[Freedreno] [PATCH] drm/msm/dp: add wide bus support
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Mon Jan 31 20:57:44 UTC 2022
On 31/01/2022 23:50, Kuogee Hsieh wrote:
>
> On 1/28/2022 8:59 PM, Dmitry Baryshkov wrote:
>> Hi,
>>
>> Thank you for your patch.
>>
>> On Fri, 28 Jan 2022 at 20:29, Kuogee Hsieh <quic_khsieh at quicinc.com>
>> wrote:
>>> Normally, mdp will push one pixel of data per pixel clock to
>>> interface to display. Wide bus feature will increase bus
>>> width from 32 bits to 64 bits so that it can push two
>>> pixel of data per pixel clock to interface to display.
>>> This feature is pre requirement to support 4k resolution.
>>>
>>> Signed-off-by: Kuogee Hsieh <quic_khsieh at quicinc.com>
>>> ---
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 16 ++-
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h | 2 +
>>> .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 14 +++
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 108
>>> +++++++++++++++------
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h | 5 +
>>> drivers/gpu/drm/msm/dp/dp_catalog.c | 11 ++-
>>> drivers/gpu/drm/msm/dp/dp_catalog.h | 1 +
>>> drivers/gpu/drm/msm/dp/dp_ctrl.c | 9 +-
>>> drivers/gpu/drm/msm/dp/dp_ctrl.h | 1 +
>>> drivers/gpu/drm/msm/dp/dp_display.c | 17 ++++
>>> drivers/gpu/drm/msm/dp/dp_display.h | 3 +
>>> drivers/gpu/drm/msm/dp/dp_parser.c | 26 +++++
>>> drivers/gpu/drm/msm/dp/dp_parser.h | 2 +
>>> drivers/gpu/drm/msm/msm_drv.h | 9 ++
>> Can we get this split into logical chunks please?
>>
>>> 14 files changed, 190 insertions(+), 34 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> index 1e648db..e2fb5bc 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> @@ -199,6 +199,8 @@ struct dpu_encoder_virt {
>>>
>>> struct msm_display_info disp_info;
>>>
>>> + struct msm_op_info op_info;
>>> +
>>> bool idle_pc_supported;
>>> struct mutex rc_lock;
>>> enum dpu_enc_rc_states rc_state;
>>> @@ -217,6 +219,13 @@ static u32 dither_matrix[DITHER_MATRIX_SZ] = {
>>> 15, 7, 13, 5, 3, 11, 1, 9, 12, 4, 14, 6, 0, 8, 2, 10
>>> };
>>>
>>> +bool dpu_encoder_is_widebus_enabled(struct drm_encoder *drm_enc)
>>> +{
>>> + struct dpu_encoder_virt *dpu_enc = to_dpu_encoder_virt(drm_enc);
>>> +
>>> + return dpu_enc->op_info.wide_bus_en;
>>> +}
>>> +
>>> static void _dpu_encoder_setup_dither(struct dpu_hw_pingpong
>>> *hw_pp, unsigned bpc)
>>> {
>>> struct dpu_hw_dither_cfg dither_cfg = { 0 };
>>> @@ -2112,6 +2121,7 @@ int dpu_encoder_setup(struct drm_device *dev,
>>> struct drm_encoder *enc,
>>> struct dpu_kms *dpu_kms = to_dpu_kms(priv->kms);
>>> struct drm_encoder *drm_enc = NULL;
>>> struct dpu_encoder_virt *dpu_enc = NULL;
>>> + struct msm_op_info *op_info;
>>> int ret = 0;
>>>
>>> dpu_enc = to_dpu_encoder_virt(enc);
>>> @@ -2128,8 +2138,12 @@ int dpu_encoder_setup(struct drm_device *dev,
>>> struct drm_encoder *enc,
>>> timer_setup(&dpu_enc->vsync_event_timer,
>>> dpu_encoder_vsync_event_handler,
>>> 0);
>>> - else if (disp_info->intf_type == DRM_MODE_ENCODER_TMDS)
>>> + else if (disp_info->intf_type == DRM_MODE_ENCODER_TMDS) {
>>> dpu_enc->dp = priv->dp[disp_info->h_tile_instance[0]];
>>> + op_info = &priv->op_info[disp_info->h_tile_instance[0]];
>> op_info should be defined per INTF rather than per h_tile. This way
>> you won't have to check for intf_type here.
>>
>>> + dpu_enc->op_info = *op_info;
>> So... we set this data in msm_drm_private only to copy it to
>> dpu_encoder_virt? Please don't do this.
>> Allow one to query the data from the DP rather than blindly copying it
>> over and over again.
>>
>>> +
>>> + }
>>>
>>> INIT_DELAYED_WORK(&dpu_enc->delayed_off_work,
>>> dpu_encoder_off_work);
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
>>> index e241914..0d73550 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
>>> @@ -168,4 +168,6 @@ int dpu_encoder_get_linecount(struct drm_encoder
>>> *drm_enc);
>>> */
>>> int dpu_encoder_get_vsync_count(struct drm_encoder *drm_enc);
>>>
>>> +bool dpu_encoder_is_widebus_enabled(struct drm_encoder *drm_enc);
>>> +
>>> #endif /* __DPU_ENCODER_H__ */
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> index ddd9d89..04ac2dc 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> @@ -110,6 +110,20 @@ static void drm_mode_to_intf_timing_params(
>>> timing->v_back_porch += timing->v_front_porch;
>>> timing->v_front_porch = 0;
>>> }
>>> +
>>> + timing->wide_bus_en =
>>> dpu_encoder_is_widebus_enabled(phys_enc->parent);
>>> +
>>> + /*
>>> + * for DP, divide the horizonal parameters by 2 when
>>> + * widebus is enabled
>>> + */
>>> + if (phys_enc->hw_intf->cap->type == INTF_DP &&
>>> timing->wide_bus_en) {
>> What about INTF_eDP?
>> I suspect that intf type check is unnecessary here.
>>
>>> + timing->width = timing->width >> 1;
>>> + timing->xres = timing->xres >> 1;
>>> + timing->h_back_porch = timing->h_back_porch >> 1;
>>> + timing->h_front_porch = timing->h_front_porch >> 1;
>>> + timing->hsync_pulse_width = timing->hsync_pulse_width
>>> >> 1;
>>> + }
>>> }
>>>
>>> static u32 get_horizontal_total(const struct intf_timing_params
>>> *timing)
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> index 116e2b5..f072bd5 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> @@ -33,6 +33,7 @@
>>> #define INTF_TP_COLOR1 0x05C
>>> #define INTF_CONFIG2 0x060
>>> #define INTF_DISPLAY_DATA_HCTL 0x064
>>> +#define INTF_ACTIVE_DATA_HCTL 0x068
>>> #define INTF_FRAME_LINE_COUNT_EN 0x0A8
>>> #define INTF_FRAME_COUNT 0x0AC
>>> #define INTF_LINE_COUNT 0x0B0
>>> @@ -90,67 +91,109 @@ static void
>>> dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
>>> u32 hsync_period, vsync_period;
>>> u32 display_v_start, display_v_end;
>>> u32 hsync_start_x, hsync_end_x;
>>> + u32 hsync_data_start_x, hsync_data_end_x;
>>> u32 active_h_start, active_h_end;
>>> u32 active_v_start, active_v_end;
>>> u32 active_hctl, display_hctl, hsync_ctl;
>>> u32 polarity_ctl, den_polarity, hsync_polarity, vsync_polarity;
>>> u32 panel_format;
>>> - u32 intf_cfg, intf_cfg2 = 0, display_data_hctl = 0;
>>> + u32 intf_cfg, intf_cfg2 = 0;
>>> + u32 display_data_hctl = 0, active_data_hctl = 0;
>>> + u32 data_width;
>>> + bool dp_intf = false;
>>>
>>> /* read interface_cfg */
>>> intf_cfg = DPU_REG_READ(c, INTF_CONFIG);
>>> +
>>> + if (ctx->cap->type == INTF_EDP || ctx->cap->type == INTF_DP)
>>> + dp_intf = true;
>>> +
>>> hsync_period = p->hsync_pulse_width + p->h_back_porch +
>>> p->width +
>>> p->h_front_porch;
>>> vsync_period = p->vsync_pulse_width + p->v_back_porch +
>>> p->height +
>>> p->v_front_porch;
>>>
>>> display_v_start = ((p->vsync_pulse_width + p->v_back_porch) *
>>> - hsync_period) + p->hsync_skew;
>>> + hsync_period) + p->hsync_skew;
>> Unnecessary whitespace changes complicate reviewing. I'll try groking
>> this piece of code later.
>>
>>> display_v_end = ((vsync_period - p->v_front_porch) *
>>> hsync_period) +
>>> - p->hsync_skew - 1;
>>> + p->hsync_skew - 1;
>>> +
>>> + hsync_ctl = (hsync_period << 16) | p->hsync_pulse_width;
>>>
>>> hsync_start_x = p->h_back_porch + p->hsync_pulse_width;
>>> hsync_end_x = hsync_period - p->h_front_porch - 1;
>>>
>>> - if (p->width != p->xres) {
>>> - active_h_start = hsync_start_x;
>>> - active_h_end = active_h_start + p->xres - 1;
>>> - } else {
>>> - active_h_start = 0;
>>> - active_h_end = 0;
>>> - }
>>> + /*
>>> + * DATA_HCTL_EN controls data timing which can be different from
>>> + * video timing. It is recommended to enable it for all
>>> cases, except
>>> + * if compression is enabled in 1 pixel per clock mode
>>> + */
>>> + if (!p->compression_en || p->wide_bus_en)
>>> + intf_cfg2 |= BIT(4);
>>>
>>> - if (p->height != p->yres) {
>>> - active_v_start = display_v_start;
>>> - active_v_end = active_v_start + (p->yres *
>>> hsync_period) - 1;
>>> - } else {
>>> - active_v_start = 0;
>>> - active_v_end = 0;
>>> - }
>>> + if (p->wide_bus_en)
>>> + intf_cfg2 |= BIT(0);
>>> +
>>> + /*
>>> + * If widebus is disabled:
>>> + * For uncompressed stream, the data is valid for the entire
>>> active
>>> + * window period.
>>> + * For compressed stream, data is valid for a shorter time
>>> period
>>> + * inside the active window depending on the compression ratio.
>>> + *
>>> + * If widebus is enabled:
>>> + * For uncompressed stream, data is valid for only half the
>>> active
>>> + * window, since the data rate is doubled in this mode.
>>> + * p->width holds the adjusted width for DP but unadjusted
>>> width for DSI
>>> + * For compressed stream, data validity window needs to be
>>> adjusted for
>>> + * compression ratio and then further halved.
>>> + */
>>> + data_width = p->width;
>>> +
>>> + if (p->compression_en) {
>>> + data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 3);
>>>
>>> - if (active_h_end) {
>>> - active_hctl = (active_h_end << 16) | active_h_start;
>>> - intf_cfg |= BIT(29); /* ACTIVE_H_ENABLE */
>>> + if (p->wide_bus_en)
>>> + data_width >>= 1;
>>> + } else if (!dp_intf && p->wide_bus_en) {
>>> + data_width = p->width >> 1;
>>> } else {
>>> - active_hctl = 0;
>>> + data_width = p->width;
>>> }
>>>
>>> - if (active_v_end)
>>> - intf_cfg |= BIT(30); /* ACTIVE_V_ENABLE */
>>> + hsync_data_start_x = hsync_start_x;
>>> + hsync_data_end_x = hsync_start_x + data_width - 1;
>>>
>>> - hsync_ctl = (hsync_period << 16) | p->hsync_pulse_width;
>>> display_hctl = (hsync_end_x << 16) | hsync_start_x;
>>> + display_data_hctl = (hsync_data_end_x << 16) |
>>> hsync_data_start_x;
>>>
>>> - if (ctx->cap->type == INTF_EDP || ctx->cap->type == INTF_DP) {
>>> - active_h_start = hsync_start_x;
>>> - active_h_end = active_h_start + p->xres - 1;
>>> - active_v_start = display_v_start;
>>> - active_v_end = active_v_start + (p->yres *
>>> hsync_period) - 1;
>>> -
>>> + if (dp_intf) {
>>> + // DP timing adjustment
>>> display_v_start += p->hsync_pulse_width +
>>> p->h_back_porch;
>>> + display_v_end -= p->h_front_porch;
>>> + }
>>>
>>> - active_hctl = (active_h_end << 16) | active_h_start;
>>> +
>>> + active_h_start = hsync_start_x;
>>> + active_h_end = active_h_start + p->xres - 1;
>>> +
>>> + active_v_start = display_v_start;
>>> + active_v_end = active_v_start + (p->yres * hsync_period) - 1;
>>> +
>>> + intf_cfg |= BIT(29); /* ACTIVE_H_ENABLE */
>>> + intf_cfg |= BIT(30); /* ACTIVE_V_ENABLE */
>>> +
>>> + active_hctl = (active_h_end << 16) | active_h_start;
>>> +
>>> + if (dp_intf) {
>>> display_hctl = active_hctl;
>>> + if (p->compression_en) {
>> I assume that compression_en is a part of DSC support for the DP,
>> isn't it?
>> If so, it should definitely come as a separate patch.
>>
>>> + active_data_hctl = (hsync_start_x +
>>> + p->extra_dto_cycles) << 16;
>>> + active_data_hctl += hsync_start_x;
>>> +
>>> + display_data_hctl = active_data_hctl;
>>> + }
>>> }
>>>
>>> den_polarity = 0;
>>> @@ -204,6 +247,9 @@ static void
>>> dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
>>> DPU_REG_WRITE(c, INTF_FRAME_LINE_COUNT_EN, 0x3);
>>> DPU_REG_WRITE(c, INTF_CONFIG, intf_cfg);
>>> DPU_REG_WRITE(c, INTF_PANEL_FORMAT, panel_format);
>>> + DPU_REG_WRITE(c, INTF_CONFIG2, intf_cfg2);
>>> + DPU_REG_WRITE(c, INTF_DISPLAY_DATA_HCTL, display_data_hctl);
>>> + DPU_REG_WRITE(c, INTF_ACTIVE_DATA_HCTL, active_data_hctl);
>> Are these registers present on all supported hardware (like sdm845)?
>> Does msm8998 support them? msm8996?
>
> no, i think they are start from sm8250 (Kona).
>
> But they should be no effects after write.
ok. Let's see how would this code fragment evolve if you remove dp_intf
and compression_en.
>
>>> }
>>>
>>> static void dpu_hw_intf_enable_timing_engine(
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> index 3568be8..8fc71ce 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> @@ -30,6 +30,11 @@ struct intf_timing_params {
>>> u32 border_clr;
>>> u32 underflow_clr;
>>> u32 hsync_skew;
>>> +
>>> + bool wide_bus_en;
>>> + bool compression_en;
>>> + u32 extra_dto_cycles; /* for DP only */
>>> + u32 dce_bytes_per_line;
>> All compression-related items should come in a separate patch.
>>
>>> };
>>>
>>> struct intf_prog_fetch {
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_catalog.c
>>> b/drivers/gpu/drm/msm/dp/dp_catalog.c
>>> index 6d6850e..d738e2e 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_catalog.c
>>> +++ b/drivers/gpu/drm/msm/dp/dp_catalog.c
>>> @@ -745,6 +745,7 @@ int dp_catalog_panel_timing_cfg(struct dp_catalog
>>> *dp_catalog)
>>> {
>>> struct dp_catalog_private *catalog = container_of(dp_catalog,
>>> struct dp_catalog_private, dp_catalog);
>>> + u32 reg;
>>>
>>> dp_write_link(catalog, REG_DP_TOTAL_HOR_VER,
>>> dp_catalog->total);
>>> @@ -753,7 +754,15 @@ int dp_catalog_panel_timing_cfg(struct
>>> dp_catalog *dp_catalog)
>>> dp_write_link(catalog, REG_DP_HSYNC_VSYNC_WIDTH_POLARITY,
>>> dp_catalog->width_blanking);
>>> dp_write_link(catalog, REG_DP_ACTIVE_HOR_VER,
>>> dp_catalog->dp_active);
>>> - dp_write_p0(catalog, MMSS_DP_INTF_CONFIG, 0);
>>> +
>>> + reg = dp_read_p0(catalog, MMSS_DP_INTF_CONFIG);
>>> +
>>> + if (dp_catalog->wide_bus_en)
>>> + reg |= BIT(4);
>>> + else
>>> + reg &= ~BIT(4);
>>> +
>>> + dp_write_p0(catalog, MMSS_DP_INTF_CONFIG, reg);
>>> return 0;
>>> }
>>>
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_catalog.h
>>> b/drivers/gpu/drm/msm/dp/dp_catalog.h
>>> index 7dea101..6ca563f 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_catalog.h
>>> +++ b/drivers/gpu/drm/msm/dp/dp_catalog.h
>>> @@ -70,6 +70,7 @@ struct dp_catalog {
>>> enum dp_catalog_audio_sdp_type sdp_type;
>>> enum dp_catalog_audio_header_type sdp_header;
>>> u32 audio_data;
>>> + bool wide_bus_en;
>>> };
>>>
>>> /* Debug module */
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c
>>> b/drivers/gpu/drm/msm/dp/dp_ctrl.c
>>> index 53ad3af..401ae57 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
>>> +++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
>>> @@ -1812,6 +1812,7 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
>>> int ret = 0;
>>> bool mainlink_ready = false;
>>> struct dp_ctrl_private *ctrl;
>>> + u32 pixel_rate_orig;
>>>
>>> if (!dp_ctrl)
>>> return -EINVAL;
>>> @@ -1820,6 +1821,10 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
>>>
>>> ctrl->dp_ctrl.pixel_rate = ctrl->panel->dp_mode.drm_mode.clock;
>>>
>>> + pixel_rate_orig = ctrl->dp_ctrl.pixel_rate;
>>> + if (dp_ctrl->wide_bus_en)
>>> + ctrl->dp_ctrl.pixel_rate >>= 1;
>>> +
>>> drm_dbg_dp((struct drm_device *)NULL, "rate=%d,
>>> num_lanes=%d, pixel_rate=%d\n",
>>> ctrl->link->link_params.rate,
>>> ctrl->link->link_params.num_lanes,
>>> ctrl->dp_ctrl.pixel_rate);
>>> @@ -1855,11 +1860,13 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
>>> */
>>> reinit_completion(&ctrl->video_comp);
>>>
>>> + ctrl->catalog->wide_bus_en = dp_ctrl->wide_bus_en;
>> Can you limit the DP's knowledge of wide_bus_en to a single place
>> (e.g. only in dp_catalog or in dp_ctrl)? Just copying the data bit
>> means that we have two places which must be kept in sync.
>>
>>> +
>>> dp_ctrl_configure_source_params(ctrl);
>>>
>>> dp_catalog_ctrl_config_msa(ctrl->catalog,
>>> ctrl->link->link_params.rate,
>>> - ctrl->dp_ctrl.pixel_rate, dp_ctrl_use_fixed_nvid(ctrl));
>>> + pixel_rate_orig, dp_ctrl_use_fixed_nvid(ctrl));
>>>
>>> dp_ctrl_setup_tr_unit(ctrl);
>>>
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.h
>>> b/drivers/gpu/drm/msm/dp/dp_ctrl.h
>>> index 2433edb..4dff44d 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_ctrl.h
>>> +++ b/drivers/gpu/drm/msm/dp/dp_ctrl.h
>>> @@ -17,6 +17,7 @@ struct dp_ctrl {
>>> bool orientation;
>>> atomic_t aborted;
>>> u32 pixel_rate;
>>> + bool wide_bus_en;
>>> };
>>>
>>> int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl);
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c
>>> b/drivers/gpu/drm/msm/dp/dp_display.c
>>> index f89f3ed..924c9e2 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c
>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c
>>> @@ -873,6 +873,8 @@ static int dp_display_enable(struct
>>> dp_display_private *dp, u32 data)
>>> return 0;
>>> }
>>>
>>> + dp->ctrl->wide_bus_en = dp_display->wide_bus_en;
>> Ugh. This adds a third place. dp_display, dp_ctrl and dp_catalog. Too
>> much for a single bit.
>>
>>> +
>>> rc = dp_ctrl_on_stream(dp->ctrl);
>>> if (!rc)
>>> dp_display->power_on = true;
>>> @@ -1004,6 +1006,8 @@ int dp_display_get_modes(struct msm_dp *dp,
>>> dp->connector, dp_mode);
>>> if (dp_mode->drm_mode.clock)
>>> dp->max_pclk_khz = dp_mode->drm_mode.clock;
>>> +
>>> + DRM_DEBUG_DP("wide_bus_en=%d\n", dp->wide_bus_en);
>>> return ret;
>>> }
>>>
>>> @@ -1503,6 +1507,8 @@ int msm_dp_modeset_init(struct msm_dp
>>> *dp_display, struct drm_device *dev,
>>> {
>>> struct msm_drm_private *priv;
>>> struct dp_display_private *dp_priv;
>>> + struct msm_op_info *op;
>>> + struct dp_display_private *dp;
>>> int ret;
>>>
>>> if (WARN_ON(!encoder) || WARN_ON(!dp_display) || WARN_ON(!dev))
>>> @@ -1545,6 +1551,17 @@ int msm_dp_modeset_init(struct msm_dp
>>> *dp_display, struct drm_device *dev,
>>>
>>> priv->bridges[priv->num_bridges++] = dp_display->bridge;
>>>
>>> + dp = container_of(dp_display, struct dp_display_private,
>>> dp_display);
>>> +
>>> + dp_display->wide_bus_en = dp->parser->has_widebus;
>>> + dp_display->compression_en = dp->parser->has_compression;
>>> +
>>> + op = &priv->op_info[dp->id];
>>> + op->wide_bus_en = dp_display->wide_bus_en;
>>> + op->compression_en = dp_display->compression_en;
>>> +
>>> + drm_dbg_dp(dp->drm_dev, "id=%d widebus=%d compression=%d\n",
>>> + dp->id, op->wide_bus_en, op->compression_en);
>>> return 0;
>>> }
>>>
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.h
>>> b/drivers/gpu/drm/msm/dp/dp_display.h
>>> index e3adcd5..b1057cb 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_display.h
>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.h
>>> @@ -24,6 +24,9 @@ struct msm_dp {
>>>
>>> hdmi_codec_plugged_cb plugged_cb;
>>>
>>> + bool wide_bus_en;
>>> + bool compression_en;
>>> +
>>> u32 max_pclk_khz;
>>>
>>> u32 max_dp_lanes;
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_parser.c
>>> b/drivers/gpu/drm/msm/dp/dp_parser.c
>>> index e74012d..fd48eb8 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_parser.c
>>> +++ b/drivers/gpu/drm/msm/dp/dp_parser.c
>>> @@ -286,6 +286,28 @@ static int dp_parser_find_panel(struct dp_parser
>>> *parser)
>>> return 0;
>>> }
>>>
>>> +static void dp_parser_compression(struct dp_parser *parser)
>>> +{
>>> + struct device *dev = &parser->pdev->dev;
>>> +
>>> + parser->has_compression = of_property_read_bool(dev->of_node,
>>> + "qcom,compression-enable");
>>> +
>>> + DRM_DEBUG_DP("compression parsing successful. compression:%d\n",
>>> + parser->has_compression);
>>> +}
>>> +
>>> +static void dp_parser_widebus(struct dp_parser *parser)
>>> +{
>>> + struct device *dev = &parser->pdev->dev;
>>> +
>>> + parser->has_widebus = of_property_read_bool(dev->of_node,
>>> + "qcom,widebus-enable");
>>> +
>>> + DRM_DEBUG_DP("widebus parsing successful. widebus:%d\n",
>>> + parser->has_widebus);
>>> +}
>> All new properties should be described in the dt-bindings document.
>>
>> However I have a bigger question here. Who and how decides whether
>> compression or widebus should be enabled?
>>
>> Should we enable widebus for all generations that support it? If so,
>> this should be a part of msm_dp_config rather than the DTS property.
>> And I'm completely puzzled about the compression-enable here.
>>
>>
>>> +
>>> static int dp_parser_parse(struct dp_parser *parser, int
>>> connector_type)
>>> {
>>> int rc = 0;
>>> @@ -319,6 +341,10 @@ static int dp_parser_parse(struct dp_parser
>>> *parser, int connector_type)
>>> */
>>> parser->regulator_cfg = &sdm845_dp_reg_cfg;
>>>
>>> + dp_parser_widebus(parser);
>>> +
>>> + dp_parser_compression(parser);
>>> +
>>> return 0;
>>> }
>>>
>>> diff --git a/drivers/gpu/drm/msm/dp/dp_parser.h
>>> b/drivers/gpu/drm/msm/dp/dp_parser.h
>>> index 3172da0..7531fe2 100644
>>> --- a/drivers/gpu/drm/msm/dp/dp_parser.h
>>> +++ b/drivers/gpu/drm/msm/dp/dp_parser.h
>>> @@ -123,6 +123,8 @@ struct dp_parser {
>>> struct dp_display_data disp_data;
>>> const struct dp_regulator_cfg *regulator_cfg;
>>> u32 max_dp_lanes;
>>> + bool has_widebus;
>>> + bool has_compression;
>>> struct drm_bridge *panel_bridge;
>>>
>>> int (*parse)(struct dp_parser *parser, int connector_type);
>>> diff --git a/drivers/gpu/drm/msm/msm_drv.h
>>> b/drivers/gpu/drm/msm/msm_drv.h
>>> index d7574e6..1a5f3e9 100644
>>> --- a/drivers/gpu/drm/msm/msm_drv.h
>>> +++ b/drivers/gpu/drm/msm/msm_drv.h
>>> @@ -127,6 +127,11 @@ struct msm_display_info {
>>> bool is_te_using_watchdog_timer;
>>> };
>>>
>>> +struct msm_op_info {
>>> + bool wide_bus_en;
>>> + bool compression_en;
>>> +};
>>> +
>>> /* Commit/Event thread specific structure */
>>> struct msm_drm_thread {
>>> struct drm_device *dev;
>>> @@ -156,6 +161,8 @@ struct msm_drm_private {
>>>
>>> struct msm_dp *dp[MSM_DP_CONTROLLER_COUNT];
>>>
>>> + struct msm_op_info op_info[MSM_DP_CONTROLLER_COUNT];
>>> +
>> As I said before, it should be INTF_MAX. Or you can retrieve it from
>> priv->dp as needed instead.
>>
>>> /* when we have more than one 'msm_gpu' these need to be an
>>> array: */
>>> struct msm_gpu *gpu;
>>>
>>> @@ -338,6 +345,8 @@ int msm_hdmi_modeset_init(struct hdmi *hdmi,
>>> struct drm_device *dev,
>>> void __init msm_hdmi_register(void);
>>> void __exit msm_hdmi_unregister(void);
>>>
>>> +struct msm_dp;
>>> +
>>> struct msm_dsi;
>>> #ifdef CONFIG_DRM_MSM_DSI
>>> int dsi_dev_attach(struct platform_device *pdev);
>>> --
>>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
>>> Forum,
>>> a Linux Foundation Collaborative Project
>>>
>>
--
With best wishes
Dmitry
More information about the Freedreno
mailing list