[Freedreno] [RFC PATCH 3/6] drm/msm/dpu1: Wire up DSC mask for active CTL configuration

[Dmitry Baryshkov]

On 14/12/2022 21:30, Marijn Suijten wrote:
> On 2022-12-14 20:43:29, Dmitry Baryshkov wrote:
>> On 14/12/2022 01:22, Marijn Suijten wrote:
>>> Active CTLs have to configure what DSC block(s) have to be enabled, and
>>> what DSC block(s) have to be flushed; this value was initialized to zero
>>> resulting in the necessary register writes to never happen (or would
>>> write zero otherwise).  This seems to have gotten lost in the DSC v4->v5
>>> series while refactoring how the combination with merge_3d was handled.
>>>
>>> Fixes: 58dca9810749 ("drm/msm/disp/dpu1: Add support for DSC in encoder")
>>> Signed-off-by: Marijn Suijten <marijn.suijten at somainline.org>
>>> ---
>>>    drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 1 +
>>>    drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 1 +
>>>    drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c  | 2 ++
>>>    3 files changed, 4 insertions(+)
>>>
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> index ae28b2b93e69..35791f93c33d 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> @@ -61,6 +61,7 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
>>>    	intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_CMD;
>>>    	intf_cfg.stream_sel = cmd_enc->stream_sel;
>>>    	intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc);
>>> +	intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
>>>    	ctl->ops.setup_intf_cfg(ctl, &intf_cfg);
>>>    
>>>    	/* setup which pp blk will connect to this intf */
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> index 0f71e8fe7be7..9ee3a7306a5f 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> @@ -274,6 +274,7 @@ static void dpu_encoder_phys_vid_setup_timing_engine(
>>>    	intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_VID;
>>>    	intf_cfg.stream_sel = 0; /* Don't care value for video mode */
>>>    	intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc);
>>> +	intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
>>>    	if (phys_enc->hw_pp->merge_3d)
>>>    		intf_cfg.merge_3d = phys_enc->hw_pp->merge_3d->idx;
>>>    
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c
>>> index 7cbcef6efe17..92ddf9995b37 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c
>>> @@ -209,6 +209,7 @@ static void dpu_encoder_phys_wb_setup_cdp(struct dpu_encoder_phys *phys_enc)
>>>    
>>>    		intf_cfg.intf = DPU_NONE;
>>>    		intf_cfg.wb = hw_wb->idx;
>>> +		intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
>>
>> We usually don't have DSC with the writeback, don't we?
> 
> I am unsure so ended up adding them in writeback regardless.  Downstream
> uses a separate callback to process intf_cfg.dsc instead of going
> through setup_intf_cfg().
> 
> To prevent these from being missed again (in the case of copy&paste),
> how about instead having some function that sets up intf_cfg with these
> default values from a phys_enc?  That way most of this remains oblivious
> to the caller.

I'm not sure this is possible. E.g. intf_cfg.dsc should not be set for 
the WB.

> 
> On the same note, that callback on non-DPU_CTL_ACTIVE_CFG hardware
> doesn't use the intf_cfg.dsc member anyway, but it was again added to
> keep the blocks somewhat consistent (in case it ever becomes used?).
> 
>>>    		if (mode_3d && hw_pp && hw_pp->merge_3d)
>>>    			intf_cfg.merge_3d = hw_pp->merge_3d->idx;
>>> @@ -230,6 +231,7 @@ static void dpu_encoder_phys_wb_setup_cdp(struct dpu_encoder_phys *phys_enc)
>>>    		intf_cfg.wb = hw_wb->idx;
>>>    		intf_cfg.mode_3d =
>>>    			dpu_encoder_helper_get_3d_blend_mode(phys_enc);
>>> +		intf_cfg.dsc = dpu_encoder_helper_get_dsc(phys_enc);
>>>    		phys_enc->hw_ctl->ops.setup_intf_cfg(phys_enc->hw_ctl, &intf_cfg);
>>>    	}
>>>    }
> 
> - Marijn

-- 
With best wishes
Dmitry