[Freedreno] [PATCH v3 2/4] arm64: dts: qcom: sc7280: Add support for eDP panel on CRD

[Stephen Boyd]

Quoting Sankeerth Billakanti (2022-02-09 00:55:30)
> Enable the eDP display panel support without HPD on sc7280 platform.
>
> Signed-off-by: Sankeerth Billakanti <quic_sbillaka at quicinc.com>
> ---
>
> Changes in v3:
>   - Sort the nodes alphabetically
>   - Use - instead of _ as node names
>   - Place the backlight and panel nodes under root
>   - Change the name of edp_out to mdss_edp_out
>   - Change the names of regulator nodes
>   - Delete unused properties in the board file
>
>
> Changes in v2:
>   - Sort node references alphabetically
>   - Improve readability
>   - Move the pwm pinctrl to pwm node
>   - Move the regulators to root
>   - Define backlight power
>   - Remove dummy regulator node
>   - Cleanup pinctrl definitions
>
>  arch/arm64/boot/dts/qcom/sc7280-crd.dts | 122 ++++++++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280.dtsi    |   2 +-
>  2 files changed, 123 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> index e2efbdd..2a490a0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> @@ -21,6 +21,59 @@
>         chosen {
>                 stdout-path = "serial0:115200n8";
>         };
> +
> +       backlight_3v3_regulator: backlight-3v3-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "backlight_3v3_regulator";
> +
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +
> +               gpio = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
> +               enable-active-high;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&edp_bl_power>;
> +       };
> +
> +       edp_3v3_regulator: edp-3v3-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "edp_3v3_regulator";
> +
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +
> +               gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
> +               enable-active-high;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&edp_panel_power>;
> +       };
> +
> +       edp_backlight: edp-backlight {
> +               compatible = "pwm-backlight";
> +
> +               power-supply = <&backlight_3v3_regulator>;
> +               pwms = <&pm8350c_pwm 3 65535>;
> +       };
> +
> +       edp_panel: edp-panel {
> +               compatible = "sharp,lq140m1jw46";
> +
> +               power-supply = <&edp_3v3_regulator>;
> +               backlight = <&edp_backlight>;
> +
> +               ports {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       port at 0 {
> +                               reg = <0>;
> +                               edp_panel_in: endpoint {
> +                                       remote-endpoint = <&edp_out>;

Where is edp_out now?

> +                               };
> +                       };
> +               };
> +       };
>  };
>
>  &apps_rsc {
> @@ -76,6 +129,44 @@ ap_ts_pen_1v8: &i2c13 {
>         };
>  };
>
> +&mdss {
> +       status = "okay";
> +};
> +
> +&mdss_dp {
> +       status = "okay";
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&dp_hot_plug_det>;
> +       data-lanes = <0 1>;
> +       vdda-1p2-supply = <&vreg_l6b_1p2>;
> +       vdda-0p9-supply = <&vreg_l1b_0p8>;
> +};
> +
> +&mdss_edp {
> +       status = "okay";
> +
> +       vdda-1p2-supply = <&vreg_l6b_1p2>;
> +       vdda-0p9-supply = <&vreg_l10c_0p8>;
> +       /delete-property/ pinctrl-names;
> +       /delete-property/ pinctrl-0;
> +};
> +
> +&mdss_edp_out {
> +       remote-endpoint = <&edp_panel_in>;
> +};
> +
> +&mdss_edp_phy {
> +       status = "okay";
> +
> +       vdda-1p2-supply = <&vreg_l6b_1p2>;
> +       vdda-0p9-supply = <&vreg_l10c_0p8>;
> +};
> +
> +&mdss_mdp {
> +       status = "okay";
> +};
> +
>  &nvme_3v3_regulator {
>         gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
>  };
> @@ -84,7 +175,38 @@ ap_ts_pen_1v8: &i2c13 {
>         pins = "gpio51";
>  };
>
> +&pm8350c_gpios {
> +       edp_bl_power: edp-bl-power {
> +               pins = "gpio7";
> +               function = "normal";
> +               qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
> +               bias-disable;
> +               output-low;

Is the 'output-low' necessary?

> +       };
> +
> +       edp_bl_pwm: edp-bl-pwm {
> +               pins = "gpio8";
> +               function = "func1";
> +               qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
> +               bias-disable;
> +               output-low;

Same question.

> +       };
> +};
> +
> +&pm8350c_pwm {
> +       status = "okay";
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&edp_bl_pwm>;
> +};
> +
>  &tlmm {
> +       edp_panel_power: edp-panel-power {
> +               pins = "gpio80";
> +               function = "gpio";
> +               bias-pull-down;
> +       };
> +
>         tp_int_odl: tp-int-odl {
>                 pins = "gpio7";
>                 function = "gpio";
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 3572399..eca403a 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -3066,7 +3066,7 @@
>
>                                         port at 1 {
>                                                 reg = <1>;
> -                                               edp_out: endpoint { };
> +                                               mdss_edp_out: endpoint { };
>                                         };

It feels like this should be a different patch for this phandle rename.