[Freedreno] [PATCH v2 2/4] arm64: dts: qcom: sc7280: Add support for eDP panel on CRD

[Bjorn Andersson]

On Tue 08 Feb 07:18 PST 2022, Sankeerth Billakanti wrote:

> Enable the eDP display panel support without HPD on sc7280 platform.
> 
> Signed-off-by: Sankeerth Billakanti <quic_sbillaka at quicinc.com>
> ---
> 
> Changes in v2:
>   - sort node references alphabetically
>   - improve readability
>   - move the pwm pinctrl to pwm node
>   - move the regulators to root
>   - define backlight power
>   - remove dummy regulator node
>   - cleanup pinctrl definitions
> 
>  arch/arm64/boot/dts/qcom/sc7280-crd.dts | 122 ++++++++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280.dtsi    |   2 -
>  2 files changed, 122 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> index e2efbdd..bff2707 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> @@ -21,6 +21,34 @@
>  	chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
> +
> +	backlight_power: backlight-power {
> +		compatible = "regulator-fixed";
> +		regulator-name = "backlight_power";
> +
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +
> +		gpio = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&edp_bl_power>;
> +	};
> +
> +	edp_power: edp-power {
> +		compatible = "regulator-fixed";
> +		regulator-name = "edp_power";
> +
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&edp_panel_power>;
> +	};
>  };
>  
>  &apps_rsc {
> @@ -76,6 +104,42 @@ ap_ts_pen_1v8: &i2c13 {
>  	};
>  };
>  
> +&edp_out {

Sorry for missing this while merging changes in sc7280.dtsi. But it
would be really nice if this was labeled mdss_edp_out instead (or
possibly defined within the &mdss_edp node).

Now you will have &edp_out and &dp_out floating around away from the edp
and dp nodes...

> +	remote-endpoint = <&edp_panel_in>;
> +};
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_edp {
> +	status = "okay";
> +
> +	vdda-1p2-supply = <&vreg_l6b_1p2>;
> +	vdda-0p9-supply = <&vreg_l10c_0p8>;
> +};
> +
> +&mdss_edp_phy {
> +	status = "okay";
> +
> +	vdda-1p2-supply = <&vreg_l6b_1p2>;
> +	vdda-0p9-supply = <&vreg_l10c_0p8>;
> +};
> +
> +&mdss_dp {
> +	status = "okay";
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&dp_hot_plug_det>;
> +	data-lanes = <0 1>;
> +	vdda-1p2-supply = <&vreg_l6b_1p2>;
> +	vdda-0p9-supply = <&vreg_l1b_0p8>;
> +};
> +
> +&mdss_mdp {
> +	status = "okay";
> +};
> +
>  &nvme_3v3_regulator {
>  	gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
>  };
> @@ -84,7 +148,65 @@ ap_ts_pen_1v8: &i2c13 {
>  	pins = "gpio51";
>  };
>  
> +&pm8350c_pwm {

This label doesn't exist, so I won't be able to merge this patch.

> +	status = "okay";
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&edp_bl_pwm>;
> +};
> +
> +&pm8350c_gpios {
> +	edp_bl_power: edp-bl-power {
> +		pins = "gpio7";
> +		function = "normal";
> +		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
> +		bias-disable;
> +		output-low;
> +	};
> +
> +	edp_bl_pwm: edp-bl-pwm {
> +		pins = "gpio8";
> +		function = "func1";
> +		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
> +		bias-disable;
> +		output-low;
> +	};
> +};
> +
> +&soc {
> +	edp_backlight: edp-backlight {
> +		compatible = "pwm-backlight";

This is not a device on the mmio bus, so it should not love within the
&soc.

> +
> +		power-supply = <&backlight_power>;
> +		pwms = <&pm8350c_pwm 3 65535>;
> +	};
> +
> +	edp_panel: edp_panel {

Ditto.

Regards,
Bjorn

> +		compatible = "sharp,lq140m1jw46";
> +
> +		power-supply = <&edp_power>;
> +		backlight = <&edp_backlight>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			port at 0 {
> +				reg = <0>;
> +				edp_panel_in: endpoint {
> +					remote-endpoint = <&edp_out>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
>  &tlmm {
> +	edp_panel_power: edp-panel-power {
> +		pins = "gpio80";
> +		function = "gpio";
> +		bias-pull-down;
> +	};
> +
>  	tp_int_odl: tp-int-odl {
>  		pins = "gpio7";
>  		function = "gpio";
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 3572399..f8fa716 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -3012,8 +3012,6 @@
>  
>  			mdss_edp: edp at aea0000 {
>  				compatible = "qcom,sc7280-edp";
> -				pinctrl-names = "default";
> -				pinctrl-0 = <&edp_hot_plug_det>;
>  
>  				reg = <0 0xaea0000 0 0x200>,
>  				      <0 0xaea0200 0 0x200>,
> -- 
> 2.7.4
>