[Freedreno] [PATCH v2 11/11] dt-bindings: display/msm: move common DPU properties to dpu-common.yaml

[Dmitry Baryshkov]

On 18/07/2022 20:50, Rob Herring wrote:
> On Sun, Jul 10, 2022 at 12:00:40PM +0300, Dmitry Baryshkov wrote:
>> Move properties common to all DPU DT nodes to the dpu-common.yaml.
>>
>> Note, this removes description of individual DPU port@ nodes. However
>> such definitions add no additional value. The reg values do not
>> correspond to hardware INTF indices. The driver discovers and binds
>> these ports not paying any care for the order of these items. Thus just
>> leave the reference to graph.yaml#/properties/ports and the description.
>>
>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
>> ---
>>   .../bindings/display/msm/dpu-common.yaml      | 42 ++++++++++++++++++
>>   .../bindings/display/msm/dpu-msm8998.yaml     | 43 ++-----------------
>>   .../bindings/display/msm/dpu-qcm2290.yaml     | 39 ++---------------
>>   .../bindings/display/msm/dpu-sc7180.yaml      | 43 ++-----------------
>>   .../bindings/display/msm/dpu-sc7280.yaml      | 43 ++-----------------
>>   .../bindings/display/msm/dpu-sdm845.yaml      | 43 ++-----------------
>>   6 files changed, 62 insertions(+), 191 deletions(-)
>>   create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-common.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/display/msm/dpu-common.yaml b/Documentation/devicetree/bindings/display/msm/dpu-common.yaml
>> new file mode 100644
>> index 000000000000..14eda883e149
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/msm/dpu-common.yaml
>> @@ -0,0 +1,42 @@
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/display/msm/dpu-common.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm Display DPU dt properties (common properties)
>> +
>> +maintainers:
>> +  - Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
>> +  - Krishna Manikandan <quic_mkrishn at quicinc.com>
>> +  - Rob Clark <robdclark at gmail.com>
>> +
>> +description: |
>> +  Common properties for QCom DPU display controller.
>> +
>> +properties:
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  power-domains:
>> +    maxItems: 1
>> +
>> +  operating-points-v2: true
>> +
>> +  ports:
>> +    $ref: /schemas/graph.yaml#/properties/ports
>> +    description: |
>> +      Contains the list of output ports from DPU device. These ports
>> +      connect to interfaces that are external to the DPU hardware,
>> +      such as DSI, DP etc.
> 
>  From the last version:
> 
>> In case of MDSS all ports are output, they are connected to the external
>> interfaces (DSI, DP, HDMI, etc). The driver uses them to bind available
>> interfaces (using components framework). The reg property of the port is
>> completely ignored.
> 
> It doesn't matter what the driver does or doesn't do. Without
> describing port nodes at all, you are not validating what port nodes
> can contain. Just try adding any property under a port node. You need at
> least:
> 
> '^port@[0-N]$':
>    $ref: graph.yaml#/properties/port


Hmm, the graph.yaml already restricts the ports node to the 
ports@[0-9a-f]+$ + #address-cells/#size-cells. I don't think we have to 
add any additional restrictions/entries here. Do we?

> 
> where N is the max number of ports.
> 
> Rob

-- 
With best wishes
Dmitry