SSPP_COMP_0] =
> @@ -587,10 +599,10 @@ static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
> scale_cfg->preload_y[i] = DPU_QSEED3_DEFAULT_PRELOAD_V;
> }
>
> - pstate->pixel_ext.num_ext_pxls_top[i] =
> - scale_cfg->src_height[i];
> - pstate->pixel_ext.num_ext_pxls_left[i] =
> - scale_cfg->src_width[i];
> + pstate->pixel_ext.num_ext_pxls_top[i] = inline_rotation ?
> + scale_cfg->src_width[i] : scale_cfg->src_height[i];
> + pstate->pixel_ext.num_ext_pxls_left[i] = inline_rotation ?
> + scale_cfg->src_height[i] : scale_cfg->src_width[i];
> }
> if (!(DPU_FORMAT_IS_YUV(fmt)) && (src_h == dst_h)
> && (src_w == dst_w))
> @@ -662,10 +674,6 @@ static void _dpu_plane_setup_scaler(struct dpu_plane *pdpu,
> /* don't chroma subsample if decimating */
> /* update scaler. calculate default config for QSEED3 */
> _dpu_plane_setup_scaler3(pdpu, pstate,
> - drm_rect_width(&pdpu->pipe_cfg.src_rect),
> - drm_rect_height(&pdpu->pipe_cfg.src_rect),
> - drm_rect_width(&pdpu->pipe_cfg.dst_rect),
> - drm_rect_height(&pdpu->pipe_cfg.dst_rect),
> &pstate->scaler3_cfg, fmt,
> info->hsub, info->vsub);
> }
> @@ -959,6 +967,7 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
> const struct dpu_format *fmt;
> struct drm_rect src, dst, fb_rect = { 0 };
> uint32_t min_src_size, max_linewidth;
> + unsigned int rotation;
>
> if (new_plane_state->crtc)
> crtc_state = drm_atomic_get_new_crtc_state(state,
> @@ -1028,6 +1037,48 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
> return -E2BIG;
> }
>
> + rotation = drm_rotation_simplify(new_plane_state->rotation,
> + DRM_MODE_ROTATE_0 |
> + DRM_MODE_ROTATE_90 |
> + DRM_MODE_REFLECT_X |
> + DRM_MODE_REFLECT_Y);
> +
> + if (rotation & DRM_MODE_ROTATE_90) {
> + struct msm_drm_private *priv = plane->dev->dev_private;
> + struct dpu_kms *dpu_kms;
> + const struct msm_format *msm_fmt;
> + const struct dpu_format *fmt;
> + bool found = false;
> + u32 i, num_formats;
> + const u32 *supported_formats;
> +
> + if (src.y2 > pdpu->pipe_sblk->rotation_cfg->rot_maxheight) {
Another note: drm_rect_width(&src) rather than src.y2 here.
> + DPU_DEBUG_PLANE(pdpu,
> + "invalid height for inline rot:%d max:%d\n",
> + src.y2, pdpu->pipe_sblk->rotation_cfg->rot_maxheight);
> + return -EINVAL;
> + }
> +
> + /* check for valid formats supported by inline rotation */
> + dpu_kms = to_dpu_kms(priv->kms);
> + msm_fmt = msm_framebuffer_format(new_plane_state->fb);
> + fmt = to_dpu_format(msm_fmt);
> + supported_formats = pdpu->pipe_sblk->rotation_cfg->rot_format_list;
> + num_formats = pdpu->pipe_sblk->rotation_cfg->rot_num_formats;
> +
> + for (i = 0; i < num_formats; i++) {
> + if (fmt->base.pixel_format == supported_formats[i] &&
> + fmt->fetch_mode == DPU_FETCH_UBWC)
> + found = true;
> + }
> +
> + if (!found || !num_formats) {
> + DPU_DEBUG_PLANE(pdpu,
> + "supported_format not found num:%d\n", num_formats);
> + return -EINVAL;
> + }
> + }
> + pstate->rotation = rotation;
> pstate->needs_qos_remap = drm_atomic_crtc_needs_modeset(crtc_state);
>
> return 0;
> @@ -1153,21 +1204,18 @@ static void dpu_plane_sspp_atomic_update(struct drm_plane *plane)
> pstate->multirect_mode);
>
> if (pdpu->pipe_hw->ops.setup_format) {
> - unsigned int rotation;
>
> src_flags = 0x0;
>
> - rotation = drm_rotation_simplify(state->rotation,
> - DRM_MODE_ROTATE_0 |
> - DRM_MODE_REFLECT_X |
> - DRM_MODE_REFLECT_Y);
> -
> - if (rotation & DRM_MODE_REFLECT_X)
> + if (pstate->rotation & DRM_MODE_REFLECT_X)
> src_flags |= DPU_SSPP_FLIP_LR;
>
> - if (rotation & DRM_MODE_REFLECT_Y)
> + if (pstate->rotation & DRM_MODE_REFLECT_Y)
> src_flags |= DPU_SSPP_FLIP_UD;
>
> + if (pstate->rotation & DRM_MODE_ROTATE_90)
> + src_flags |= DPU_SSPP_ROT_90;
> +
> /* update format */
> pdpu->pipe_hw->ops.setup_format(pdpu->pipe_hw, fmt, src_flags,
> pstate->multirect_index);
> @@ -1578,6 +1626,8 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
> int zpos_max = DPU_ZPOS_MAX;
> uint32_t num_formats;
> int ret = -EINVAL;
> + unsigned int supported_rotations = DRM_MODE_ROTATE_0 |
> + DRM_MODE_ROTATE_180 | DRM_MODE_REFLECT_X | DRM_MODE_REFLECT_Y;
>
> /* create and zero local structure */
> pdpu = kzalloc(sizeof(*pdpu), GFP_KERNEL);
> @@ -1647,12 +1697,11 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
> if (ret)
> DPU_ERROR("failed to install zpos property, rc = %d\n", ret);
>
> + if (pdpu->features & BIT(DPU_SSPP_INLINE_ROTATION))
> + supported_rotations |= DRM_MODE_ROTATE_90;
> +
> drm_plane_create_rotation_property(plane,
> - DRM_MODE_ROTATE_0,
> - DRM_MODE_ROTATE_0 |
> - DRM_MODE_ROTATE_180 |
> - DRM_MODE_REFLECT_X |
> - DRM_MODE_REFLECT_Y);
> + DRM_MODE_ROTATE_0, supported_rotations);
>
> drm_plane_enable_fb_damage_clips(plane);
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> index 34e03ac..16ec8dc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> @@ -28,6 +28,7 @@
> * @cdp_cfg: CDP configuration
> * @plane_fetch_bw: calculated BW per plane
> * @plane_clk: calculated clk per plane
> + * @rotation: simplified drm rotation hint
> */
> struct dpu_plane_state {
> struct drm_plane_state base;
> @@ -45,6 +46,7 @@ struct dpu_plane_state {
> struct dpu_hw_pipe_cdp_cfg cdp_cfg;
> u64 plane_fetch_bw;
> u64 plane_clk;
> + unsigned int rotation;
> };
>
> /**
>
--
With best wishes
Dmitry
More information about the Freedreno
mailing list