[Freedreno] [PATCH v1 7/9] arm64: dts: qcom: sm8350: Add display system nodes
Bjorn Andersson
andersson at kernel.org
Fri Oct 28 13:50:09 UTC 2022
On Fri, Oct 28, 2022 at 02:08:10PM +0200, Robert Foss wrote:
> Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
> nodes the display subsystem is configured to support
> one DSI output.
>
> Signed-off-by: Robert Foss <robert.foss at linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350.dtsi | 196 ++++++++++++++++++++++++++-
> 1 file changed, 192 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> index b6e44cd3b394..eaa3cdee1860 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> @@ -3,6 +3,7 @@
> * Copyright (c) 2020, Linaro Limited
> */
>
> +#include <dt-bindings/interconnect/qcom,sm8350.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
> #include <dt-bindings/clock/qcom,gcc-sm8350.h>
> @@ -2535,14 +2536,200 @@ usb_2_dwc3: usb at a800000 {
> };
> };
>
> + mdss: mdss at ae00000 {
display-subsystem at ae00000 please.
> + compatible = "qcom,sm8350-mdss";
> + reg = <0 0x0ae00000 0 0x1000>;
> + reg-names = "mdss";
> +
> + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
> + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "mdp0-mem", "mdp1-mem";
> +
> + power-domains = <&dispcc MDSS_GDSC>;
> + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface", "bus", "nrt_bus", "core";
> +
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + status = "ok";
You want "disabled" here, and then "okay" in the .dts.
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + mdss_mdp: mdp at ae01000 {
display-controller at ae01000 please.
> + compatible = "qcom,sm8350-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> + iommus = <&apps_smmu 0x820 0x402>;
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + operating-points-v2 = <&mdp_opp_table>;
> + power-domains = <&rpmhpd SM8350_MMCX>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0>;
> +
> + status = "ok";
"okay", but this is the default, so you can skip it in the .dtsi
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> + };
> +
> + mdp_opp_table: mdp-opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-200000000 {
> + opp-hz = /bits/ 64 <200000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-300000000 {
> + opp-hz = /bits/ 64 <300000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-345000000 {
> + opp-hz = /bits/ 64 <345000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-460000000 {
> + opp-hz = /bits/ 64 <460000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> +
> + dsi0: dsi at ae94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0 0x0ae94000 0 0x400>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> + <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&gcc GCC_DISP_HF_AXI_CLK>;
> + clock-names = "byte",
> + "byte_intf",
> + "pixel",
> + "core",
> + "iface",
> + "bus";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
> + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> + assigned-clock-parents = <&dsi0_phy 0>,
> + <&dsi0_phy 1>;
> +
> + operating-points-v2 = <&dsi_opp_table>;
> + power-domains = <&rpmhpd SM8350_MMCX>;
> +
> + phys = <&dsi0_phy>;
> + phy-names = "dsi";
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&dpu_intf1_out>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi0_phy: dsi-phy at ae94400 {
> + compatible = "qcom,dsi-phy-5nm-8350";
> + reg = <0 0x0ae94400 0 0x200>,
> + <0 0x0ae94600 0 0x280>,
> + <0 0x0ae94900 0 0x260>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> +
> + status = "disabled";
> +
> + dsi_opp_table: dsi-opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-187500000 {
> + opp-hz = /bits/ 64 <187500000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-300000000 {
> + opp-hz = /bits/ 64 <300000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-358000000 {
> + opp-hz = /bits/ 64 <358000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> + };
> + };
> + };
> +
> dispcc: clock-controller at af00000 {
> compatible = "qcom,sm8350-dispcc";
> reg = <0 0x0af00000 0 0x10000>;
> clocks = <&rpmhcc RPMH_CXO_CLK>,
> - <0>,
> - <0>,
> - <0>,
> - <0>,
> + <&dsi0_phy 0>, <&dsi0_phy 1>,
> + <0>, <0>,
> <0>,
> <0>;
> clock-names = "bi_tcxo",
> @@ -2557,6 +2744,7 @@ dispcc: clock-controller at af00000 {
> #power-domain-cells = <1>;
>
> power-domains = <&rpmhpd SM8350_MMCX>;
> + required-opps = <&rpmhpd_opp_turbo>;
That seems a little bit aggressive, is the opp-based voting from within
the mdss/dpu not sufficient?
Regards,
Bjorn
> };
>
> adsp: remoteproc at 17300000 {
> --
> 2.34.1
>
More information about the Freedreno
mailing list