[Freedreno] [PATCH v2] drm/panel: Enable DSC and CMD mode for Visionox VTDR6130 panel
neil.armstrong at linaro.org
neil.armstrong at linaro.org
Tue Aug 1 08:26:54 UTC 2023
On 28/07/2023 23:44, Jessica Zhang wrote:
>
>
> On 7/28/2023 2:37 AM, Dmitry Baryshkov wrote:
>> On Fri, 28 Jul 2023 at 04:26, Paloma Arellano <quic_parellan at quicinc.com> wrote:
>>>
>>> Enable display compression (DSC v1.2) and CMD mode for 1080x2400 Visionox
>>> VTDR6130 AMOLED DSI panel. In addition, this patch will set the default
>>> to command mode with DSC enabled.
>>>
>>> Note: This patch has only been validated DSC over command mode as DSC over
>>> video mode has never been validated for the MSM driver before.
>>>
>>> Depends on: "Add prepare_prev_first flag to Visionox VTDR6130" [1]
>>>
>>> Changes since v1:
>>> - Changed from email address
>>>
>>> [1] https://patchwork.freedesktop.org/series/121337/
>>>
>>> Suggested-by: Jessica Zhang <quic_jesszhan at quicinc.com>
>>> Signed-off-by: Paloma Arellano <quic_parellan at quicinc.com>
>>> ---
>>> .../gpu/drm/panel/panel-visionox-vtdr6130.c | 77 ++++++++++++++++++-
>>> 1 file changed, 73 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/panel/panel-visionox-vtdr6130.c b/drivers/gpu/drm/panel/panel-visionox-vtdr6130.c
>>> index e1363e128e7e..5658d39a3a6b 100644
>>> --- a/drivers/gpu/drm/panel/panel-visionox-vtdr6130.c
>>> +++ b/drivers/gpu/drm/panel/panel-visionox-vtdr6130.c
>>> @@ -9,6 +9,7 @@
>>> #include <linux/of.h>
>>>
>>> #include <drm/display/drm_dsc.h>
>>> +#include <drm/display/drm_dsc_helper.h>
>>> #include <drm/drm_mipi_dsi.h>
>>> #include <drm/drm_modes.h>
>>> #include <drm/drm_panel.h>
>>> @@ -20,7 +21,8 @@ struct visionox_vtdr6130 {
>>> struct mipi_dsi_device *dsi;
>>> struct gpio_desc *reset_gpio;
>>> struct regulator_bulk_data supplies[3];
>>> - bool prepared;
>>> + bool prepared, enabled;
>>> + bool video_mode;
>>> };
>>>
>>> static inline struct visionox_vtdr6130 *to_visionox_vtdr6130(struct drm_panel *panel)
>>> @@ -50,12 +52,18 @@ static int visionox_vtdr6130_on(struct visionox_vtdr6130 *ctx)
>>> if (ret)
>>> return ret;
>>>
>>> + mipi_dsi_dcs_write_seq(dsi, 0x03, 0x01);
>>> mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x20);
>>> mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_SET_DISPLAY_BRIGHTNESS, 0x00, 0x00);
>>> mipi_dsi_dcs_write_seq(dsi, 0x59, 0x09);
>>> mipi_dsi_dcs_write_seq(dsi, 0x6c, 0x01);
>>> mipi_dsi_dcs_write_seq(dsi, 0x6d, 0x00);
>>> - mipi_dsi_dcs_write_seq(dsi, 0x6f, 0x01);
>>> +
>>> + if (ctx->video_mode)
>>> + mipi_dsi_dcs_write_seq(dsi, 0x6f, 0x01);
>>> + else
>>> + mipi_dsi_dcs_write_seq(dsi, 0x6f, 0x02);
>>> +
>>> mipi_dsi_dcs_write_seq(dsi, 0x70,
>>> 0x12, 0x00, 0x00, 0xab, 0x30, 0x80, 0x09, 0x60, 0x04,
>>> 0x38, 0x00, 0x28, 0x02, 0x1c, 0x02, 0x1c, 0x02, 0x00,
>>> @@ -214,6 +222,42 @@ static const struct drm_display_mode visionox_vtdr6130_mode = {
>>> .height_mm = 157,
>>> };
>>>
>>> +static int visionox_vtdr6130_enable(struct drm_panel *panel)
>>> +{
>>> + struct visionox_vtdr6130 *ctx = to_visionox_vtdr6130(panel);
>>> + struct mipi_dsi_device *dsi = ctx->dsi;
>>> + struct drm_dsc_picture_parameter_set pps;
>>> + int ret;
>>> +
>>> + if (ctx->enabled)
>>> + return 0;
>>> +
>>> + if (!dsi->dsc) {
>>> + dev_err(&dsi->dev, "DSC not attached to DSI\n");
>>> + return -ENODEV;
>>> + }
>>
>> The error message is misleading. Also, if you don't want to enable DSC
>> for the video mode, this will break.
>>
>>> +
>>> + drm_dsc_pps_payload_pack(&pps, dsi->dsc);
>>> + ret = mipi_dsi_picture_parameter_set(dsi, &pps);
>>> + if (ret) {
>>> + dev_err(&dsi->dev, "Failed to set PPS\n");
>>> + return ret;
>>> + }
>>> +
>>> + ctx->enabled = true;
>>
>> Do we need this refcount just for PPS upload? What will happen if PPS
>> is uploaded several times?
>>
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int visionox_vtdr6130_disable(struct drm_panel *panel)
>>> +{
>>> + struct visionox_vtdr6130 *ctx = to_visionox_vtdr6130(panel);
>>> +
>>> + ctx->enabled = false;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> static int visionox_vtdr6130_get_modes(struct drm_panel *panel,
>>> struct drm_connector *connector)
>>> {
>>> @@ -237,6 +281,8 @@ static const struct drm_panel_funcs visionox_vtdr6130_panel_funcs = {
>>> .prepare = visionox_vtdr6130_prepare,
>>> .unprepare = visionox_vtdr6130_unprepare,
>>> .get_modes = visionox_vtdr6130_get_modes,
>>> + .enable = visionox_vtdr6130_enable,
>>> + .disable = visionox_vtdr6130_disable,
>>> };
>>>
>>> static int visionox_vtdr6130_bl_update_status(struct backlight_device *bl)
>>> @@ -269,11 +315,31 @@ static int visionox_vtdr6130_probe(struct mipi_dsi_device *dsi)
>>> {
>>> struct device *dev = &dsi->dev;
>>> struct visionox_vtdr6130 *ctx;
>>> + struct drm_dsc_config *dsc;
>>> int ret;
>>>
>>> ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
>>> if (!ctx)
>>> return -ENOMEM;
>>> +
>>> + ctx->video_mode = of_property_read_bool(dev->of_node, "enforce-video-mode");
>>
>> Please also add a DT bindings patch.
>>
>>> +
>>> + dsc = devm_kzalloc(dev, sizeof(*dsc), GFP_KERNEL);
>>> + if (!dsc)
>>> + return -ENOMEM;
>>
>> You can add struct drm_dsc_config to struct visionox_vtdr6130 instead
>> of allocating it.
>>
>>> +
>>> + /* Set DSC params */
>>> + dsc->dsc_version_major = 0x1;
>>> + dsc->dsc_version_minor = 0x2;
>>> +
>>> + dsc->slice_height = 40;
>>> + dsc->slice_width = 540;
>>> + dsc->slice_count = 2;
>>> + dsc->bits_per_component = 8;
>>> + dsc->bits_per_pixel = 8 << 4;
>>> + dsc->block_pred_enable = true;
>>> +
>>> + dsi->dsc = dsc;
>>
>> Only in command mode?
>
> Hi Dmitry,
>
> The intention of the patch wasn't to enable DSC for only command mode.
>
> We didn't want to limit DSC to only command mode because, while the MSM DPU driver isn't able to validate DSC on video mode, other vendors might have already validated DSC on video mode and would benefit from this patch.
>
> FWIW, inital driver commit [1] notes that the panel is meant to work with compressed streams in general and DSC support was tob be added later on.
The panel supports Video, Video+DSC, CMD, CMD+DSC, so it would be great to be able to
select any of the supported modes, including the non-compressed ones.
So enforce-video-mode is great, but an enforce-uncompressed-mode would be necessary
aswell.
Neil
>
> Thanks,
>
> Jessica Zhang
>
> [1] https://patchwork.freedesktop.org/patch/517483/?series=112369&rev=2
>
>>
>>>
>>> ctx->supplies[0].supply = "vddio";
>>> ctx->supplies[1].supply = "vci";
>>> @@ -294,8 +360,11 @@ static int visionox_vtdr6130_probe(struct mipi_dsi_device *dsi)
>>>
>>> dsi->lanes = 4;
>>> dsi->format = MIPI_DSI_FMT_RGB888;
>>> - dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_NO_EOT_PACKET |
>>> - MIPI_DSI_CLOCK_NON_CONTINUOUS;
>>> +
>>> + dsi->mode_flags = MIPI_DSI_MODE_NO_EOT_PACKET | MIPI_DSI_CLOCK_NON_CONTINUOUS;
>>
>> Keep the line split please.
>>
>>> + if (ctx->video_mode)
>>> + dsi->mode_flags |= MIPI_DSI_MODE_VIDEO;
>>> +
>>> ctx->panel.prepare_prev_first = true;
>>>
>>> drm_panel_init(&ctx->panel, dev, &visionox_vtdr6130_panel_funcs,
>>> --
>>> 2.41.0
>>>
>>
>>
>> --
>> With best wishes
>> Dmitry
More information about the Freedreno
mailing list