[Freedreno] [RFC] drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge
Abhinav Kumar
quic_abhinavk at quicinc.com
Mon Aug 29 18:40:29 UTC 2022
Hi Laurent
On 8/26/2022 4:55 AM, Laurent Pinchart wrote:
> Hello,
>
> On Fri, Aug 26, 2022 at 01:17:43PM +0300, Dmitry Baryshkov wrote:
>> On 22/08/2022 19:31, Dmitry Baryshkov wrote:
>>> On 09/08/2022 22:40, Laurent Pinchart wrote:
>>>> On Mon, Aug 08, 2022 at 05:35:30PM -0700, Abhinav Kumar wrote:
>>>>> adv7533 bridge tries to dynamically switch lanes based on the
>>>>> mode by detaching and attaching the mipi dsi device.
>>>>>
>>>>> This approach is incorrect because as per the DSI spec the
>>>>> number of lanes is fixed at the time of system design or initial
>>>>> configuration and may not change dynamically.
>>>>
>>>> Is that really so ? The number of lanes connected on the board is
>>>> certainlyset at design time, but a lower number of lanes can be used at
>>>> runtime. It shouldn't change dynamically while the display is on, but it
>>>> could change at mode set time.
>>>
>>> I'm not sure if I interpreted the standard correctly, but I tended to
>>> have the same interpretation as Abhinav did.
>>>
>>> Anyway, even if we allow the drivers to switch the amount of lanes, this
>>> should not happen in the form of detach()/attach() cycle. The drivers
>
> Agreed.
>
>>> use mipi_dsi_attach() as way to signal the DSI hosts that the sink
>>> device is ready. Some of DSI hosts (including MSM one) would bind
>>> components from the attach callback.
>>>
>>> If we were to support dynamically changing the amount of lanes, I would
>>> ask for additional mipi_dsi API call telling the host to switch the
>>> amount of lanes. And note that this can open the can of worms. Different
>>> hosts might have different requirements here. For example for the MSM
>>> platform the amount of lanes is programmed during bridge_pre_enable
>>> chain call, so it is possible to just set the amount of lanes following
>>> the msm_dsi_device::lanes. Other hosts might have other requirements.
>
> Conceptually, I would expect the number of effective lanes to be
> selected at mode set time, because it has to be done while the output is
> disabled. With the atomic API for bridges the .mode_set() operation is
> deprecated, so .pre_enable() sounds best, but there's a potential issue:
> the .pre_enable() operation is called from sink to source. It means that
> a DSI sink .pre_enable() operation would need to call a DSI host
> operation to set (or maybe negotiate instead of just setting a fixed
> value) the number of lanes first if it wants to control the sink through
> DCS at .pre_enable() time. We'd have to see how that fits.
>
>>> Thus said I'd suggest accepting this patch and maybe working on the
>>> API/support for the lane switching as a followup.
>
> I don't have a personal need for the ADV7533 so I won't really complain
> about any potential regression this may introduce (given that it fixes a
> deadlock maybe things are completely broken already and nothing can
> regress). I'd like to see this fixed though, doing it as a follow up is
> too often a way to avoid doing it at all :-)
>
> In any case, the commit message should be reworded to explain the
> rationale and what needs to be done. Adding a TODO or FIXME comment in
> the code would also help.
>
Yes, I have added a TODO in the code . fixed the commit text and posted
this removing the RFC tag to address this deadlock issue.
Thanks
Abhinav
>> Laurent, gracious ping for your response.
>
> Done :-)
>
>>>>> In addition this method of dynamic switch of detaching and
>>>>> attaching the mipi dsi device also results in removing
>>>>> and adding the component which is not necessary.
>>>>
>>>> Yes, that doesn't look good, and the .mode_valid() operation is
>>>> definitely not the right point where to set the number of lanes.
>>>
>>> .mode_set()?
>>>
>>>>> This approach is also prone to deadlocks. So for example, on the
>>>>> db410c whenever this path is executed with lockdep enabled,
>>>>> this results in a deadlock due to below ordering of locks.
>>>
>>> Even without the deadlock, we are pulling the whole DRM device from
>>> beneath the DSI panel by unbinding all the components. This is not going
>>> to work correctly.
>>>
>>>>>
>>>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}:
>>>>> lock_acquire+0x6c/0x90
>>>>> drm_modeset_acquire_init+0xf4/0x150
>>>>> drmm_mode_config_init+0x220/0x770
>>>>> msm_drm_bind+0x13c/0x654
>>>>> try_to_bring_up_aggregate_device+0x164/0x1d0
>>>>> __component_add+0xa8/0x174
>>>>> component_add+0x18/0x2c
>>>>> dsi_dev_attach+0x24/0x30
>>>>> dsi_host_attach+0x98/0x14c
>>>>> devm_mipi_dsi_attach+0x38/0xb0
>>>>> adv7533_attach_dsi+0x8c/0x110
>>>>> adv7511_probe+0x5a0/0x930
>>>>> i2c_device_probe+0x30c/0x350
>>>>> really_probe.part.0+0x9c/0x2b0
>>>>> __driver_probe_device+0x98/0x144
>>>>> driver_probe_device+0xac/0x14c
>>>>> __device_attach_driver+0xbc/0x124
>>>>> bus_for_each_drv+0x78/0xd0
>>>>> __device_attach+0xa8/0x1c0
>>>>> device_initial_probe+0x18/0x24
>>>>> bus_probe_device+0xa0/0xac
>>>>> deferred_probe_work_func+0x90/0xd0
>>>>> process_one_work+0x28c/0x6b0
>>>>> worker_thread+0x240/0x444
>>>>> kthread+0x110/0x114
>>>>> ret_from_fork+0x10/0x20
>>>>>
>>>>> -> #0 (component_mutex){+.+.}-{3:3}:
>>>>> __lock_acquire+0x1280/0x20ac
>>>>> lock_acquire.part.0+0xe0/0x230
>>>>> lock_acquire+0x6c/0x90
>>>>> __mutex_lock+0x84/0x400
>>>>> mutex_lock_nested+0x3c/0x70
>>>>> component_del+0x34/0x170
>>>>> dsi_dev_detach+0x24/0x30
>>>>> dsi_host_detach+0x20/0x64
>>>>> mipi_dsi_detach+0x2c/0x40
>>>>> adv7533_mode_set+0x64/0x90
>>>>> adv7511_bridge_mode_set+0x210/0x214
>>>>> drm_bridge_chain_mode_set+0x5c/0x84
>>>>> crtc_set_mode+0x18c/0x1dc
>>>>> drm_atomic_helper_commit_modeset_disables+0x40/0x50
>>>>> msm_atomic_commit_tail+0x1d0/0x6e0
>>>>> commit_tail+0xa4/0x180
>>>>> drm_atomic_helper_commit+0x178/0x3b0
>>>>> drm_atomic_commit+0xa4/0xe0
>>>>> drm_client_modeset_commit_atomic+0x228/0x284
>>>>> drm_client_modeset_commit_locked+0x64/0x1d0
>>>>> drm_client_modeset_commit+0x34/0x60
>>>>> drm_fb_helper_lastclose+0x74/0xcc
>>>>> drm_lastclose+0x3c/0x80
>>>>> drm_release+0xfc/0x114
>>>>> __fput+0x70/0x224
>>>>> ____fput+0x14/0x20
>>>>> task_work_run+0x88/0x1a0
>>>>> do_exit+0x350/0xa50
>>>>> do_group_exit+0x38/0xa4
>>>>> __wake_up_parent+0x0/0x34
>>>>> invoke_syscall+0x48/0x114
>>>>> el0_svc_common.constprop.0+0x60/0x11c
>>>>> do_el0_svc+0x30/0xc0
>>>>> el0_svc+0x58/0x100
>>>>> el0t_64_sync_handler+0x1b0/0x1bc
>>>>> el0t_64_sync+0x18c/0x190
>>>>>
>>>>> Due to above reasons, remove the dynamic lane switching
>>>>> code from adv7533 bridge chip and filter out the modes
>>>>> which would need different number of lanes as compared
>>>>> to the initialization time using the mode_valid callback.
>>>>>
>>>>> Suggested-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
>>>>> Signed-off-by: Abhinav Kumar <quic_abhinavk at quicinc.com>
>>>>> ---
>>>>> drivers/gpu/drm/bridge/adv7511/adv7511.h | 3 ++-
>>>>> drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 18 ++++++++++++++----
>>>>> drivers/gpu/drm/bridge/adv7511/adv7533.c | 25 +++++++++++++------------
>>>>> 3 files changed, 29 insertions(+), 17 deletions(-)
>>>>>
>>>>> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h
>>>>> index 9e3bb8a8ee40..0a7cec80b75d 100644
>>>>> --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
>>>>> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
>>>>> @@ -417,7 +417,8 @@ static inline int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511)
>>>>> void adv7533_dsi_power_on(struct adv7511 *adv);
>>>>> void adv7533_dsi_power_off(struct adv7511 *adv);
>>>>> -void adv7533_mode_set(struct adv7511 *adv, const struct drm_display_mode *mode);
>>>>> +enum drm_mode_status adv7533_mode_valid(struct adv7511 *adv,
>>>>> + const struct drm_display_mode *mode);
>>>>> int adv7533_patch_registers(struct adv7511 *adv);
>>>>> int adv7533_patch_cec_registers(struct adv7511 *adv);
>>>>> int adv7533_attach_dsi(struct adv7511 *adv);
>>>>> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
>>>>> index 5bb9300040dd..1115ef9be83c 100644
>>>>> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
>>>>> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
>>>>> @@ -697,7 +697,7 @@ adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
>>>>> }
>>>>> static enum drm_mode_status adv7511_mode_valid(struct adv7511 *adv7511,
>>>>> - struct drm_display_mode *mode)
>>>>> + const struct drm_display_mode *mode)
>>>>> {
>>>>> if (mode->clock > 165000)
>>>>> return MODE_CLOCK_HIGH;
>>>>> @@ -791,9 +791,6 @@ static void adv7511_mode_set(struct adv7511 *adv7511,
>>>>> regmap_update_bits(adv7511->regmap, 0x17,
>>>>> 0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
>>>>> - if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>>>>> - adv7533_mode_set(adv7511, adj_mode);
>>>>> -
>>>>> drm_mode_copy(&adv7511->curr_mode, adj_mode);
>>>>> /*
>>>>> @@ -913,6 +910,18 @@ static void adv7511_bridge_mode_set(struct drm_bridge *bridge,
>>>>> adv7511_mode_set(adv, mode, adj_mode);
>>>>> }
>>>>> +static enum drm_mode_status adv7511_bridge_mode_valid(struct drm_bridge *bridge,
>>>>> + const struct drm_display_info *info,
>>>>> + const struct drm_display_mode *mode)
>>>>> +{
>>>>> + struct adv7511 *adv = bridge_to_adv7511(bridge);
>>>>> +
>>>>> + if (adv->type == ADV7533 || adv->type == ADV7535)
>>>>> + return adv7533_mode_valid(adv, mode);
>>>>> + else
>>>>> + return adv7511_mode_valid(adv, mode);
>>>>> +}
>>>>> +
>>>>> static int adv7511_bridge_attach(struct drm_bridge *bridge,
>>>>> enum drm_bridge_attach_flags flags)
>>>>> {
>>>>> @@ -960,6 +969,7 @@ static const struct drm_bridge_funcs
>>>>> adv7511_bridge_funcs = {
>>>>> .enable = adv7511_bridge_enable,
>>>>> .disable = adv7511_bridge_disable,
>>>>> .mode_set = adv7511_bridge_mode_set,
>>>>> + .mode_valid = adv7511_bridge_mode_valid,
>>>>> .attach = adv7511_bridge_attach,
>>>>> .detect = adv7511_bridge_detect,
>>>>> .get_edid = adv7511_bridge_get_edid,
>>>>> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7533.c b/drivers/gpu/drm/bridge/adv7511/adv7533.c
>>>>> index ef6270806d1d..4a6d45edf431 100644
>>>>> --- a/drivers/gpu/drm/bridge/adv7511/adv7533.c
>>>>> +++ b/drivers/gpu/drm/bridge/adv7511/adv7533.c
>>>>> @@ -100,26 +100,27 @@ void adv7533_dsi_power_off(struct adv7511 *adv)
>>>>> regmap_write(adv->regmap_cec, 0x27, 0x0b);
>>>>> }
>>>>> -void adv7533_mode_set(struct adv7511 *adv, const struct drm_display_mode *mode)
>>>>> +enum drm_mode_status adv7533_mode_valid(struct adv7511 *adv,
>>>>> + const struct drm_display_mode *mode)
>>>>> {
>>>>> + int lanes;
>>>>> struct mipi_dsi_device *dsi = adv->dsi;
>>>>> - int lanes, ret;
>>>>> -
>>>>> - if (adv->num_dsi_lanes != 4)
>>>>> - return;
>>>>> if (mode->clock > 80000)
>>>>> lanes = 4;
>>>>> else
>>>>> lanes = 3;
>>>>> - if (lanes != dsi->lanes) {
>>>>> - mipi_dsi_detach(dsi);
>>>>> - dsi->lanes = lanes;
>>>>> - ret = mipi_dsi_attach(dsi);
>>>>> - if (ret)
>>>>> - dev_err(&dsi->dev, "failed to change host lanes\n");
>>>>> - }
>>>>> + /*
>>>>> + * number of lanes cannot be changed after initialization
>>>>> + * as per section 6.1 of the DSI specification. Hence filter
>>>>> + * out the modes which shall need different number of lanes
>>>>> + * than what was configured in the device tree.
>>>>> + */
>>>>> + if (lanes != dsi->lanes)
>>>>> + return MODE_BAD;
>>>>> +
>>>>> + return MODE_OK;
>>>>> }
>>>>> int adv7533_patch_registers(struct adv7511 *adv)
>
More information about the Freedreno
mailing list