[Freedreno] [PATCH v2 2/5] arm64: dts: qcom: sm8450: add display hardware devices
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Tue Nov 22 23:36:56 UTC 2022
Add devices tree nodes describing display hardware on SM8450:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs
This does not provide support for DP controllers present on SM8450.
Reviewed-by: Konrad Dybcio <konrad.dybcio at somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++-
1 file changed, 280 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 8cc9f62f7645..0c3a3a5578b0 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2394,6 +2394,282 @@ camcc: clock-controller at ade0000 {
status = "disabled";
};
+ mdss: mdss at ae00000 {
+ compatible = "qcom,sm8450-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ /* same path used twice */
+ interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
+ <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "nrt_bus", "core";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x2800 0x402>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss_mdp: display-controller at ae01000 {
+ compatible = "qcom,sm8450-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ operating-points-v2 = <&mdp_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&mdss_dsi0_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&mdss_dsi1_in>;
+ };
+ };
+
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-172000000 {
+ opp-hz = /bits/ 64 <172000000>;
+ required-opps = <&rpmhpd_opp_low_svs_d1>;
+ };
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-325000000 {
+ opp-hz = /bits/ 64 <325000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dsi0: dsi at ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ phys = <&mdss_dsi0_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ mdss_dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ mdss_dsi0_out: endpoint {
+ };
+ };
+ };
+
+ mdss_dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ mdss_dsi0_phy: phy at ae94400 {
+ compatible = "qcom,dsi-phy-5nm-8450";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ mdss_dsi1: dsi at ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ phys = <&mdss_dsi1_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ mdss_dsi1_in: endpoint {
+ remote-endpoint = <&dpu_intf2_out>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ mdss_dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi1_phy: phy at ae96400 {
+ compatible = "qcom,dsi-phy-5nm-8450";
+ reg = <0 0x0ae96400 0 0x200>,
+ <0 0x0ae96600 0 0x280>,
+ <0 0x0ae96900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+ };
+
dispcc: clock-controller at af00000 {
compatible = "qcom,sm8450-dispcc";
reg = <0 0x0af00000 0 0x20000>;
@@ -2401,10 +2677,10 @@ dispcc: clock-controller at af00000 {
<&rpmhcc RPMH_CXO_CLK_A>,
<&gcc GCC_DISP_AHB_CLK>,
<&sleep_clk>,
- <0>, /* dsi0 */
- <0>,
- <0>, /* dsi1 */
- <0>,
+ <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>,
+ <&mdss_dsi1_phy 0>,
+ <&mdss_dsi1_phy 1>,
<0>, /* dp0 */
<0>,
<0>, /* dp1 */
--
2.35.1
More information about the Freedreno
mailing list