[Freedreno] [PATCH v2 10/12] arm64: dts: qcom: sm6115: Add i2c/spi nodes
Konrad Dybcio
konrad.dybcio at linaro.org
Fri Dec 2 10:51:24 UTC 2022
On 30.11.2022 21:09, Adam Skladowski wrote:
> Add I2C/SPI nodes for SM6115.
>
> Signed-off-by: Adam Skladowski <a39.skl at gmail.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm6115.dtsi | 290 +++++++++++++++++++++++++++
> 1 file changed, 290 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> index b30a5485671d..e676b9d117e3 100644
> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> @@ -6,6 +6,7 @@
> #include <dt-bindings/clock/qcom,gcc-sm6115.h>
> #include <dt-bindings/clock/qcom,sm6115-dispcc.h>
> #include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/dma/qcom-gpi.h>
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/power/qcom-rpmpd.h>
> @@ -365,6 +366,90 @@ tlmm: pinctrl at 500000 {
> interrupt-controller;
> #interrupt-cells = <2>;
>
> + qup_i2c0_default: qup-i2c0-default-state {
> + pins = "gpio0", "gpio1";
> + function = "qup0";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c1_default: qup-i2c1-default-state {
> + pins = "gpio4", "gpio5";
> + function = "qup1";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c2_default: qup-i2c2-default-state {
> + pins = "gpio6", "gpio7";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c3_default: qup-i2c3-default-state {
> + pins = "gpio8", "gpio9";
> + function = "qup3";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c4_default: qup-i2c4-default-state {
> + pins = "gpio12", "gpio13";
> + function = "qup4";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c5_default: qup-i2c5-default-state {
> + pins = "gpio14", "gpio15";
> + function = "qup5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi0_default: qup-spi0-default-state {
> + pins = "gpio0", "gpio1","gpio2", "gpio3";
> + function = "qup0";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi1_default: qup-spi1-default-state {
> + pins = "gpio4", "gpio5", "gpio69", "gpio70";
> + function = "qup1";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi2_default: qup-spi2-default-state {
> + pins = "gpio6", "gpio7", "gpio71", "gpio80";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi3_default: qup-spi3-default-state {
> + pins = "gpio8", "gpio9", "gpio10", "gpio11";
> + function = "qup3";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi4_default: qup-spi4-default-state {
> + pins = "gpio12", "gpio13", "gpio96", "gpio97";
> + function = "qup4";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi5_default: qup-spi5-default-state {
> + pins = "gpio14", "gpio15", "gpio16", "gpio17";
> + function = "qup5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> sdc1_state_on: sdc1-on-state {
> clk-pins {
> pins = "sdc1_clk";
> @@ -701,6 +786,211 @@ gpi_dma0: dma-controller at 4a00000 {
> status = "disabled";
> };
>
> + qupv3_id_0: geniqup at 4ac0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0x04ac0000 0x2000>;
> + clock-names = "m-ahb", "s-ahb";
> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + iommus = <&apps_smmu 0xe3 0x0>;
> + ranges;
> + status = "disabled";
> +
> + i2c0: i2c at 4a80000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x04a80000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c0_default>;
> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 0 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi0: spi at 4a80000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x04a80000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi0_default>;
> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 0 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c at 4a84000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x04a84000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c1_default>;
> + interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 1 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi1: spi at 4a84000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x04a84000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi1_default>;
> + interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 1 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 4a88000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x04a88000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c2_default>;
> + interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 2 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi2: spi at 4a88000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x04a88000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi2_default>;
> + interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 2 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c at 4a8c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x04a8c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c3_default>;
> + interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 3 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi3: spi at 4a8c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x04a8c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi3_default>;
> + interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 3 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c at 4a90000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x04a90000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c4_default>;
> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 4 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi4: spi at 4a90000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x04a90000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi4_default>;
> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 4 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c5: i2c at 4a94000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x04a94000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c5_default>;
> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 5 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi5: spi at 4a94000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x04a94000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi5_default>;
> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 5 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> usb_1: usb at 4ef8800 {
> compatible = "qcom,sm6115-dwc3", "qcom,dwc3";
> reg = <0x04ef8800 0x400>;
More information about the Freedreno
mailing list