[Freedreno] [PATCH v4 2/3] phy/qualcomm: add regulator_set_load to dp phy

[Dmitry Baryshkov]

On Thu, 19 May 2022 at 00:36, Kuogee Hsieh <quic_khsieh at quicinc.com> wrote:
>
> This patch add regulator_set_load() before enable regulator at
> DP phy driver.
>
> Signed-off-by: Kuogee Hsieh <quic_khsieh at quicinc.com>
> Reviewed-by: Stephen Boyd <swboyd at chromium.org>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp.c | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index b144ae1..20ac446 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -3130,6 +3130,7 @@ struct qmp_phy_cfg {
>         int num_resets;
>         /* regulators to be requested */
>         const char * const *vreg_list;
> +       const unsigned int *vreg_enable_load;
>         int num_vregs;
>
>         /* array of registers with different offsets */
> @@ -3346,6 +3347,10 @@ static const char * const qmp_phy_vreg_l[] = {
>         "vdda-phy", "vdda-pll",
>  };
>
> +static const unsigned int qmp_phy_vreg_enable_load[] = {
> +       21800, 36000
> +};
> +
>  static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = {
>         .type                   = PHY_TYPE_USB3,
>         .nlanes                 = 1,
> @@ -4072,6 +4077,7 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
>         .reset_list             = msm8996_usb3phy_reset_l,
>         .num_resets             = ARRAY_SIZE(msm8996_usb3phy_reset_l),
>         .vreg_list              = qmp_phy_vreg_l,
> +       .vreg_enable_load       = qmp_phy_vreg_enable_load,
>         .num_vregs              = ARRAY_SIZE(qmp_phy_vreg_l),
>         .regs                   = qmp_v4_usb3phy_regs_layout,
>
> @@ -4139,6 +4145,7 @@ static const struct qmp_phy_cfg sm8250_dpphy_cfg = {
>         .reset_list             = msm8996_usb3phy_reset_l,
>         .num_resets             = ARRAY_SIZE(msm8996_usb3phy_reset_l),
>         .vreg_list              = qmp_phy_vreg_l,
> +       .vreg_enable_load       = qmp_phy_vreg_enable_load,
>         .num_vregs              = ARRAY_SIZE(qmp_phy_vreg_l),
>         .regs                   = qmp_v4_usb3phy_regs_layout,

I'd ask again: what about the sdm845? SC8180x? SC7180? Do we need to
change them too?
Currently they will all be handled by the DP driver.

>
> @@ -5008,6 +5015,11 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
>                 return 0;
>         }
>
> +       if (cfg->vreg_enable_load) {
> +               for (i = cfg->num_vregs - 1; i >= 0; --i)
> +                       regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_enable_load[i]);
> +       }
> +
>         /* turn on regulator supplies */
>         ret = regulator_bulk_enable(cfg->num_vregs, qmp->vregs);
>         if (ret) {
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>


-- 
With best wishes
Dmitry