[Freedreno] [PATCH v1 7/9] arm64: dts: qcom: sm8350: Add display system nodes
Robert Foss
robert.foss at linaro.org
Fri Nov 11 15:16:38 UTC 2022
On Sat, 29 Oct 2022 at 00:01, Krzysztof Kozlowski
<krzysztof.kozlowski at linaro.org> wrote:
>
> On 28/10/2022 08:08, Robert Foss wrote:
> > Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
> > nodes the display subsystem is configured to support
> > one DSI output.
> >
> > Signed-off-by: Robert Foss <robert.foss at linaro.org>
> > ---
> > arch/arm64/boot/dts/qcom/sm8350.dtsi | 196 ++++++++++++++++++++++++++-
> > 1 file changed, 192 insertions(+), 4 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > index b6e44cd3b394..eaa3cdee1860 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > @@ -3,6 +3,7 @@
> > * Copyright (c) 2020, Linaro Limited
> > */
> >
> > +#include <dt-bindings/interconnect/qcom,sm8350.h>
> > #include <dt-bindings/interrupt-controller/arm-gic.h>
> > #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
> > #include <dt-bindings/clock/qcom,gcc-sm8350.h>
> > @@ -2535,14 +2536,200 @@ usb_2_dwc3: usb at a800000 {
> > };
> > };
> >
> > + mdss: mdss at ae00000 {
> > + compatible = "qcom,sm8350-mdss";
> > + reg = <0 0x0ae00000 0 0x1000>;
> > + reg-names = "mdss";
> > +
> > + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
> > + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
> > + interconnect-names = "mdp0-mem", "mdp1-mem";
> > +
> > + power-domains = <&dispcc MDSS_GDSC>;
> > + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> > +
> > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > + <&gcc GCC_DISP_HF_AXI_CLK>,
> > + <&gcc GCC_DISP_SF_AXI_CLK>,
> > + <&dispcc DISP_CC_MDSS_MDP_CLK>;
> > + clock-names = "iface", "bus", "nrt_bus", "core";
> > +
> > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > +
> > + status = "ok";
>
> No need for this.
Ack, I'll switch to disabled.
>
> > +
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + mdss_mdp: mdp at ae01000 {
>
> Node name: display-controller
Ack.
> > + compatible = "qcom,sm8350-dpu";
> > + reg = <0 0x0ae01000 0 0x8f000>,
> > + <0 0x0aeb0000 0 0x2008>;
> > + reg-names = "mdp", "vbif";
> > + iommus = <&apps_smmu 0x820 0x402>;
> > +
> > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> > + <&gcc GCC_DISP_SF_AXI_CLK>,
> > + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> > + <&dispcc DISP_CC_MDSS_MDP_CLK>,
> > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > + clock-names = "bus",
> > + "nrt_bus",
> > + "iface",
> > + "lut",
> > + "core",
> > + "vsync";
> > +
> > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > + assigned-clock-rates = <19200000>;
> > +
> > + operating-points-v2 = <&mdp_opp_table>;
> > + power-domains = <&rpmhpd SM8350_MMCX>;
> > +
> > + interrupt-parent = <&mdss>;
> > + interrupts = <0>;
> > +
> > + status = "ok";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + dpu_intf1_out: endpoint {
> > + remote-endpoint = <&dsi0_in>;
> > + };
> > + };
> > + };
> > +
> > + mdp_opp_table: mdp-opp-table {
>
> I have doubts that it passes dtbs_checks... opp-table
Ack.
>
> > + compatible = "operating-points-v2";
> > +
> > + opp-200000000 {
> > + opp-hz = /bits/ 64 <200000000>;
> > + required-opps = <&rpmhpd_opp_low_svs>;
> > + };
> > +
> > + opp-300000000 {
> > + opp-hz = /bits/ 64 <300000000>;
> > + required-opps = <&rpmhpd_opp_svs>;
> > + };
> > +
> > + opp-345000000 {
> > + opp-hz = /bits/ 64 <345000000>;
> > + required-opps = <&rpmhpd_opp_svs_l1>;
> > + };
> > +
> > + opp-460000000 {
> > + opp-hz = /bits/ 64 <460000000>;
> > + required-opps = <&rpmhpd_opp_nom>;
> > + };
> > + };
> > + };
> > +
> > + dsi0: dsi at ae94000 {
> > + compatible = "qcom,mdss-dsi-ctrl";
> > + reg = <0 0x0ae94000 0 0x400>;
> > + reg-names = "dsi_ctrl";
> > +
> > + interrupt-parent = <&mdss>;
> > + interrupts = <4>;
> > +
> > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> > + <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> > + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > + <&gcc GCC_DISP_HF_AXI_CLK>;
> > + clock-names = "byte",
> > + "byte_intf",
> > + "pixel",
> > + "core",
> > + "iface",
> > + "bus";
> > +
> > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
> > + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> > + assigned-clock-parents = <&dsi0_phy 0>,
> > + <&dsi0_phy 1>;
> > +
> > + operating-points-v2 = <&dsi_opp_table>;
> > + power-domains = <&rpmhpd SM8350_MMCX>;
> > +
> > + phys = <&dsi0_phy>;
> > + phy-names = "dsi";
> > +
> > + status = "disabled";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + dsi0_in: endpoint {
> > + remote-endpoint = <&dpu_intf1_out>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <1>;
> > + dsi0_out: endpoint {
> > + };
> > + };
> > + };
> > + };
> > +
> > + dsi0_phy: dsi-phy at ae94400 {
>
> Just "phy". I think Dmitry was renaming all of these.
Ack.
>
> > + compatible = "qcom,dsi-phy-5nm-8350";
> > + reg = <0 0x0ae94400 0 0x200>,
> > + <0 0x0ae94600 0 0x280>,
> > + <0 0x0ae94900 0 0x260>;
> > + reg-names = "dsi_phy",
> > + "dsi_phy_lane",
> > + "dsi_pll";
> > +
> > + #clock-cells = <1>;
> > + #phy-cells = <0>;
> > +
> > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > + <&rpmhcc RPMH_CXO_CLK>;
> > + clock-names = "iface", "ref";
> > +
> > + status = "disabled";
> > +
> > + dsi_opp_table: dsi-opp-table {
>
> opp-table
Ack
>
> Run `make dtbs_check`
I had a look after fixing the above and I'm seeing some other issues.
Due to the dts/dt-binding rework that Dmitry is doing, I'll leave some
warnings, which can be addressed once the rework changes have landed.
>
>
> Best regards,
> Krzysztof
>
More information about the Freedreno
mailing list